Rotary S
Rotary S - SRS #4628
DESCRIPTION: Simco; Model: 2800; Mud Pump: Moyno 3L8; Engine: PTO; Mounted On: 2005 Ford F550 4WD; Truck Engine Make: Powerstroke V8; Condition: Working; Tools/Options: Simco 2800: 140# Auto Hammer, 13,500# Pullback, One Auxiliary Winch, 3 Leveling Jacks. Rig has < 2,000 Hours on it. Truck has approx. 103,634 Miles on it and Toolboxes. 2026 New Rack on the Truck, New Moyno Pump, Replaced the PTO and Repaired the 2 Hydraulic Pumps. Includes a 2003 Ford F550 Flatbed Chase Truck, Dual Axle, 6.0 Engine with approx. 213,000 Miles on it. Runs Strong, A/C, New Rack Installed. Condition: Working
Rotary S - SRS #4625
DESCRIPTION: 2001, Schramm; Model: T300M; Compressor: See Below - Off-Board; Mud Pump: See Below; Mounted On: 2000 IHC 4900; Truck Engine Make: DT 530; Tools/Options: Schramm T300M Year: 2001: Rig was Fully Serviced when Recently Parked. Rig has an On-Board Mud Puppy System that has 3 Desanders, Homemade Tank and 3 Mud Puppy Shakers, 4X3 Centrifugal Mission Mud Pump on Board with New Fluid End 50 Hours Ago. Factory Warranty Engine with Low Hours (4-5 Seasons on it), Electric over Hudraulics, 2 Hydraulic Cylinders to be Replaced on the Carousel. Air Compressor has been Removed and needs gone through. Drill is set up to run 3.5" Schramm Drill Rod, 10-Rod Carousel set up for 20' Rods. Truck has Front Wheel Assist, Locks Side to Side. Includes: (10) 3.5" Drills Rods that are Worn, Spare Swivel O-Rings, some Spare Parts.
Rotary S - SRS #4514
DESCRIPTION: 2003, Schramm; Model: T555; Compressor: Sullair 1050/350; Engine: CAT C15; Mounted On: Sterling; Truck Engine Make: CAT; Tools/Options: Schramm T555 Year: 2003: Less than 2,000 Hours since Compressor Rebuild. Hours of Gauge Reads 9,653. Main Pump Recently Rebuilt (2025), 6-Rod Carousel Inside Cable Feed, Basic Rod Handling. Table Bushings & Basic Tooling Included. No Pipe Included but approx. 200' of 4.5" OD X 20' with 3.5" API Threads Available for an Extra Cost. Truck Odometer Reads 19,206 Miles. Recently Serviced (2025) - Fluids & Filters.
Rotary S - SRS #4556
DESCRIPTION: 2008, Schramm; Model: T450WS; Compressor: 900/350; Engine: CAT 3406C; Mounted On: 2008 IHC 7500; Truck Engine Make: 570 HP; Condition: Working Drill - OPEN TO REASONABLE OFFERS; Tools/Options: Schramm T450WS Year: 2008: Hydraulic Welder, Oiler, New Rubber in the Back, Hendrickson Suspension, 30K Pullback, Rig is Set Up to Run 3.5" Drill Rod. New Chains in the last 2-1/2 Years, New Rollers in Mast, Mast is Straight, 3 Outriggers, 15-Rod Carousel, Bean Water Injection (rebuilt in 2024), Swinging Jib, Hydraulic Breakout Wrench, Aluminum Tool Box, No Sandline. Needs a New Sock in the Derrick. Includes 600' of good/used Drill Rod, Head Doughnuts, Complete Hose Kit for Big Compressor Hoses (1 hose used), Valve Rebuild Kit. Truck has approx. 54,000 Miles on it and Rig has approx. 7,000 Hours. Another 600' of Brand New 3.5" Drill Rod is Available for Extra Money. Truck Engine HP to be Confirmed.
Rotary S - SRS #4594
DESCRIPTION: 1986, Schramm; Model: T660; Compressor: 850/350; Engine: Detroit 8V92 REBUILT; Mounted On: 1986 GMC (2007 STERLING AVAILABLE); Truck Engine Make: CAT 3208; Condition: Ready to Drill PRICE REDUCED; Tools/Options: Schramm T660 Year: 1986: PRICE REDUCED. Well Maintained, Turnkey Drilling Setup Ready to Work. Deck Engine has approx. 1,000 Hours since rebuild. Other Components on the Drill have had Extensive Rebuilds Completed approx. 1,500 Hours ago. Including (about 90%) Hoses, Hydraulic Motors, Winches, Chains, Mast Cylinder, Controls, New Radiator and Oil Cooler. Comes with a Newly Rebuilt Head. Includes Motors. No Spindle. Truck has a 13-Speed Transmission. There is a 2007 Sterling LT9000 available for Mounting for Extra Money. It is Powered by a CAT C13 Engine, Automatic Transmission, Dual Power Steering, Jake Brake, Full Locking Rear ends, Heavy-Duty (thicker) Frame, Brand New Dash. Rig is Setup to Run 4.5" Drill Rod, Has an 18" Table Opening. Hour meter quit working shortly after current owner got it. Rig gets parked in the winter and is only used a as a backup rig. Welder not included.
Rotary S - SRS #4584
DESCRIPTION: 1989, Schramm; Model: T-660H; Compressor: 900/350 GHH; Mounted On: 2009 Mack Granite 6X4; Truck Engine Make: 485 HP; Condition: Good; Tools/Options: Schramm T-660H Year 1989: Rig is Capable of Holding 280' of 4.5" Drill Rod Standing up between the Lazy Susan and Rod Rack on the Side of the Mast. Rig has an 18" Table Opening. 40K Pullback, 30' of Travel as well as a Foremost Floating Sub. New Upgraded Piggyback Pump & Rotation Pump (2021), Deck Engine Completely Rebuilt in 2019, Upgraded Hydraulic Pumps, New Preheat Deck Engine Heater in 2022, Added Helpers Side Controls for Winch and Jib Boom. Compressor also Rebuilt around the same time as the deck engine (2019), best guess on hours is approx. 3,000 (working drill). Most Recently 2025-26 the Deck Engine had New Injectors Installed, Built a New Wiring Harness on Rig, Rebuilt Head & Installed a New Shaft through the Head, Upgraded the Air Seals to a King Swivel. Truck has an 18-Speed Transmission and approx. 46,345 Miles, Routine Maintenance done Yearly, New Injectors in 22/23. Previous Owner Purchased the Truck New. Includes approx. 600' - 700' of Drill Rod.
Rotary S - SRS #4573
DESCRIPTION: 1976, Speedstar; Model: SS15; Compressor: 256S 500/250 NOT MOUNTED; Mud Pump: GD 5X6; Mounted On: CCC; Truck Engine Make: Cummins 290; Tools/Options: Speedstar SS15 Year: 1976: 8-1/2" Retractable Table, Mechanical Clutches, Mast Extension Capable of Picking up 45' Pipe. Air Compressor Condition Unknown, Current Owner Never used it. New Pro Heat Engine Heater, New 2" Little Giant Swivel, New LF Breakout Tongs. Fresh Rebuild on the Lift Cylinders, Hydraulic Pumps and Motors. Mud Pump has had New Rods, Pistons, Valves, Seats, Liners and Packings Installed. New 700' of Sandline and 500' of New 4.5" X 20' Drill Rod with 2-7/8" IF Threads, 100' Never been in the ground. New 4.5" X 3' X 2-7/8" IF Sub with new 6-1/2" PDI Bit. New Sub 5-1/2" X 3' with 7-7/8" Roller cone Bit, (1) Hoisting Plug (2-7/8" IF), New work Platform, New Clutch for Mud Pump, New Pull Down, Shaft, Pillow Block Bearings and Sprockets. 500' of Rod will fit in rod box, compressor was removed and not used due to weight.
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350 with Clutch; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Mercedes Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005: Rig has 4 Jacks. Includes approx. 400' of 4.5" O.D. Drill Rod, (5) Joints are older 25'ers and the rest are 20'ers in better condition, a 6" and 8" Hammer & Bits, tools, Hydraulic Wrench, Casing Driver and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles. Total Rig Hours are approx. 10,000. Compressor has a clutch and has less hours but hours are unknown. Recently Installed a New Compressor Cooler (zero hours), New Shaft & Bearings in Rotary Head, Four Rebuilt Hydraulic Pumps and one new Pump.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
Rotary S - SRS #4491
DESCRIPTION: 1982, Schramm; Model: 685 DH; Compressor: See Below; Engine: 12V71 Twin Turbo; Mounted On: GMC; Truck Engine Make: 6V53 Turbo; Tools/Options: Schramm 685 DH Year: 1982: Last used in approx. 2024. Compressor wasn't used at that time, auxiliary air was used. On board compressor wasn't working, owner thinks it has a bad bearing. Compressor on Drill is a GHH 1000/350 - to be confirmed. Parts Rigs, Hurricane Booster and Wagon Style Sullair 900/350, Auxiliary Sullair Air Compressor Mounted on a Mack Truck with Hurricane Booster and approx. 2,200' of Schramm 25' Pipe with 3.5" API Regular Threads Available.
Rotary S - SRS #4485
DESCRIPTION: 1979, Schramm; Model: T985; Compressor: (2) 425/250; Engine: (2) 8V71 Turbo's; Mounted On: 4-Axle CCC; Truck Engine Make: 6V53; Tools/Options: Schramm T985 Year: 1979: Fresh Paint, Two Deck Engines, Two Compressors put out 350 PSI. Rig has had Recent M&R, not much has been done to Carrier Engine. One Front Jack, Two Rear, Fuller Transmission. Includes 1,000' of Drill Rod, Hammers, Bits.
Rotary S - SRS #4481
DESCRIPTION: Schramm; Model: T64; Compressor: 450/250 To be Confirmed; Engine: 8V Detroit; Truck Engine Make: 6V Detroit; Tools/Options: Schramm T64: Compressor size to be confirmed. Includes 400' of Drill Rod, 8" Stabilizer, Breakout Tools.
Rotary S - SRS #4465
DESCRIPTION: 1978, Simco; Model: 5000 WS; Mud Pump: Mission 4X3 Centrifugal; Engine: Ford 300; Mounted On: 1991 GMC Topkick - Single Axle Truck; Truck Engine Make: CAT 3208; Tools/Options: Simco 5000 WS Year: 1978: Single Axle, Automatic Transmission Truck, Pipe Rack, Driller & Helper Platforms, Toolboxes, Two Rear and One Front Jack. Mud Pump Rebuilt approx. 15 Wells Ago. No Sandline, Gearmatic Model 25 Winch, 13,600# Maximum Line Pull, Hydraulic Breakout Wrench, 10" Hinged Table, Swing out Tophead to Set Casing. Includes 150' of 4.5" X 15' Aluminum Flush Rod on the Truck, Multiple Bits. More Rod Available. Truck has approx. 106,373 Miles on it.
Rotary S - SRS #4441
DESCRIPTION: 1977, Speedstar; Model: SS-15; Compressor: LeRoi 600/250; Engine: PTO; Mounted On: CCC; Tools/Options: Speedstar SS-15 Year: 1977: Tophead Drive, 43' Mast, Manual Clutches. One Front Jack and Two Rear Jacks, Driller/Helper Platforms. Includes 300' of Drill Rod, Tiger Tierra Casing Hammer Available for an Extra Cost. Approx. 400,000 Miles. No Hour Meter.
Rotary S - SRS #4438
DESCRIPTION: Shopbuilt; Model: Similar to a Challenger M280; Mud Pump: See Below; Engine: 8V92T; Mounted On: 3-Axle Trailer; Tools/Options: Shopbuilt: Built in the Early 1980's, Pulldowns in Mast, 18" GEFCO/Speedstar Heavy Table, Power to Rear Axle is Powered by the8V92T with Allison Transmission & Drop Box (live, steerable axles on the trailer), Can Drive Rear End. Mast is 63' 6" and 6' Wide, 4" 250 Wall, 6 Lines, Trip & Kelly, 3" King Swivel, 5-1/2" Hex Kelly, Drums have 10 36 Dual Brakes, 18" Triple Disc Air Clutches, Air Clutches on Drawworks & Rotary Table. Can be Sold as a Package that Includes a Trailer Mounted 7-1/4" X 14" Gaso Mud Pump Powered by a 318 Detroit (other mud pumps available). 3,000' of 4.5" X-Hole Drill Pipe & Collars with Tandem Trailer. 3-Axle Trailer Drill is mounted on has 11 24 5 Bud Wheels, Trailer would need new tires if pulled a long distance. Condition: Last Drilled 3 Years Ago
Rotary S - SRS #4121
DESCRIPTION: 1975, Schramm; Model: T64HB; Compressor: 400/200 (to be confirmed); Mud Pump: 5X6; Engine: 318 Detroit; Mounted On: 1975 GMC; Truck Engine Make: Gas; Condition: One Owner; Tools/Options: Schramm T64HB Year: 1975: One Owner Drill! Compressor CFM/psi to be confirmed, could be 425/250 or 450/250. Water Injection, Oiler, Carousel hold 5 Rods and more can be hauled in the Pipe Rack. Engine was Overhauled in 2005, had Injection Work done to it. Approx. 500' of pipe and bits available for an extra cost. Last job was 2 years ago but can be started and run to show. Also has a 750/350 2-Wheel,Trailer Mounted Compressor available for an extra cost.
Rotary S - SRS #3400
DESCRIPTION: 1976, Speedstar; Model: SS-22; Compressor: LeRoi 256S2 445/250; Mud Pump: GD 5-1/2" X 8; Engine: PTO; Mounted On: 1976 3-Axle CCC; Truck Engine Make: Cummins; Condition: Good; Tools/Options: Speedstar SS-22 (1976): Hydraulic 10" Retractable Table, 34' Mast, 3-1/2" Fluted Kelly, 2" Little Giant Swivel, Double Drum with Sandline, Mechanical and Air Clutches, Engine Preheater. OFF MARKET, PUT BACK TO WORK
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |