Rotary S
Rotary S - SRS #4295
DESCRIPTION: 1978 or 1979, Simco; Model: 5000; Compressor: Developmental; Mud Pump: 3X4 and Air Operated Gardner Denver 5X6; Engine: PTO; Mounted On: 2020 IHC Single Axle; Truck Engine Make: Cummins; Tools/Options: Simco 5000: 1979 or 1980 Simco, Two Mud Pumps, GD is Air Operated, Manual Available. Mono Derrick, 20' Rod Rack, Single Axle Truck under CDL, Truck has approx. 111,000 Miles on it. New Planetary Pulldown for Hydraulic Motor, New Hydraulic Head Motor, Some New Hoses, Bearings Replaced., New Gauges in Console, Two New Front Leveling Jacks.
Rotary S - SRS #4479
DESCRIPTION: 2003, Schramm; Model: 450WS; Compressor: Sullair 900/350; Engine: CAT 3406 465 HP; Mounted On: 2004 Sterling 9500; Truck Engine Make: Mercedes 410 HP; Condition: PRICE REDUCED; Tools/Options: Schramm T450 WS Year: 2003: PRICE REDUCED! 25' Stroke, 20 GPM Water Injection Pump, Jib, 15-Pod Carousel, 4 Outriggers, 2 Behind Cab, 2 at Rear of Rig, Braden 15,000# Winch. Rig is set up to run 3.5" OD Drill Rod. 30K Pullback, 17K Pulldown. Compressor was Rebuilt in 2017. Compressor has approx. 1800-2000 Hours Since Rebuild. Deck Engine has approx. 10,000 Hours. Doesn't use oil but has a small oil leak behind the fuel pump. Dust Collector was added in 2010. Tophead was also Recently Replaced. Has been mostly used for Geothermal Drilling with a DTH bit. Truck has a Fuller Transmission. Includes 15 Drill Rods. Last drilled Feb-March 2025.
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005 Diesel; Compressor: 1050/350; Mud Pump: None; Mounted On: Sterling; TrEngine: , Diesel; Tools/Other Options: Includes Drill Rod, Tooling, 8" Hammer and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles.
Rotary S - SRS #4491
DESCRIPTION: 1982, Schramm; Model: 685 DH; Compressor: See Below; Mounted On: GMC; Tools/Options: Schramm 685 DH Year: 1982: Last used in approx. 2024. Compressor wasn't used at that time, auxiliary air was used. On board compressor wasn't working, owner thinks it has a bad bearing. Compressor is a 1000/350 - to be confirmed. Parts Rigs, Boosters, Auxiliary Air Compressor and approx. 1,200' of 25' Pipe Available.
Rotary S - SRS #4412
DESCRIPTION: 2006, Schramm; Model: T450WS; Compressor: 900/350 Sullair; Mud Pump: Gardner Denver 5X6 Hydraulic; Engine: CAT 3406C 465 HP; Mounted On: Mack Granite; Truck Engine Make: Mack AMI-370 405 HP; Condition: Well Maintained; Tools/Options: Schramm T450WS Year: 2006: Rebuilt Compressor and Tophead. 28'6" Mast Travel, Dual Tophead Motor, Rotation Torque Limiters, Dual Motors, 60" Breakout Wrench, 15-Rod Carousel, Lubricator, Outriggers, Jib Boom, 6" Hammer Holder, Walkways, 15,000# Winch, Water Injection, Pipe Rack. Rig is Set up to Run 3.5" X 20' Drill Rod with 2-3/8" IF Rod. No Rod Spinner or Floating Sub. Includes 400' of Drill Rod & Rod Handling Tools. Mud Pit Available. Est Total Hours are 12K and approx. 2K Hours on the Rebuilt Compressor. Tophead was also Recently Redone. Maintenance Records Available.
Rotary S - SRS #4485
DESCRIPTION: 1979, Schramm; Model: T985; Compressor: (2) 425/250; Engine: (2) 8V71 Turbo's; Mounted On: 4-Axle CCC; Truck Engine Make: 6V53; Tools/Options: Schramm T985 Year: 1979: Fresh Paint, Two Deck Engines, Two Compressors put out 350 PSI. Rig has had Recent M&R, not much has been done to Carrier Engine. One Front Jack, Two Rear, Fuller Transmission. Includes 1,000' of Drill Rod, Hammers, Bits.
Rotary S - SRS #4481
DESCRIPTION: Schramm; Model: T64; Compressor: 450/250 To be Confirmed; Engine: 8V Detroit; Truck Engine Make: 6V Detroit; Tools/Options: Schramm T64: Compressor size to be confirmed. Includes 400' of Drill Rod, 8" Stabilizer, Breakout Tools.
Rotary S - SRS #4366
DESCRIPTION: 1989, Schramm; Model: T660-H; Compressor: 900/350 GHH; Engine: 855 Cummins 450 HP; Mounted On: 2009 Mack Granite; Truck Engine Make: 485 HP; Condition: SOLD; Tools/Options: Schramm T-660H Year: 1989: SOLD Rig is Capable of Holding 280' of 4.5" Drill Rod Standing up between the Lazy Susan and Rod Rack on the Side of the Mast. 18" Table Opening. 40K Pullback, 30' of Travel as well as a Foremost Floating Sub. New Upgraded Piggyback Pump & Rotation Pump (2021), Deck Engine Completely Rebuilt in 2019, Upgraded Hydraulic Pumps, New Preheat Deck Engine Heater in 2022, Added Helpers Side Controls for Winch and Jib Boom. Compressor also rebuilt around the same time as the deck engine (2019), best guess on hours is approx. 3,000. Truck has an 18-Speed Transmission and approx. 46,345 Miles, Routine Maintenance done Yearly, New Injectors in 22/23. Includes Table Slips, Spare Rebuilt Starter for Deck Engine, New Water Pump for Deck Engine, Drive Coolers for Funk Box, New Upgraded Piggyback Hydraulic Pump for Water Injection/Rig Setup Circuit, New Braden Winch, New Hydraulic Motor for Radiator Fan, New Hydraulic Motor for CAT Pump, New hydraulic Rotation Motor Plus more Smaller Items. Complete Inventory List of Spare Parts & Items Included along with M&R Records Available. SOLD
Rotary S - SRS #4465
DESCRIPTION: 1978, Simco; Model: 5000 WS; Mud Pump: Mission 4X3 Centrifugal; Engine: Ford 300; Mounted On: 1991 GMC Topkick - Single Axle Truck; Truck Engine Make: CAT 3208; Tools/Options: Simco 5000 WS Year: 1978: Single Axle, Automatic Transmission Truck, Pipe Rack, Driller & Helper Platforms, Toolboxes, Two Rear and One Front Jack. Mud Pump Rebuilt approx. 15 Wells Ago. No Sandline, Gearmatic Model 25 Winch, 13,600# Maximum Line Pull, Hydraulic Breakout Wrench, 10" Hinged Table, Swing out Tophead to Set Casing. Includes 150' of 4.5" X 15' Aluminum Flush Rod on the Truck, Multiple Bits. More Rod Available. Truck has approx. 106,373 Miles on it.
Rotary S - SRS #4023
DESCRIPTION: 1981, Speedstar; Model: SS-40; Mud Pump: 7.5" X 10"; Engine: 6V71NA Detroit; Mounted On: 8X4 CCC; Truck Engine Make: 8V71 Detroit; Condition: SOLD; Tools/Options: Speedstar SS-40 Year: 1981: SOLD Double Drum Drawworks, Sandline Drum, Air Clutches, Catheads, Hydromatic Brake System, 4 Hydraulic Leveling Jacks, Under-Drive Air Clutch for Mud Pump Installation, King 50KG Mud Swivel, Allison Automatic Transmission, Hydraulically Raised 60' Derrick, (2) McKissick 3-Sheave Traveling Blocks, Kelly Bar, Derrick Night Lights, Speedstar 18" Rotary Table. Rear Hinged Rig Floor Platform, 4" Derrick Standpipe, 2" Mud Mixing Valve at Pump & 4" Ball Valve on Back Side of Mud Mixing Valve. Rebuilt Hydraulic Cylinders Including Outriggers, Derrick Raising and Tong Cylinders. Hydraulic Hoses on Derrick Raising Cylinders & all Outrigger Cylinders were replaced approx. 2 Years Ago. New Clutches, Recently Sandblasted, 2023, (currently being painted). Recent work includes Rebuilt Mud Pump (fluid end, clutches, belts), Rebuilt Deck Engine, New Brakes, Drums, Shoes on Carrier, Good Tires. Still needs Mud Lines, Gauges and Wiring. SOLD
Rotary S - SRS #4441
DESCRIPTION: 1977, Speedstar; Model: SS-15; Compressor: LeRoi 600/250; Engine: PTO; Mounted On: CCC; Tools/Options: Speedstar SS-15 Year: 1977: Tophead Drive, 43' Mast, Manual Clutches. One Front Jack and Two Rear Jacks, Driller/Helper Platforms. Includes 300' of Drill Rod, Tiger Tierra Casing Hammer Available for an Extra Cost. Approx. 400,000 Miles. No Hour Meter.
Rotary S - SRS #4438
DESCRIPTION: Shopbuilt; Model: Similar to a Challenger M280; Mud Pump: See Below; Engine: 8V92T; Mounted On: 3-Axle Trailer; Tools/Options: Shopbuilt: Built in the Early 1980's, Pulldowns in Mast, 18" GEFCO/Speedstar Heavy Table, Power to Rear Axle is Powered by the8V92T with Allison Transmission & Drop Box (live, steerable axles on the trailer), Can Drive Rear End. Mast is 63' 6" and 6' Wide, 4" 250 Wall, 6 Lines, Trip & Kelly, 3" King Swivel, 5-1/2" Hex Kelly, Drums have 10 36 Dual Brakes, 18" Triple Disc Air Clutches, Air Clutches on Drawworks & Rotary Table. Can be Sold as a Package that Includes a Trailer Mounted 7-1/4" X 14" Gaso Mud Pump Powered by a 318 Detroit (other mud pumps available). 3,000' of 4.5" X-Hole Drill Pipe & Collars with Tandem Trailer. 3-Axle Trailer Drill is mounted on has 11 24 5 Bud Wheels, Trailer would need new tires if pulled a long distance. Condition: Last Drilled 3 Years Ago
Rotary S - SRS #4401
DESCRIPTION: 2001, Schramm; Model: T450WS; Compressor: Sullair 900/350 w/ Clutch; Mud Pump: Mission Magnum; Engine: CAT 3206; Mounted On: 2001 IHC 6X4; Truck Engine Make: Diesel; Tools/Options: Schramm T450WS Year: 2001: Pullback 30,000#, Pullback, 17,000# Pulldown. Dual Tophead Motors, 28'6" Mast Travel. Four Outriggers, Braden PD15 Winch, 15,000# Capacity. 10-Rod Carousel, Rig Holds 480' of 3-1/2" X 2-7/8" X 20' Drill Pipe, Hydraulic Table and Break-out Wrench (48" but cant take 60"), 205 Gallon Fuel Tank, Hammer & Stabilizer Holder, Sliding Tophead, Water Injection, Pipe Rack, Jib Boom with Hydraulic Swing, No Sandline. Truck has 56,000# GVWR, 16,000# Front, 46,000# Rears. CAT 3206 Deck Engine Rebuilt (Sept 2024),Tophead also Rebuilt (Nov. 2024). Currently having a New Mast Installed. Service Records Available. Compact Drill Good for Geothermal and Mineral Exploration. Truck Odometer Reads 003,300.4 Hours. Compressor Hours Unknown. Truck Odometer Miles 077,103.9. No Rod & Tooling Included. Currently having a new mast installed.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
Rotary S - SRS #4014
DESCRIPTION: Speedstar; Model: SS-22; Mud Pump: GD FXO 7-1/4" X 10"; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: N 14 Red Top 460 HP Cummins; Tires: Near New; Condition: Good; Tools/Options: Speedstar SS-22: Capable of Range III Casing up to 44'. NEW 10" GD Retractable Rotary Table, NEW Rotary Transmission with 5 Forward & 1 Reverse, Bean 4-Cylinder Injection Pump, Custom Built 56' Heavy Duty 3" Square Tubing Mast with Huge Hydraulically Folding Racking Board & Heavy Duty Substructure. Drill is Set Up to Run 30' Drill Pipe, 36' X 6" Hex Kelly with Retract, 3" Little Giant Swivel Recently Rebuilt, New Spicer PTO with Front & Rear Air Actuators on Driller's Panel, Main Clutch Control below Driller's Panel, Completely Rebuilt SS-22 Double Drum Brake Drawworks with LeBus Grooving, 18" Air Clutches & 3rd Sandline Drum, Hydromatic Brake, 2 Huge Traveling Blocks, NEW Hydraulic Pump, (4) Hydraulic Jacks & (2) Screw Jacks under Rotary Table Frame, Planetary Pulldown, Hydraulic Spinning Chain, Folding Drill Floor, NEW LED Lights throughout Rig. Carrier has a Fuller Road Ranger Transmission. Engine has a new PCM & Injector Pump, Rear Air over Electronic 2-Point Throttle Control, All 12 Tires are Near New, Driven < 500 Miles. Includes approx. 2,100' of 3.5" X 30' Drill Pipe with 3.5" IF Tool Joints & (6) Drill Collars, Slips, Screw Plug & Bit Subs. Un-used Weight Indicator with 2 Load Cells Available for an Extra Cost (not mounted on rig). Almost Everything has been Rebuilt on this Rig from July 201 to Present. Heavy Duty Rig with a Big Mud Pump and Small Footprint..
Rotary S - SRS #4121
DESCRIPTION: 1975, Schramm; Model: T64HB; Compressor: 400/200 (to be confirmed); Mud Pump: 5X6; Engine: 318 Detroit; Mounted On: 1975 GMC; Truck Engine Make: Gas; Condition: One Owner; Tools/Options: Schramm T64HB Year: 1975: One Owner Drill! Compressor CFM/psi to be confirmed, could be 425/250 or 450/250. Water Injection, Oiler, Carousel hold 5 Rods and more can be hauled in the Pipe Rack. Engine was Overhauled in 2005, had Injection Work done to it. Approx. 500' of pipe and bits available for an extra cost. Last job was 2 years ago but can be started and run to show. Also has a 750/350 2-Wheel,Trailer Mounted Compressor available for an extra cost.
Rotary S - SRS #4061
DESCRIPTION: Speedstar; Model: SS 15 II; Compressor: LeRoi 250; Mud Pump: GD 5X6; Engine: PTO; Mounted On: Ford 9000; Truck Engine Make: CAT 3406; Condition: OFF MARKET; Tools/Options: Speedstar SS 15 II : Compressor is either a Sullair or LeRoi. 8" Retractable Table, Air Clutches, 35' Mast, 60,000# Pullback. Miles Unknown, Odometer Turns while Drilling. Truck has a 13-Speed Eaton Transmission, Good Rig, Motor is Strong. There is approx. 360' of Drill Pipe available, Amount to be Confirmed. OFF MARKET
Rotary S - SRS #3400
DESCRIPTION: 1976, Speedstar; Model: SS-22; Compressor: LeRoi 256S2 445/250; Mud Pump: GD 5-1/2" X 8; Engine: PTO; Mounted On: 1976 3-Axle CCC; Truck Engine Make: Cummins; Condition: Good; Tools/Options: Speedstar SS-22 (1976): Hydraulic 10" Retractable Table, 34' Mast, 3-1/2" Fluted Kelly, 2" Little Giant Swivel, Double Drum with Sandline, Mechanical and Air Clutches, Engine Preheater.
Rotary S - SRS #3929
DESCRIPTION: 1988, Speedstar; Model: SS 700; Compressor: 700/250; Mud Pump: 3X4X13; Engine: PTO; Mounted On: IHC; Truck Engine Make: Cummins; Condition: Working Drill; Tools/Options: Speedstar SS700 Year: 1988: Includes Hammer. TEMPORARILY OFF MARKET, PUT BACK TO WORK.
Rotary S - SRS #3856
DESCRIPTION: 1971, Speedstar; Model: SS 15; Compressor: LeRoi 256S2; Engine: PTO; Mounted On: 1971 IHC; Truck Engine Make: Detroit 8V71 318 HP; Condition: Clean; Tools/Options: Speedstar SS 15 Year: 1971: 8-1/2" Retractable Rotary Table, Four-Part Main Line, 60,000# Pullback, 25,000# Pulldown, 6,000# Sand Reel, 2" Plumbing, Rod Box set up for 180' of 4.5" X 15' Drill Pipe, 10 GPM 2-cyl. Water Injection System, 12-Volt Electric Hammer Oiler, (3) Hydraulic Jacks, Eaton 8LL Manual Transmission. Truck had an in-frame rebuild. Includes 315' of 4.5" X 15' Flush Joint Drill Pipe, 5" X 15' Flush Joint Drill Collar and a Sandvik RH 550W Hammer, Misc. Subs, Drill Bits, Pipe Wrenches and other Drilling tools.
Rotary S - SRS #2152
DESCRIPTION: 1987, Speedstar; Model: SQD 275; Compressor: 300/200; Mud Pump: 5X6-1/4 Failing; Engine: PTO; Mounted On: 1987 International 1954; Truck Engine Make: DT 466; Condition: TEMPORARILY OFF MARKET, CURRENTLY DRILLING; Tools/Options: Speedstar SQD 275 Year: 1987: Single Rod Loader. Piston Mud Pump, Hydraulic Pump for Mud Pump Completely Gone Through, 21,000# Pullback. Set up to Run 15' or 20' Steel. Includes 20 Joints of 15' Pipe. Unit has approx. 275,000 Drill/Drive Miles on Odometer and aprox 4,900 Hours. TEMPORARILY OFF MARKET
Rotary S - SRS #3684
DESCRIPTION: 1978, Schramm; Model: T64; Mounted On: Kenworth; Truck Engine Make: Detroit 8V71; Tools/Options: Schram T64: Casing Hammer Drill, No Rod Box. Truck in Good Condition, has a Jake Brake. Has an Adaptor to Drive 12" Casing. Includes a pipe Trailer and approx. 400' of 4.5" Drill Pipe.
Rotary S - SRS #3647
DESCRIPTION: 1996, Simco ; Model: WS 5000; Compressor: 435/200 Sullair; Mud Pump: 4X3 MCM - Low Hours; Engine: PTO; Mounted On: 1995 L8000; Truck Engine Make: 300 HP Cummins; Condition: Good Working Drill; Tools/Options: Simco WS 5000 Year: 1996: Turn Key Geothermal Drill Includes Everything you need to Drill, Install Loops and Grout. 12,000# Main Winch with Automatic Break, 2,500# Auxiliary Winch, Water Injection Pump, Hydraulic Retractable Table with Flat Wrench, New Top Feed Water Swivel, Four Hydraulic Leveling Jacks, Rod Box with Rod Slide and Stabilizer Holder, Catwalk on Box Side, Hydraulic Breakout Wrench, One Large and Two Small Tool Boxes. Truck has an 8-Speed Transmission. Mud pump is Two Years Old and has Low Hours. Includes approx. 300' - 400' of 2-7/8" FEDP Drill Pipe Purchased New in 2017. Also Includes a Loop reel and 450' of 1" Tremie Line, Cement Mixer with Moyno Pump, 14' Enclosed Support Trailer with all the tooling you Need to Drill.
Rotary S - SRS #3556
DESCRIPTION: 1976, Speedstar; Model: SS-15-THH; Compressor: LeRoi 252 S2C; Mud Pump: See Below; Engine: PTO; Mounted On: CCC; Truck Engine Make: 350 Cummins; Condition: PRICE REDUCED; Tools/Options: 40' Mast, 3-Line Machine with an Auxiliary Line, BJ Tongs, 4-Cylinder Bean Injection Pump, Auto Oiler. A Centrifugal Mud Pump is Available, run by a Gas Engine, Set Up with PTO, Could be Mounted on Deck. Engine and Compressor have < 550 Hours on them. Carrier has a 13-Speed Transmission. Pipe and Misc. Tooling Available
Rotary S - SRS #2951
DESCRIPTION: 2001, Simco; Model: 9100; Compressor: None; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2001 IHC 4900; Truck Engine Make: 530 HP; Tires: New; Condition: Good - Operational - Working; Tools/Options: Simco 9100: Tophead Drill, Bean Water Injection Pump, Sandreel, (2) Winches, Break-out Wrench. (2) Front & (2) Rear Jacks. Truck had a New Engine put in at 13,793 Miles, Current Miles are approx. 14,575. 400' of 3-1/2" X 20' Drill Rod on Rig, another 400' Available. OFF MARKET
Rotary S - SRS #2648
DESCRIPTION: 1992, Schramm; Model: T 450 H; Compressor: 750/300 with Clutch; Mud Pump: None; Engine: 692 Detroit; Mounted On: 1992 Ford L8000; Truck Engine Make: Inline 6-Cylinder; Condition: OFF MARKET; Tools/Options: Schramm T 450 H (1992): Rig has 38,000# Pullback, approx. 3896 Hours, derrick is 22' above Table, (2' of Working Space), (3) Jacks, Banger 612 Casing Hammer, Pipe Rack, No Carousel. Will Include approx. 200' of 4.5" X 20' X 3.5" Regular Thread Drill Rod, another 800' +/- is available for an Extra Cost. Also Available for an Extra Cost are Various Size Hammers, Bits, Subs and misc. Tooling. Truck has approx. 48,000 Miles on it. OFF MARKET
Rotary S - SRS #2856
DESCRIPTION: Sonic AMS; Model: CRS-17C; Compressor: N/A; Mud Pump: N/A; Engine: PTO; Mounted On: Rubber Track Crawler; Truck Engine Make: John Deere 4045T Diesel; Condition: TEMPORARILY OFF MARKET; Tools/Options: 2010 or 2011 AMS Sonic CRS-17C: Dual Rotation/Sonic Drilling, 293 Head, 2-6" Casing/Rod to 200', 22,400#/lbf Oscillator Output, 1,475 ft-lb Rotary Torque, 205 RPM Maximum Rotation Speed, 13,000# Pullback, Cathead Hoist and 3,000# Hydraulic Hoist, (4) Hydraulic Jacks. Carrier has 4.6 PSI Ground Pressure. 2,931 Rig Hours, 395 Hours on Head. Includes approx. 200' of Tooling consisting of 7.5" Casing, 5.5" Casing and 3" Rods.
Rotary S - SRS #2758
DESCRIPTION: 1980's, Schramm; Model: T 64; Compressor: 750/350; Mud Pump: N/A; Engine: 8V92; Mounted On: 1989 International; Truck Engine Make: 300 Cummins; Tires: Good; Tools/Options: Schramm T 64 Year: 80's: Bean Water Injection, Hammer Oiler, 4-Rod Carousel, approx. 800' of 2-7/8" IF Thread Drill Rod, 6" & 8" Hammers Stabilizer, Bits, Welder, Cutting Torches, Diaphragm Mud Pump and Extra Parts can be Included for an Extra Cost. Tophead Good, King Swivel, Approx. 3,560 Hours on Deck Engine (installed approx. 2012). King Swivel, New Clutch, Torque Dampener, New Seals in Turbo, New Radiators and new Pumps. Truck has a 13-Speed Transmission. Can be sold with SRS #2759 for a package price.
Rotary S - SRS #2733
DESCRIPTION: 2010, Sonic; Model: SDC-425; Compressor: N/A; Mud Pump: N/A; Engine: PTO; Mounted On: Tracks; Truck Engine Make: CAT C6.6; Tools/Options: Sonic SDC-425: Versa Drill (2) Motor Top Drive (same as a Versa Drill V-100 Top Drive). 18 GPM Water Pump, CAT 312 Undercarriage, Rod Handling System. Capable of carrying 700' of 2-7/8" X 20' Drill Rod on Board. Rexroth Valves, Pumps and Controls. Break-Out Table up to 8". 3,500 Hours on Rig. This rig does not have a Sonic Vibratory Top Drive.
Rotary S - SRS #2707
DESCRIPTION: 2005, CS Sonic ; Compressor: N/A; Mud Pump: Moyno 3L6; Engine: Cummins QSB4.5P; Mounted On: 2005 Nissan UD 2600; Truck Engine Make: Diesel; Condition: Good; Tools/Options: CS Sonic: Sonic Head (28,000#), Rotary Motor has 1,400 ft/lbs. of Torque and 1-120 rpm. S-27 Feed System is Equipped with a Motor & Double Chain System - 7,000# Retract & 7,000# Pulldown, 10' Stroke, Rapid Retract - 200 ft/min. Mast is approx. 16' - 20'. Mast, Feed Frame, Hydraulic System is Powered by Twin Variable Displacement Load Sensing Pumps. (Sonic & Rotation Driven by one Pump, Feed & Auxiliary Functions are Driven the Second Pump). 10 Micron Hydraulic Oil Filter, Hydraulic Oil Cooler both Mounted on the Intake Side of the Power Unit. Electronic Deck Engine California Emissions Cert. through 2010. Combination Water Tank & Tool Storage, Manual Break-out Table & Break-out Wrench, Crown Block & Sheave Assembly, Hydraulic Steam Cleaning Station & Grout Plant, Deck Walkways, DOT Lighting. Casing Rack, Moyno 3L6 Pump, Under Deck Tool Storage, Rod Box. Working Order. GP 63 (2"), GP 88 (3") and GP 100 (4") Tooling & Accessories, 3 Meter Lengths (approx. 10'). 1,723 Hours on the Deck Engine and 32,269 Miles on the Truck Engine. Was used for Injection Work, Soil Sampling and had drilled with it up to 100'. Good Drill for Work In Sandy Soils. Drill Rod Vibrates but does not Vibrate & Turn at the Same Time.
Rotary S - SRS #2494
DESCRIPTION: NOV/OEM Certified in 1974, SKYTOP BREWSTER - Reconditioned; Model: TR-800 900 HP; Compressor: None; Mud Pump: None; Engine: (2) Detroit 60 Series Engines Each Rated at 475 HP @ 2100 RPM; Mounted On: 3-Axle 100,000# Trailer; Tools/Options: Reconditioned Skytop Brewster TR-800, 900 HP Remanufactured 1974 TR-800. H14610-38 Reconditioned Drawworks, Twin Disc Clutch, 46 X 10 Brakes, New Drum Grooved for 1-1/8" Drill Line (3,000' of 1-1/8" 6X19 Line). Twin Reconditioned Sand Line Drum - Twin Disc Model PO-224, 38 X 8 Brakes including 15,000' of 9/16" New Sandline. Hydromatic Water Assist Brake. Factory Allison 5-speed Transmission. 115', Category 4 Repair, OEM Certified, 410,000# Telescoping 8-Line Mast with an Operating Hook Load of 388,000#, 55', 58', or 70', Racking Board Height with a Capacity of 10,080' - 4-1/2" Drill Pipe Doubles, Crownomatic Emergency Stop System. (Includes Stand Pipe with Gooseneck Union, Gates Valves, Derrick Escape with Wireline, clamps & Anchor. New, NOV Certified Crown Block Set up for an 8-Line String Up, (5) 1-1/8" Grooved Sheaves Mounted on Roller Bearings & New Crownomatic. Reconditioned Dead Line Anchor. Trailer has New Suspension, Hydraulic Controls, Drillers Console, Telescoping Cylinders, Raising Cylinders, Mast Locking Cylinder, Hydraulic Jack Cylinders, (2) Manual Jacks, Jack Stands.. Condition: Reconditioned NOV/OEM Cert.
Rotary S - SRS #1981
DESCRIPTION: Sanderson Cyclone; Model: 200R; Compressor: None; Mud Pump: None; Engine: Detroit 8V71; Mounted On: Int. Paystar 5000 AWD; Truck Engine Make: 3208 CAT; Tools/Options: PARTS RIG 30' X 4-1/2" Kelly, No Turntable
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |