Rotary G
Rotary G - SRS #4517
DESCRIPTION: 2023, GEFCO; Model: 30K; Compressor: 1050/350; Mud Pump: 3" Wilden; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: Cummins 565 HP; Condition: Great; Tools/Options: GEFCO 30K Year: 2023: Holds 6 Rods in the Carousel and 15 in the Rod Box. Single Rod Loader, Rod Spinner, Hammer Holder, Foremost Shock Sub. Some Warranty Left out of the 5 Year Warranty. Rod that drill can hold is included along with a used 6" QL6 Hammer and an 8" Rebuilt Hammer with 8-3/4" Hammer Bit and a 8-3/4" Roller Bit with 15' Sub, 5-7/8" Roller Bit for Cleanout, Stabilizers, Bit Breakers, Slips, Pipe Lifters, 10-12 Bags of Mud. Also Includes a Water Truck (2) 20' Hoses, No Fuel Tank on the Truck but has a 120 Gallon Tank with an Electric Pump that could be Included. Rig is Set Up to Run 4.5" X 20' X 2-7/8" Drill Pipe. Hub Odometer Currently Reads 10,977 Miles, Total Rig Hours - 2,313 and Current Compressor Hours are 1,222.
Rotary G - SRS #4502
DESCRIPTION: 1982, Gardner Denver; Model: 2000; Mud Pump: Gardner Denver 7-1/2" X 10"; Mounted On: Trailer; Condition: SOLD; Tools/Options: Gardner Denver 2000 Year: 1982: Everything Repacked and Serviced, Drill has been Refurbished. SOLD
Rotary G - SRS #4433
DESCRIPTION: 2016, GEFCO; Model: SS-22 RC HD; Compressor: DR 500/200; Mud Pump: 6X5X14 National; Engine: PTO; Mounted On: 2015 Peterbilt 367; Truck Engine Make: Cummins ISX15 525 HP; Tools/Options: GEFCO SS-22 RC HD Year: 2016: Telescoping Jacks, Original Build Sheet Shows 18" Failing 150 Ton Rotary Table, 6" Western Rubber Swivel, 6" Western Rubber Air Side Inlet, 23' Kelly Bar, 7" Dual Outside Air Flange Ends, 4-Part Kelly Line with14" Block, 4-Part Pipe Line with 14" Block, Sandline, 15' Mast Extension, 6" Swivel. Truck Odometer Reads 14,854 Miles and 5,206 Hours. Compressor needs a new air end. Some Flange Connection Outside Air Drill Pipe Available for an Extra Cost.
Rotary G - SRS #4393
DESCRIPTION: 2018/19, GEFCO; Model: 40K; Compressor: Sullair 1000/350; Mud Pump: Plumbed; Engine: PTO; Mounted On: 2019 Peterbilt 367 6X4; Truck Engine Make: Cummins 565 HP (recently rebuilt); Condition: Good Working Drill; Tools/Options: GEFCO 40K Year: 2019: Newly Rebuilt Engine (Injectors, Turbo, Oil Cooler), Truck Brake Compressor also Rebuilt. Rig is set up to Run 4.5" X 20' Flush Joint Drill Pipe with 2-7/8" IF Tool Joints and a Holte 350 Casing Hammer. 25K Pulldown, 40K Pullback. 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator, 25,000# Single Line Hydraulic Main Winch over the Jib. Hydraulic Rod Spinner, Modified 60" Breakout Wrench, Auxiliary Winch Mount & Hydraulics (rig has 2 winches, cable recently replaced), 3-Speed Tophead, 15 Piece Rod Box, 6-Rod Carousel, Hammer Holder. Upgraded Joysticks (5-Volt Electric Upgrade), Compressor has approx. 2,300 Hours, approx. 6,000 Total Frame Hours, < 500 Hours on the Newly Rebuilt Engine.. Truck has 22,000# Front Axle, 46,000# Rears, 18-Speed Fuller Transmission. 400' of used pipe included.. Condition: Working Drill
Rotary G - SRS #3914
DESCRIPTION: 1975, Gardner Denver; Model: 2000; Mud Pump: GD 7-1/2" X 10"; Engine: PTO; Mounted On: 4-Axle Crane Carrier; Truck Engine Make: 400 Cummins; Tools/Options: Gardner Denver 2000 Year: 1975: 58' Mast, 10" Retractable Rotary Table, Air Clutches, Two Drum Machine, No Sandline, No Rod Rack, 4-1/4" or 4-1/2" X 38' Hex Kelly (needs confirmed), Rig is set up to run 30' Rod. Has a Large Gardner Denver Swivel that has been Rebuilt, 2 Wells since. Has a Winch on the Side for Oil Field Dogs. Also Includes 810' of 5" X 30' Drill Rod with 3-1/2" IF Threads (used on 6 wells) and a Rod Trailer that was Purchased New and has < 300 Miles on it. Can be sold without rod.
Rotary G - SRS #1967
DESCRIPTION: Gardner Denver; Model: 3000; Mud Pump: 7-1/2 X 10 GD; Engine: (2) Detroit 6V71 Rebuilt in 2019; Mounted On: 6 Axle CCC; Truck Engine Make: 871T; Condition: Excellent; Tools/Options: Gardner Denver 3000 : Operating Daily! Re-manufactured in 2006. Double Drum with Sandline - 3 Drum line (no need for rathole), Kelly Track in the Derrick. Fast Drilling, Easy Removeable Table. 60' Racking Board. 1 deck engine drives the mud pump and the other engine drives the Drawworks. 70' mast, telescopes to 97', rated @ 250,000# with 100 ton Webb traveling block with 1" cables. 4" King swivel with 4-1/2" IF X 37' fluted Kelly. 18" Brewster Skytop oilfield table. (2) BJ breakout tongs, air clutches, (6) hydraulic jacks (4) screw jacks, 50 ton McKissick block (Kelly), operators platform. 4-5 yrs. old since completely rebuilt from ground up. Includes all the standards - elevators, slips, bushings. Has set 36" Casing, Table Lifts Out with Sling. Deck Engines Rebuilt in 2019. All 4 Rear Axles Pull.
Rotary G - SRS #4515
DESCRIPTION: 2020, GEFCO; Model: 40K; Compressor: 1070/350; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: Peterbilt; Truck Engine Make: Cummins ISX 605 HP; Condition: Great; Tools/Options: GEFCO 40K Year: 2020: 1,038 Hours on Compressor, 5,374 Hours on the Engine.
Rotary G - SRS #4132
DESCRIPTION: Gardner Denver; Model: 1500; Mud Pump: 5X10; Mounted On: 1976 +/- 4-Axle CCC; Truck Engine Make: Cummins; Condition: Being Reconditioned; Tools/Options: Gardner Denver 1500: Big Kelly (4-1/2" - 5" to be confirmed), Mast is at Least 38', Rig can Handle 34' Pipe Retractable 10" Table, Leveling Jacks, Air Clutches on Drawworks, Sand Reel and Air Clutches.
Rotary G - SRS #4454
DESCRIPTION: Gardner Denver; Model: 1000 HD; Mud Pump: 5X6 Piston; Mounted On: 2004 IHC 7400; Truck Engine Make: International DT 530; Tools/Options: Gardner Denver 1000 HD: 4-Part Kelly Line, 3-Part Trip Line, 3-3/4" Fluted Kelly approx. 5 Years Old. Recently Installed 7-1/2" Retractable Table Rebuilt when Installed. Mud Pump Installed in approx. 2023, had a Complete Rebuild at that time. Mud Side Rebuilt once Since. Manual clutches on Drawworks and Mud Pump. Double Frame Truck, Complete Rebuild on Engine < 50 Hours ago. Brand New Clutch, and Tires < 2000 Miles Since. Eaton fuller Transmission. Walking Beam and Rear Brakes have < 1,000 Miles. Includes 380' - 400' of 3.5" Drill Rod with 2-3/8" IF Thread, No Subs..
Rotary G - SRS #4443
DESCRIPTION: 1990, Gill Beetle; Mounted On: Tracks; Tools/Options: Gill Beetle Year: 1990: Tophead Drive. Includes 200' of Aluminum Drill Rod and 100' of Steel Drill Rod. Carousel holds 6 Rods. IR Side Air Available for an extra cost.
Rotary G - SRS #4442
DESCRIPTION: Geo Drill; Compressor: 900/350 Sullair; Mounted On: 2005 Sterling; Tools/Options: Geo Drill: 15-Rod Carousel. Includes 300' of 20' 3.5" Regular Drill Rod.
Rotary G - SRS #4434
DESCRIPTION: 2014, Geoprobe; Model: 7822DT; Engine: PTO; Mounted On: Tracks; Truck Engine Make: 4-Cylinder Diesel; Condition: Ready to Work; Tools/Options: Geoprobe 7822DT Year: 2014: Auto Hammer, Breakout Table, Rod Clamp, Breakout Wrench, Two Winches. Rotary, Auger, Core and SPT Sampling Capabilities. Low Hours, approx 6,680. No Tooling Included.
Rotary G - SRS #4173
DESCRIPTION: Gardner Denver; Model: 1400; Compressor: GD 667; Mud Pump: 5X6; Mounted On: 1999 Kenworth; Tools/Options: Gardner Denver 1400 OFF MARKET
Rotary G - SRS #4124
DESCRIPTION: Tools/Options: Land Rig: 700 Drawworks similar to a GD 500, Single Drum Mechanical 700 HP 1-1/8" Drill Line, Foster Makeup and Breakout. Cat heads with (2) CAT C15, 540 HP Engines, C195-80 Torque Converters on an Inline Compound 350 Air Compressor, Eaton 424 Water Cooled Brake. 128T'X15'6"W 450,000# Single Hook Load Cantilever Mast with (5) 16" Sheaves (1) 20" Fast Line Sheave 4" Stand Pipe with Rotary Hose Racking Board Tong Line and Weights and Derrick Stand. 17' Floor Height Substructure, 450,000# Setback Sub 21' Wide X 50' Long Swingout Dog House Stands on 5' Wide X 5'T Pony Subs (pony subs can be removed to make a 12' floor height). (3) Ingersoll Rand Air Winches, (2) Electric/Hydraulic Wireline Machines. 20-1/2" RCZP Rotary Table, Artic 250 Ton Shorty Blocks, (5) 1-1/8" Sheaves with Elevator Links. 9' High X 10' Wide X 16' Long Doghouse Mounted on a 9' High X 10' Wide X 20' Long Skid. (2) 5' Wide X 42" X 30' Long Catwalks. Brake Cooling Skid with Brake Water Tank Heat Exchanger and Centrifugal Pumps. 48' Long Generator House with Switch Gear and (2) Generator Bays (no generators). (1) Maxum M1600 Triplex Mud Pump PBA CAT 3512B Engine, (1) Gold Horse 1300 Triplex Mud Pump PBA CAT 3512B Engine. 6' T X 10' Wide X 40' Long, 3 Compartment Mud Pit with Two Mud Agitators and 2 Shale Shakers, 6'T X 10' Wide X 40' Long 3 Compartment Mud Pit (3) Agitators, Mud Hopper and Centrifugal Pumps. 8' Wide X 30' Long Mud House with Stands. 500 bbl. Water Tank, 8' X 33' with 4 Compartment Lubester. 500 bbl. Water Tank 8' X 33' with Centrifugal Pumps. 8' X 34' Water Tank. 10,000 Gallon Diesel Tank with 2 Pumps and Filters. 5 Compartment Lubester. 13-5/8" Shaffer Double BOP, 5,000 psi with 13-4/8" Annular. 13-5/8" Shaffer Double BOP, 5,000 psi with 13-5/8" Annular & Drilling Spool. Scarbrough, 6 Station Closing Unit with Electric & Pneumatic Pumps, 10 Bottle with Stainless Control Lines. 5,000 psi Skid Mounted Choke Manifold, (7) Suite Cases, Artic T-200 Swivel, 4-1/4" X 39' Kelly with Shuck and Rat Hole, Martin Decker Weight Indicator Panel. Misc. Tooling, Manual, Tongs, Mud Bucket, Elevators, Elevator Links, Crossover Subs, Bit Breakers, Several Pieces of 10" Steel Flow Long. Was Drilling 8,000' Gas Wells During COVID then Parked.
Rotary G - SRS #3037
DESCRIPTION: 1980, Gardner Denver; Model: 1700; Compressor: N/A; Mud Pump: 5-1/2" X 8"; Engine: PTO; Mounted On: 2002 Western Star; Truck Engine Make: CAT C12; Condition: OFF MARKET PUT BACK TO WORK; Tools/Options: Gardner Denver 1700: OFF MARKET PUT BACK TO WORK. Approx. 1406 Hours, Truck has 380,000 miles on it. Miles are not actual, the computer reads the transmission the whole time it's spinning so when the rig is in rig gear the truck is reading miles. The drawworks are rated at 15,000# single line and the rig is set up to run up to 4 lines. Recommended operating is approx. 45,000#. 44' Mast that is Flanged for an Extension and is Wider to Accommodate Larger Casing. Rig Could Easily do Large Diameter Wells or RC. Mud Pump has A New Fluid End and New Clutch. New 2" Swivel and 23' X 3-3/4" Fluted Kelly, Air Clutches. 10-Speed Rotary Transmission & a 10" (recently rebuilt - 2022) Retractable Rotary Table . Price includes a new table. New Rotary Clutch, Hydraulically Driven Sand Reel, Run with Air Clutch & Brake. Tandem-Tandem Truck with a 13-Speed Transmission and a Spicer 792 Gear Box PTO. Drill Rod available for an Extra Cost.
Rotary G - SRS #3916
DESCRIPTION: 1980's, Gardner Denver; Model: 3000; Mud Pump: 7-1/4" X 14" Gardner Denver; Engine: CAT 3406B; Mounted On: 3-Axle Trailer; Tools/Options: Gardner Denver 3000 Year: 1980's: 1980's Drill, 18" Gardner Denver Rotary Table, 96' Free Standing Mast, Single Drum 8-Lines, Rat Hole Rig, 4-1/4" Square Kelly, Includes 130 Joints of X-Hole Drill Pipe, 8 Collars, Mud Boat, 3 Pipe Tubs.
Rotary G - SRS #3904
DESCRIPTION: 2015, GEFCO; Model: Stardrill 300 HD; Compressor: 1000/350 Atlas Copco Rotary Screw; Mud Pump: GD FXG 5X6 Duplex; Engine: PTO; Mounted On: unmounted; Tools/Options: GEFCO Stardrill 300HD Year: 2015 : Will need a Deck Engine or PTO, Main Gearbox is Missing on Rig along with some Hydraulic Pumps. 12" Square Tube Mast has a Rated Working Capacity of 60,000#, Free Height under Jib is 36'6". 24,000# Pullback Capacity, Hinged Breakout Table, Power Holding Wrench, Adjustable Jib Boom with 2 Pulleys for Winch Cable Mounted at the Top of the Mast Provided with 2 Hydraulic Cylinders for Jib Extension & Rotation (allows for tripping of dual Pipes), 3-Cylinder Water Injection Pump, 7-Gallon Hammer Oiler, Single Rod Loader, Hydraulic Winch, Breakout Wrench, Pipe Spinner, Four Hydraulic Leveling Jacks, 26' of Tophead Travel, 15-3/4" Table Opening. Direct Circulation Rig with Mud & Air Drilling Applications.
Rotary G - SRS #3549
DESCRIPTION: Geospace; Model: 750; Mud Pump: Gardner Denver 5X6; Engine: PTO; Mounted On: Buggy; Truck Engine Make: Detroit 453; Tools/Options: Geospace 750: 300' of Sandline, 2-Speed Transfer Case. Geothermal Drill.
Rotary G - SRS #3544
DESCRIPTION: Gus Pech; Model: Brat 22R; Mud Pump: Gardner Denver; Mounted On: 1987 Ford FT 8000; Truck Engine Make: Cummins 6BTA5.9; Condition: OFF MARKET; Tools/Options: Gus Pech Brat 22R: Aardvark Casing Hammer. Includes 390' of 2-7/8" Near New Drill Rod, also includes some bits.. OFF MARKET
Rotary G - SRS #2786
DESCRIPTION: 1972, Gardner Denver; Model: 14W; Compressor: See Below; Mud Pump: N/A; Engine: PTO; Mounted On: 1972 CCC; Truck Engine Make: 350 Cummins Big Cam REMANUFACTURED IN MAY 2015 BY CUMMINS; Condition: Fair to Average; Tools/Options: Gardner Denver 14W (1972): Hours and Miles Unknown, 39' Mast, Air Clutches - 4-Speed Transmission, 4-1/2" X 25' Fluted Kelly, Rod Rack, Newer Sliding Driveshaft, all Switched over to 18-10. , Rebuilt Transfer Case, Rebuilt Drawworks, Rebuilt 2" Little Giant Swivel, Rebuilt 10" Retractable Table. Air Shift Spicer 784 PTO, Hydraulic Chain Pulldown. Cummins Big Cam Remanufactured in May 2015 by Cummins, 13-Speed Transmission. New Injector Pump, New Truck Air Compressor. Painted in 2013. Lots of Spare Parts. Rig is in good Condition, Working Daily. Includes 300' of 4-1/2" XX 20' Drill Rod & a 6" Hammer. Also has a Never Used GD 1200/150 Screw Air End Available. Some Rust on Doors & Cab Floor. Sullair 750/250 w/ Clutch has been removed. Air Powered Underdrive Clutches for a Mud Pump and Air Compressor are still intact. Rebuilt Compressor & Clutch in 2012. All work was done a few years ago, last time rig drilled a hole was in 2016..
Rotary G - SRS #3399
DESCRIPTION: Gardner Denver; Model: 15W; Compressor: GD WEJ 650/250 with Blower; Mud Pump: GD 6X8; Engine: PTO; Mounted On: 1973 4-Axle CCC; Truck Engine Make: 350 Cummins; Tools/Options: Gardner Denver 15W: Compressor has Issues. 3-Drum Drawworks with Air Clutches, 38' Mast, 10" Retractable Table, Hydraulic Pulldowns, 4-1/2" X 24' Fluted Kelly, (3) Hydraulic Leveling Jacks, Side Pipe Rack, Platforms, New Swivel and New Mast Cylinders. Rig Overhauled in 2010 Including Diesel Engine.
Rotary G - SRS #3019
DESCRIPTION: 1974, Gardner Denver; Model: 3000; Compressor: None; Mud Pump: GD 7-1/4" X 14"; Engine: Detroit & CAT; Mounted On: 3-Axle Trailer; Tools/Options: 85' Telescoping Mast, 17-1/4" Table Opening on Rotary Table, Double Drum, Main Line and Sand Line, SW 75 Swivel, 6.55" Kelly, Kelly Bushing, Manual Clutches on Drawworks, Recently Painted, Ready to Work. Mud Pumps Mounted on a Skid/Platform.
Rotary G - SRS #3018
DESCRIPTION: 1982, Gardner Denver; Model: 3000; Compressor: None; Mud Pump: GD 7-1/4" X 14"; Engine: Detroit & CAT; Mounted On: 3-Axle Trailer; Tools/Options: 85' Telescoping Mast, Single Drum, Manual Clutches on Drawworks, 17-1/4" Opening on Rotary Table, SW 100 Swivel, 6.55" Kelly, Kelly Bushing, Drawworks, Recently Painted, Ready to Work. Mud Pumps Mounted on a Skid/Platform.
Rotary G - SRS #2681
DESCRIPTION: 1993, Gus Pech; Model: GP-1100C; Compressor: N/A; Mud Pump: 2X3X13 Hydraulic Centrifugal; Engine: PTO; Mounted On: ATV Transquipment; Truck Engine Make: Cummins Diesel; Tools/Options: Gus Pech Brat GP-1100C: 12" Style Mast, 2-Way Crosstop Head Slide (rack & Pinion Actuated), Planetary, Hydrostatic Tophead Drive 88-160 RPM, 11,000# ft. lbs. Torque, 14' Stroke, Hydraulic Actuated Pulldown - 24,537# & 2-Speed Retract - 18,412#, Auger & Coring Heads, Pulldown & Holdback Feed Control System. Dual Hydraulic Pump Drive System, Hydrostatic Control, Oil Cooling System, Tachometer, Standard Lighting, Tower tool Carrier for Transportation, Stationary Foot with Hydraulic Tool Clamp, (4) Outriggers - 5" X 30" X 3" (Front & Rear). Engine Friction Throttle, Operator Foot Stand, Transfer Case Drive System. Hydraulic Slide Base & Jib Boom with Extension. Dual Motor/Spindle Coring Attachment (750 RPM/1186 ft. lbs. 4,000# GP Winch with Headache Ball, 3/8" Cable with Swivel Hook. 12,000# Pullmaster Winch with Rapid Reverse - 1/2" Cable with Bearing Swivel. Rupe Auto Stroker Hoist with 1,000# Winch & Cable. 3L6 Moyno with Hydraulic Motor, Rod Rack with Hammer Holder, Swing Around Auger Rack, Cathead, Steel 200 Gallon Water Tank, 300 Gallon Mud Pit, (2) Tool Boxes. Break-out Wrench, Drill Rod Adaptor Attachment & Busing, Auger Glide Bushing. IF-DC Side Inlet Swivel with 2" Hex, HNW Side Inlet Coring Swivel with 1-5/8" Hex. Rig has approx. 4,933 Hours.
Rotary G - SRS #2741
DESCRIPTION: Gardner Denver; Model: 2000 Range III; Compressor: N/A; Mud Pump: GD FXX 172 Duplex; Engine: PTO; Mounted On: 2005 International 5600i 6X8; Truck Engine Make: Cummins ISX425; Tools/Options: Gardner Denver 2000 Range III: 2006 IR 1700 Mast, 59' Rated at 30,000# Static Hook Load Capacity. Mast is Complete with 3/4" Cable, Dual Raising Cylinders, 10" Crown Sheaves, Break-Out Wrench & Petol. Integral Hydraulic system Including Pumps, Common Reservoir, Thermal Exchanger & Infrastructure for Interconnecting Plumbing. Atlas Copco Model GD 2000 Topdrive Rated at 0- 5,000 ft Torque, 125 rpm, Fast Feed Down 200 fpm, Fast Feed Up 137 fpm. Braden Model CH230 Drawworks Rated at 18,000#, Strung with 3/4" Line. King Model CM25 Swivel. Duplex Mud Pump Rated at 52 HP, 330 RPM Maximum on Jackshaft. Pump is Hydraulically Driven and has an 8" Stroke X 6" Bore (4" NPT Suction Connection X 3" NPT Discharge Connection). C&H Fabricating Range III Pipe Handling Arm, 3,300# Load Capacity, 10,000 ft/lbs Maximum Torque Capacity. Truck is a Tandem Steer X Tri-Drive Truck. Eaton 18-Speed Manual Transmission. (2) 20,000# Front Axles, (3) 18,000# Rears. 11,292 Hours, 218,416 Miles.
Rotary G - SRS #2638
DESCRIPTION: 1997, Gefco; Model: Strata Star Drill 10 LS; Compressor: IR 400/200; Mud Pump: 7-1/2" X 10; Engine: Cummins 5.9; Mounted On: 1996/97 International 490 6X6; Truck Engine Make: DT 466; Tools/Options: Gefco Strata Star Drill 10 LS: 2,000# Winch, 24' Stroke, 20K Pullback, 10-Speed High Torque Tophead Rated at 12,800 ft lbs Torque, Rig is also Capable of Auger Drilling, Stand up Hydraulic Rod Rack, Transfer Case Rebuilt 3/14. Includes 240' 4" X 20' Rod & 360' NWJ Rod, Rod Trailer. 30,000# Winch on Truck. Working Daily.
Rotary G - SRS #2409
DESCRIPTION: 1973, Gardner Denver; Model: 15W; Compressor: WEJ; Mud Pump: None; Engine: PTO; Mounted On: Crane Carrier with Tandem Steering; Truck Engine Make: Detroit 8V92; Tools/Options: Gardner Denver 15W Year: Carrier is equipped with tandem steering, Extra Large Detachable Jack Pads. 4" X 25' Kelly, 3-Part Line, 8" Sliding Table, Hydraulically Driven Bean Injection Pump, Front & Rear Jacks, Rod Box. Also Includes a 700 Gallon Water Tank on Deck. Includes 300' of Drill Rod.
Rotary G - SRS #1641
DESCRIPTION: 1977, Gardner Denver; Model: 17W 1; Compressor: 750/250 2 stage Screw; Mud Pump: 5X6 GD Air Operated; Engine: PTO; Mounted On: 1977 CCC Hendrickson 3 axle; Truck Engine Make: Detroit 8V92T; Tires: Good Flotation on Front; Tools/Options: Gardner Denver 17W 1: 44' Derrick, water injection, winch. Table Retracts. Air Operated Mud Pump, No Leaks, Nice and Straight. New Cooler, 2nd Owner. Includes 300' of Drill Rod.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |