Rigs
Rotary R - SRS #4493
DESCRIPTION: 1996, Reichdrill; Model: T-650 W II; Compressor: 1150/350; Mud Pump: None; Engine: CAT 3406B; Mounted On: 1996 Ford LT-8000; Truck Engine Make: Cummins 300 HP; Condition: SOLD; Tools/Options: Reichdrill T-650 W II Year: 1996: SOLD Brand New Compressor with approx. 140 Hours on it. Newer Upper and Lower Chains. 38,000# Rated Pullback Capacity, HD 160# Chains, 26,000# Down Pressure, Standard 140# Chains, Chains are about 2 years old, Spare Chain Parts Included. 34' Mast, (2) 4.5" Hydraulic Mast Raising Cylinders, Hydraulic Retractable Table, Carousel Holds 7 Rods, Hydraulic Breakout Wrench, 4-cylinder Bean Water Injection Pump, (2) Rear 36" and (1) Front 48" Leveling Jacks. New Valves on Top of Jacks, New Water Injection Control Valve. 3,000 psi Capacity Water Injection Pump Valve, Hydraulic Winch, Jib Boom, Rod Rack Capable of Holding (12) 4.5" Rods, Night Lights. Deck Engine has a New Starter and Newer Injection Pump, New Tach Installed a few Years Ago. Serviced every 200 Hours including the Funk Oil and Air Filters. Carousel and Rod Box Included but not on the Rig. Rig is set up to run 4.5" x 20' X 2 7/8 IF" Drill Pipe, Hour Meter Reads approx. 8,170. Truck has a 9-Speed Fuller Transmission,18,000# Front Axle, 46,000# Rear Axle, Hendrickson Suspension. Truck Engine has approx. 73,066 Miles on it. Includes a New, Full Set of Front and Rear Tire Chains. Rig is Operational. Includes J-Wrench, 48" Tongs, 48" Breakout Wrench, Rod Bushing, 6" and 8" Slips. Welder in Photo Not Included. Atlas 2000 Casing Hammer Available at an Extra Cost. Rod Box and Carousel Included. SOLD
Rotary S - SRS #4625
DESCRIPTION: 2001, Schramm; Model: T300M; Compressor: See Below - Off-Board; Mud Pump: See Below; Mounted On: 2000 IHC 4900 6X6 AWD; Truck Engine Make: DT 530; Tools/Options: Schramm T300M Year: 2001: Rig was Fully Serviced when Recently Parked. Rig has an On-Board Mud Puppy System that has 3 Desanders, Homemade Tank and 3 Mud Puppy Shakers, 4X3 Centrifugal Mission Mud Pump on Board with New Fluid End 50 Hours Ago. Factory Warranty Engine with Low Hours (4-5 Seasons on it), Electric over Hudraulics, 2 Hydraulic Cylinders to be Replaced on the Carousel. Air Compressor has been Removed and needs gone through. Drill is set up to run 3.5" Schramm Drill Rod, 10-Rod Carousel set up for 20' Rods. Truck has Front Wheel Assist, Locks Side to Side. Includes: (10) 3.5" Drills Rods that are Worn, Spare Swivel O-Rings, some Spare Parts. Radio Controlled Geo Loop 50-500 Grouter Available for Extra Money.
Rotary G - SRS #4658
DESCRIPTION: Gardner Denver; Model: 1000; Compressor: GD ADL; Mud Pump: 5X6; Engine: PTO; Mounted On: 1996 Peterbilt 385; Truck Engine Make: CAT 3116 Rebuilt; Tires: Good; Condition: Ready to Drill; Tools/Options: Gardner Denver 1000: CAT Engine and Transmission has been Recently Rebuilt. 32' Mast, 23' Kelly, 7-1/2" Retractable Table, 4 Jacks. Includes 300' of 3" X 15' Drill Rod. Clutches Rebuilt, New Drawworks Brakes, New Cable, New Hydraulic Pump and Pulldown Motor. Linkage is Tight. Lots of New Parts. Recent Paint.
Rotary E-F - SRS #4593
DESCRIPTION: 2023, EPIROC; Model: DB40; Compressor: 1070/360; Engine: PTO; Mounted On: Peterbilt 367; Truck Engine Make: Cummins 605 HP; Tools/Options: EPIROC DB 40 Year: 2023: Rig is Set up to run 4.5" Drill Rod, Rod Spinner, 25 GPM Water Injection, Short Mast (approx. 35'), 18K Jib Boom.
Bucket Rig - SRS #4657
DESCRIPTION: Gus Pech; Model: G48; Engine: Ford 300 Industrial; Mounted On: 1979 Ford F800; Truck Engine Make: 477; Tires: Good; Condition: Good Running Condition; Tools/Options: Gus Pech G48: 3" 100' K-Bar. Extended Derrick, Rebuilt Clutches, Bearings and Shafts. Spare Pinion Gear for Turntable. Ready to Work.
Water Truck - SRS #4656
DESCRIPTION: 2010, Northwest Flat Tank; Model: 2,300 Gallon; Mounted On: 2000 Peterbilt 357; Truck Engine Make: Cummins 370 HP; Tires: Like New; Condition: Great; Tools/Options: Northwest Flat Tank 2300 Gallon Year 2010: 6-Point Flex Mount on Truck, 50' Torch Reel(never used), 25' of 3/4" Fuel Hose Reel and Auto Nozzle, 12V - 20 Gallon Transfer Pump - Like New Barely Used, 80 Gallon Fuel Tank, Work Lights, 20 Gallon PTO Hydraulic Reservoir, CW Sight Glass Mounted Behind Cab onto Truck Frame. IMT 3820 7,500# Stick Boom Crane (radio Remote Operation and Tether. (4) 2" Ball Valves at every Corner of Tank, (1) 3" Ball Vale at the Rear of the Tank. Truck has 237,372 Miles (purchased with 202,300 Miles in 2009 - was a California Truck) 20K Front, 46K Rears, Engine Brake, Cruise Control, Power Mirrors, Air Ride Seats, A/C (never used). No Rust, Single Frame. Never used in the Winter and Stored Inside. Chalmers Rubber Block Suspension all Replaced, New Front Cover Gasket 2025, New Hood Hinges, New Coolant Hoses and Clamps. Brakes were recently done. New Clutch and Rear Main Seal 3 Years Ago. Serviced on a Regular Basis. Meticulously Maintained by Owner. No dents, leaks, cracks or rust. Truck and Tank are Clean, Tight and in Great Condition. Pre-emission.
Rotary H-I - SRS #4655
DESCRIPTION: 1994, Ingersoll Rand; Model: TH55; Compressor: IR 600/250; Mud Pump: 7.5" X 10" Centerline; Engine: PTO; Mounted On: 1993 IHC 2674 Tandem Double Frame; Truck Engine Make: CAT 3176; Condition: Very Well Maintained; Tools/Options: Ingersoll Rand TH55 Year: 1994: Well Maintained, Owner Operated Rig. Drill is set up for 3.5" Drill Rod, 9-Rod Carousel, Pipe Tub, Oiler, Myers Inj Pump. Mud Pump was New in 2010, New Pistons, Liners, Rubber, Packing in 2025 (4 wells drilled since). All Four Tophead Motors have been replaced, Top Head Guide Rollers, Bushing in all Sheaves, Cables, Auxiliary 4-stage Pump all Replaced. Gresen Valve Bank Rebuilt. Numerous Hydraulic Hoses were replaced as Required. 2023 Table was Rebuilt and all New Mast Pins and Bushings were Replaced. Previous Owner Rebuilt Spicer 792 Transfer Case. Previous owner also did some Motor Work, Uses no Oil and is a very fuel Efficient Mud Rotary Drill. Previous owner also replaced the ECM. Oil Pan was dropped a few years ago and bearings and crankshaft all look good per CAT. New Front Steer Tires in 2024, New Aluminum Rims in 2026, New Water Pump, Thermostat Housing, Surge Tank and Heater Core. Radiator Removed and Repaired. Double Frame Truck, 44K Rears. Regular Rig Maintenance on Oils and Filters on all Components. Hour Meter Reads 3,908. CAT has a 13-Speed Transmission with Overdrive. Mileage unknown, Odometer Turns while Rig is Running. Drill was Purchased Rebuilt in 2008, Compressor was rebuilt at that time. Rig is used for Mud Drilling Only, 360' Wells, Air Compressor only used for Testing, 100% Mud Rotary Rig. Rig is Stored in a Heated Shop during Winter Months. Only Drilled 12-15 Wells Per Year. Swivel and Topdrive Feed Control Leaks some. 500' of 3.5" Drill Pipe with 2-3/8" IF Threads a 2017 Geo Loop 40-500 Grouter with 11.8 Hours, stored inside (purchased new) and a Downhole Camera Purchased in 2010 also available for extra money. Drill Pipe Pins have been recut.
Water Truck - SRS #4654
DESCRIPTION: Steel; Model: 2,000 Gallon; Mounted On: 1999 Sterling; Truck Engine Make: Detroit 60 Series 430 HP; Tires: < 1 Year Old; Tools/Options: Steel Tank has no Leaks. Grouter Platform on Rear. Truck has a 10-Speed Transmission, approx.. 600,000 Miles. Brakes have been replaced.
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350 with Clutch; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Mercedes Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005: Rig has 4 Jacks. Includes approx. 400' of 4.5" O.D. Drill Rod, (5) Joints are older 25'ers and the rest are 20'ers in better condition, a 6" and 8" Hammer & Bits, tools, Hydraulic Wrench, Casing Driver and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles. Total Rig Hours are approx. 10,000. Compressor has a clutch and has less hours but hours are unknown. Recently Installed a New Compressor Cooler (zero hours), New Shaft & Bearings in Rotary Head, Four Rebuilt Hydraulic Pumps and one new Pump.
Rotary H-I - SRS #4653
DESCRIPTION: 1999, Ingersoll Rand; Model: T3W; Compressor: NEW 900/350; Engine: CAT 3406 REMAN; Mounted On: 1999 IHC 2500; Truck Engine Make: CAT C10; Condition: Reconditioned; Tools/Options: Ingersoll Rand T3W Year 1999: Lots of New and Rebuilt Components, Rig has been Reconditioned. Deck Engine has been Remanufactured and Certified, Brand New Compressor, 32' Mast, Rig is Set up to run 4.5" Drill Rod. New Cables, Hydraulics have either been Repaired or Replaced, Rebuilt Tophead, Rebuilt King Swivel and Rebuilt Water Pump. Table has been gone through and is Tight. Derrick Cylinder has also been Rebuilt, New Jacks. Truck has a Jake Brake. Rig has been Torn Down, Gone Through, Painted.
Rotary E-F - SRS #4498
DESCRIPTION: 2003, Foremost ; Model: DR12; Compressor: 950/350; Engine: PTO; Mounted On: 2003 Sterling 6X4 L9500; Truck Engine Make: CAT C15; Tires: Newer; Condition: FOREMOST - PRICE REDUCED; Tools/Options: Foremost DR7/25P-40/12-950 Year: 2003: New Cushman Box and Old Box has Been Rebuilt and on hand. Drill has 7,607 Hours, Truck has 20,863 Hours. Has a Rod Box, not on drill. Includes 10 Drive Shoes (8, 10, 12), New Diverters (6",8",10",12"), Jaws ( 6", 8", 10" and 12"). And a Couple Hundred Feet of 10' Drill Rod, 20' Drill Rod Available for an Extra Cost. A 1994 Ford Truck with a flat tank Water Body and Crane with 90,094 Miles also available for extra money. Also Available for Extra Money a 1997 Volvo Service Truck with 230,419 Miles. Also available for an extra cost is a 1979 Driltech D40K mounted on a 2005 Kenworth with 21,804 Miles, 2007 Chevy Silverado K2500HD Crew Truck with 210,000 Miles, 2013 Chevy Silverado K2500HD Crew Truck with 113,258 Miles. Oil and Filter changes are all documented. A New Sandline has been Installed on the DR12 along with a New Dashboard. All M&R Records are on File. TOTAL TURNKEY PACKAGE ALSO AVAILABLE AND INCLUDES: 2004 Flatbed Trailer (pipe hauler), Forklift, 100' of 10" Pipe, 2,280' of 5" Pipe, 12,760' of 6" Pipe, 380' of 8" Pipe, z92) Bunks & 320' of 4" Plastic, 6" DK Drive Shoes, 6" DR Drive Shoes, 8" DR Drive Shoes, 10" DR Drive Shoes, 12" DR Drive Shoes, 3,380' of 4.5" Drill Rod, 2 Pallets Bentonite Med, 2 Pallets #8 Bentonite, name, customer list, phone, goodwill, non-compete.
Rotary D - SRS #4496
DESCRIPTION: 1979, Driltech; Model: D40K; Compressor: 750/300 (rebuilt in 2024); Engine: CAT 3406; Mounted On: 2005 Kenworth; Truck Engine Make: CAT C15 475 HP; Condition: Tooled up, Working Drill - PRICE SLASHED; Tools/Options: Driltech D40K Year: 1979: Rebuilt in 2016, Owner believes the Compressor was Rebuilt in 2024. No Carousel, 40K Pullback 26,500 Pulldown, set up to run an Atlas 2000 Casing Hammer which is Included, runs 4.5" O.D. X 20' Drill Rod. Truck has approx. 21,800 Miles and an 18-Speed Road Ranger Eaton Transmission. Also Available: Tooled up 1997 Volvo Service Truck with approx. 231K Miles, approx. 200' of Used Drill Rod and (4) New Drive Shoes. Maintenance Records Available upon Request. Entire Business can be Purchased also, no Land or Buildings Included
Rotary S - SRS #4584
DESCRIPTION: 1989, Schramm; Model: T-660H; Compressor: 900/350 GHH; Mounted On: 2009 Mack Granite 6X4; Truck Engine Make: 485 HP; Condition: Good PRICE REDUCED; Tools/Options: Schramm T-660H Year 1989: Rig is Capable of Holding 280' of 4.5" Drill Rod Standing up between the Lazy Susan and Rod Rack on the Side of the Mast. Rig has an 18" Table Opening. 40K Pullback, 30' of Travel as well as a Foremost Floating Sub. New Upgraded Piggyback Pump & Rotation Pump (2021), Deck Engine Completely Rebuilt in 2019, Upgraded Hydraulic Pumps, New Preheat Deck Engine Heater in 2022, Added Helpers Side Controls for Winch and Jib Boom. Compressor also Rebuilt around the same time as the deck engine (2019), best guess on hours is approx. 3,000 (working drill). Most Recently 2025-26 the Deck Engine had New Injectors Installed, Built a New Wiring Harness on Rig, Rebuilt Head & Installed a New Shaft through the Head, Upgraded the Air Seals to a King Swivel. Truck has an 18-Speed Transmission and approx. 46,345 Miles, Routine Maintenance done Yearly, New Injectors in 22/23. Previous Owner Purchased the Truck New. Includes approx. 600' - 700' of Drill Rod.
Cable - SRS #4652
DESCRIPTION: Bucyrus Erie; Model: 22W Series II; Engine: 4-Cylinder Deutz; Mounted On: 1996 IHC Single Axle; Truck Engine Make: DT 466; Condition: Good; Tools/Options: Bucyrus Eric 22W Series II Year: New Hydraulic Jacks, Jackshaft Replaced, Bull Gear in Good Condition. All New Hydraulics, Hoses and Reservoir for Cylinder (derrick was converted to Hydraulic), Catwalk. Air Cooled Turbo Diesel Deck Engine Approx. 1,150' of 3/4" Kine and approx. 1,200' of 3/8" Sand Line, New 5/8" Non-rotating Casing Line New Hydraulically Driven Clutch Installed a few Years Ago, New PTO Coutch, New Drive Belt and Brand New Clutches on Jackshaft. Newer Shock Assembly, New Friction Wear Pads, New Bull Ring Flange Bushing. Built a New Tensioner Bracket, Spring and Rubber Cushion. 3 Hydraulic Jacks. 5-Speed Transmission, Newer Steer Tires. Having a brake issue that will be repaired. Includes some Tooling: 2-1/4 X 3-1/4 Pin Joint, 20' Stem, 6" Bit, Rope Socket, Maybe a set of Jars.
Rotary S - SRS #4651
DESCRIPTION: 2003, Schramm; Model: T450WS; Compressor: NEW 900/350 with clutch < 100 Hours; Engine: CAT 3406; Mounted On: 2003 IHC 7400 6X4; Truck Engine Make: CL300; Condition: Good, Well Maintained Working Daily; Tools/Options: Schramm T450WS Year: 2003: 25' Mast Travel, Slow Feed Drill-Up Valve, Single Motor Tophead, Dual Rotation Torque Limiters, 4.5" Split Table Assembly with Hood, 60" Breakout Wrench, Diesel Fired Coolant Heater, Oiler, Single Front Outrigger, Swing & Extend Jib, Floating Sub, 6" Hammer Holder, 8-Rod Lazy Susan set up for 4.5" Drill Rod, Sliding Hydraulic Tophead, Stabilizer Support Bars, Pipe Handling Controls, Auxiliary Winch Controls, 5,800# Winch (125' X 7/16"), Foam Injection, 18 GPM Bean Water Injection Pump, Angled Pipe Rack, Air Line Filter, Full Side Walkways, Junk Box.. Rig is set up to run 4.5" OD X 20' Drill Rod with 2-7/8 IF Threads. Deck Engine shows 13,483 Hours, Maint Records Available (250 hr. and 1,000 hr. oil changes since purchased new) Chassis Engine has 31,593 Miles on it. NEW Sullair Compressor Installed in 2026, has < 100 Hours. Approx. 400' of rod and a new 6" bit included.
Pump Hoist - SRS #4650
DESCRIPTION: Jessen; Model: Monitor 33; Mounted On: 1996 Chevy 3500 2WD; Truck Engine Make: 6.5L Turbo Diesel; Tires: 4 New Rear; Condition: Great, Runs Good; Tools/Options: Jessen Monitor 33 Year: This Unit is the bigger Jessen with the round tube pipe. Truck has a 5-Speed Manual Transmission and odometer Reads 231,417 Miles but Newer Engine, Clutch and Pressure Plate was installed about 20 Jobs ago (approx. 10-15K miles ago). New Batteries and 4 New Rear Tires were also Installed. Unit has been used as a spare hoist. Same owner for many years. Good Working Table and Vise. One line machine, set up for a remote but never had one.
Rotary E-F - SRS #4649
DESCRIPTION: Failing; Model: CF-15; Mud Pump: 5-1/2" X 8" Gardner Denver; Mounted On: 2005 Kenworth; Truck Engine Make: CAT C7; Condition: Good Working Condition; Tools/Options: Failing CF-15: 5-5/8" Retractable Table, 23' Kelly, Pulldown, Air Clutches. Includes approx. 260' of 2-7/8" Drill Rod on Truck. Truck has approx. 200K Miles, Odometer Turns when Drilling. Truck has been serviced and engine runs strong.
Miscellaneous - SRS #4648
DESCRIPTION: Kyle; Model: +/- 3,500 psi Frac Unit; Engine: PTO; Mounted On: 2007 GMC 5500; Truck Engine Make: CAT Diesel - Remanufactured; Condition: Good; Tools/Options: Kyle Frac: Complete Frac Unit approx. 3,500 psi. Unit was used for Frac Work Only, no Oilfield Work. Kyle 8,000# Full Rotating Crane. Comes with Aluminum Pipe and Packer. Has been stored inside. < 100K Miles on Truck. Unit has been Recently Painted. Remanufactured CAT Engine.
Rotary R - SRS #4587
DESCRIPTION: Late 2005, Reichdrill; Model: T-690 W; Compressor: Sullair 1070/350; Engine: CAT C15; Mounted On: Mack Granite; Truck Engine Make: Mack; Condition: SOLD; Tools/Options: Reichdrill T-690 W: Late 2005 Year Model, One Owner Drill, Approx. 5,400 Hours on Deck Engine. 40K Pullback, New Style Carousel, Regen, One Winch, Catwalk, Two Rear and One Front Jack, Rod Box can hold 19 Joints of 4" or 15 Joints of 4.5", 9-Pod Carousel Set Up for a Rods & a Stabilizer, Air Operated Holding Wrench, Water Injection, Oiler, Mast has a 28' Stroke, 20" Table Opening, Torque Limit Control. Includes 300' of 4.5" Drill Rod with 3.5" API Threads, (1) Used 6" Hammer. Truck has a Jake Brake and approx. 59,000 Miles on it. SOLD
Rotary S - SRS #4647
DESCRIPTION: Schramm; Model: T450H; Compressor: 750/300 GHH; Engine: PTO; Mounted On: 1990 Ford; Truck Engine Make: 6V92; Condition: Very Good for Age; Tools/Options: Schramm T450H: 7-Pod Carousel, Water Injection, Hydraulic Breakout Wrench, No Sandline, Helper and Driller Platforms, Front and Rear Jacks, Rod Box, Tool Boxes. Drill is set up to run 4.5" Drill Rod. Engine has been Rebuilt. Low Hours on Compressor. New Engine Radiator, New Pump Drive Coupling, New Mast Lift Cylinder.
Rotary H-I - SRS #4646
DESCRIPTION: 1998, Ingersoll Rand; Model: T4W; Compressor: 900/350; Engine: CAT 3406; Mounted On: CCC; Truck Engine Make: CAT 3306; Tools/Options: Ingersoll Rand T4W Year 1998: 50K Pullback, 1,000' of 25' Drill Rod. 7-Pod and 4-Pod Carousels are included but not mounted. Bean Injection Pump.
Rotary C - SRS #4645
DESCRIPTION: 1978?, Chicago Pneumatic; Model: RT 2000; Mud Pump: Centrifugal; Engine: PTO; Mounted On: IHC; Truck Engine Make: DT 466; Tools/Options: Chicago Pneumatic RT 2000: 10" Retractable Table, Air Clutches, Drawworks Run off of a Hydraulic Motor, Sandline, Double Drum Drawworks, Double Brakes, Hydraulic Pulldown, 33' Square Kelly, 3" Swivel. Recently drilled a few wells. Capable of Lifting 43' Pipe and clear the rotary table. Mast Cylinders and Leveling Jacks have been reworked, Rebuilt Valve Bank. Truck Engine Runs Good, not a lot of power going down the highway. Also has 1,500' of 3.4" Regular, 4.5" Flush Joint Pipe with its own trailer and a slide for extra money. Some Drill Collars are also available. Currently drilling 400' - 500' wells but mast would need repaired to drill to it's 2,000' capability. Bottom 20' of the derrick needs to be repaired, rusted.
Bucket Rig - SRS #4644
DESCRIPTION: 1978, Gus Pech; Model: Super George 66; Engine: Cummins 6.7L (952) Hours; Mounted On: 2006 Sterling; Truck Engine Year: Mercedes 12.8L; Truck Engine Make: Diesel; Tires: Good; Condition: Good; Tools/Options: Gus Pech 66 Super George: Year 1978: New Deck Engine installed in 2017 has approx. 952 Hours on it. 51" Table with Brand New Ring and Dowmax Hydraulic Drive Motor in 2026, 14 - 17,000# Main Winch, Sandline. 94' Drive Kelly Rebuilt in 2020., 12 Ton Auxiliary Winch. Includes one each - 18", 32" and 42" Buckets, 8" Reverse Swivel with 20' 8" Kelly, 34 Joints of 8" X 25' Flanged Drill Pipe with External Air, 28" and 48" Reverse Drill Bits. Truck has approx. 244,035 Miles and a 10-Speed Fuller Transmission.
Rotary A-B - SRS #4643
DESCRIPTION: Atlas Copco Ingersoll Rand; Tools/Options: Atlas Copco: 70K Jib and 30K Hoist. Was removed from a 2021 Atlas Copco TH-60.
Auger - SRS #4642
DESCRIPTION: 1978/79, Mobile; Model: B53; Engine: Detroit Diesel; Mounted On: 1995 Ford F800; Truck Engine Make: Diesel; Tools/Options: Mobile B-53 Year: Drill is a 1978/79 Year Model. Manual 140# Hammer, Two Winches (main & auxiliary), Wireline Winch, Shelby Tube Extruder, Hydraulic Chuck. Includes tooling: auger, bits, AW rod, auger forks, adapters, shelby tube heads to name some of the tooling included. Water pump is not in working order.
Rotary E-F - SRS #4641
DESCRIPTION: 2002 or 2003, Foremost; Model: DR24; Compressor: 900/350 Atlas Copco; Engine: PTO; Mounted On: Sterling; Truck Engine Make: CAT C15; Condition: Working; Tools/Options: Foremost DR-24 Standard Year: 2002. Drill is a 2002 or 2003 Year Model. Engine Shows 16,666 Hours on Truck but CAT Engine was Replaced at 10K Hours. 637K Current Miles. Has 3" Airlines. 10" & 16" Diverters, Set of 6", 10" and 16" Jaws, Discharge Swivel (16"?), All work has been done within the last 2-5 years. New Topdrive (part where it slides - case motors, tilt cylinder all replaced), Main Lift Cylinder Replaced, Lower Drive Lift Cylinder Rebuilt, New Lower Drive Chain and New Lower Drive Bearing, Tri drive Box Rebuilt and next Gearbox Back has been stamped & gone through, leaks a little. New Power Steering Pump and Gearbox, New Brake Shoes. It has the upgraded Holdback System (electronic holdback switch to holdback or can bypass). No Rod Available.
Rotary G - SRS #4640
DESCRIPTION: 2015, GEFCO; Model: 30K; Engine: PTO; Mounted On: Peterbilt; Condition: Working Daily; Tools/Options: GEFCO 30K Year: 2015. New Tophead Motor, Seals and Wear Sleeves. New Swivel Seals, Newer Floating Sub Saver also Installed. New Pulldown Cylinder Rod and Rebuilt Cylinder Rod and Rebuilt Cylinder, New Tophead Motor within the last 8 Months. Spare Breakout Cylinder, Spare Air Control Valves and a lot of additional spare parts, air control valve regulators etc. Includes 1,000' of 4.5" X 20' Drill Rod. Currently has approx. 1,200 Original Hours on Air Compressor and approx. 8,800 Frame Hours & 101,000 Miles. Rig has been Maintained and Serviced Meticulously.
Rotary S - SRS #4014
DESCRIPTION: Speedstar; Model: SS-22; Mud Pump: GD FXO 7-1/4" X 10"; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: N 14 460 HP Cummins; Tires: Near New; Condition: Good; Tools/Options: Speedstar SS-22: Capable of Range III Casing up to 44'. 10" GD Retractable Rotary Table, Rotary Transmission with 5 Forward & 1 Reverse, Bean 4-Cylinder Injection Pump, Custom Built 56' Heavy Duty 3" Square Tubing Mast with Huge Hydraulically Folding Racking Board & Heavy Duty Substructure. Drill is Set Up to Run 30' Drill Pipe, 36' X 6" Hex Kelly with Retract, 3" Little Giant Swivel Rebuilt, PTO Rebuilt. Front & Rear Air Actuators on Driller's Panel, Main Clutch Control below Driller's Panel, Completely Rebuilt SS-22 Double Drum Brake Drawworks with LeBus Grooving, 18" Air Clutches & 3rd Sandline Drum, Hydromatic Brake, 2 Huge Traveling Blocks, Newer Hydraulic Pump, (4) Hydraulic Jacks & (2) Screw Jacks under Rotary Table Frame, Planetary Pulldown, Hydraulic Spinning Chain, Folding Drill Floor, Newer LED Lights throughout Rig. Swivel REcently Machined to sit Tight in the Cradle and had the Kelly Pin Recut. Carrier has a Fuller Road Ranger Transmission. Engine has a new PCM & Injector Pump, Rear Air over Electronic 2-Point Throttle Control, All 12 Tires are Newer, Driven approx. < 500 Miles. Includes approx. 2,100' of 3.5" X 30' Drill Pipe with 3.5" IF Tool Joints & (6) Drill Collars, Slips, Screw Plug & Bit Subs. Un-used Weight Indicator with 2 Load Cells Available for an Extra Cost (not mounted on rig). Almost Everything has been Rebuilt on this Rig from Early to Mid 2000's to Present. Heavy Duty Rig with a Big Mud Pump and Small Footprint.
Sold - SRS #4639
DESCRIPTION: 2023, Drillmax ; Model: DM250; Mud Pump: 4X3X13 MCM Centrifugal; Engine: PTO; Mounted On: Ford F600 4WD; Truck Engine Make: 6.7L Powerstroke; Condition: SOLD; Tools/Options: Drillmax DM250 Year: 2023: Tophead Rated at 12,000# Pullback, 5,500# Winch with Spare Cable and Hook. Two Spring Loaded Lift Plugs, One 4" Suction Hose with Check Valve and Strainer. 5' Extra Drill Rod (short piece). Full Spare Pump on Pallet $x3X13 MCM. Includes 600' of 3" X 20' O.D. Drill Pipe with Mayhew Regular Tool Joints. Various Bits, Mostly 7" Drag Bits. Has approx. 2,400 Hours on it and Truck has approx. 6,000 Miles. SOLD
Rotary H-I - SRS #4602
DESCRIPTION: 2000, Ingersoll Rand; Model: T4 Deephole Package; Compressor: 1070/350; Engine: Cummins QSK19; Mounted On: CCC; Truck Engine Make: Cummins L10; Condition: Well Maintained SOLD; Tools/Options: Ingersoll Rand T4W DH Package Year: 2000: 70K Deephole Package, Jib Hoist, Spur Gear Tophead and Compressor have been Rebuilt. Deck Engine was Reconditioned by Cummins in Oct. 2006 @ approx. 6,152K Hours. Compressor Rebuilt in Dec. 2013 @ 10,773 Hours (rebuilt & Installed by Atlas Copco), at the same time both Tower Rams were Rebuilt. Spur Gear Tophead Reconditioned, Rebuilt & Installed in March 2015 @ 11,825 Hours. May 2016 Rebuilt Dennison Main Pump & Charge Pump, Packed all Main Bearings in Tri-Box @ 17,864 Hours. July 2022 all New Sprockets in Tower and New Chains (top, middle & bottom) at 18,239 Hours. As of Aug., 2026 Drill has 19,114 Total Rig Hours. Rig was added to the Fleet in 2003 at around 2,100 Hours total. Pipe Available for an Extra Cost: approx. 2,100' (84 joints) of 4.5" X 25', 1,200' (48 joints) of 4-3/8" or bigger X 25', 900' (36 joints) of 4-1/4" - 4-3/8" X 25'. Oil Samples done every Oil Change.. Condition: Well Maintained. SOLD
Sold - SRS #4406
DESCRIPTION: 2021, Atlas Copco EPIROC; Model: TH-60 Deephole; Compressor: 1070/350; Mud Pump: See Below; Engine: PTO; Mounted On: 2021 Peterbilt 367; Truck Engine Make: Cummins X15 600 HP; Condition: SOLD; Tools/Options: Atlas Copco TH-60 DH Year: 2021: SOLD. 36' Mast with 70K Pullback. Mud Piping with Auxiliary Hydraulic Pump to Run Offboard Mud Pump. 25 GPM Bean Pump (w/o Foam Injection), 7-Rod Carousel, 18,000# Lifting Capacity Main Hoist, Sandline Hoist, Single Rod Loader, Rod Spinner, Steel Platforms, Torque Limit Control, Dual Jib Controls, Dual Hoist Controls, 7 Gallon Electric Oiler, 3" Air Piping. Set Up to Run 4.5" X 20' Drill Rod with 2-7/8" IF Threads. 26' of Head Travel from Spindle Shoulder to the Table. 500' of 4.5" Drill Rod Available. Drill is Capable of Carrying 500' of Rod. Truck has an 18-Speed Fuller Transmission, approx. 18,117 Miles, approx. 3,236 Engine Hours and approx.. 1,784 Compressor Hours. Recently (2025) changed all the Hendrickson suspension, did a complete service and replaced the belts. Truck has 22,000# Front Axle and 46,000# Rears. SOLD
Rotary G - SRS #4393
DESCRIPTION: 2018/19, GEFCO; Model: 40K; Compressor: Sullair 1000/350; Mud Pump: Plumbed; Engine: PTO; Mounted On: 2019 Peterbilt 367 6X4; Truck Engine Make: Cummins 565 HP (recently rebuilt); Condition: Working Drill PRICE REDUCED; Tools/Options: GEFCO 40K Year: 2019: Newly Rebuilt Engine (Injectors, Turbo, Oil Cooler), Truck Brake Compressor also Rebuilt. Rig is set up to Run 4.5" X 20' Flush Joint Drill Pipe with 2-7/8" IF Tool Joints and a Holte 350 Casing Hammer. 25K Pulldown, 40K Pullback. 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator, 25,000# Single Line Hydraulic Main Winch over the Jib. Hydraulic Rod Spinner, Modified 60" Breakout Wrench, Auxiliary Winch Mount & Hydraulics (rig has 2 winches, cable recently replaced), 3-Speed Tophead, 15 Piece Rod Box, 6-Rod Carousel, Hammer Holder. Upgraded Joysticks (5-Volt Electric Upgrade), Compressor has approx. 2,300 Hours, approx. 6,000 Total Frame Hours, < 500 Hours on the Newly Rebuilt Engine.. Truck has 22,000# Front Axle, 46,000# Rears, 18-Speed Fuller Transmission. 400' of used pipe included.
Truck - SRS #4636
DESCRIPTION: Mounted On: 2019 Peterbilt; Truck Engine Make: 605 HP Cummins; Condition: Near New; Tools/Options: 2019 Peterbilt - EPIROC PTO Rig Ready Truck Chassis. Set up for a TH-60 or DB40 Drilling Rig. Was used just as a Stock Demo Truck. Only has 436 Miles and 537 Total Hours. 18-Speed Fuller Transmission, Namco PTO Box, 68,000# GVW, Double Frame Rail, Dual Rear Differential Lock, Power Windows, A/C, Hands Free, Heated Mirrors, Chrome Package. This type truck can Typically only be ordered by Manufacturer.
Rotary R - SRS #4635
DESCRIPTION: 1985, Reichdrill; Model: T-650; Compressor: 900/350 GHH; Engine: CAT 3406 - Rebuilt; Mounted On: 1985 IHC S2600; Truck Engine Make: Cummins 300 HP; Tires: 95%; Condition: Good; Tools/Options: Reichdrill T-650 Year: 1985: Rebuilt CAT Deck Engine Installed in 2026 (approx. 2,500 hours since rebuild). Twin 4.5" Pulldown Cylinders, Chains are in very good to excellent condition. Dynex Head Motor, 4 Hole Fund Gearbox, Webasto Engine Preheater, Helper Controls Installed and Foldup Catwalks. Truck has a 7-speed Transmission. Odometer Reads approx. 104,800 Miles and works. Includes 400' of Used 20' X 4.5" X 3.5" Reg pin up by box down included. Also Includes all Hand Tools. Hour Meter Reads 12,380. Recent (2026) Inspection included brake replacements and 4 new tires.
Sold - SRS #4634
DESCRIPTION: 2024, Drillmax; Model: DM250; Compressor: 125 CFM; Mud Pump: 4X3X13 Centrifugal; Engine: PTO; Mounted On: 2024 Ford F600 4WD XL; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Drillmax DM250: SOLD Bed Cover Kit, Folding Step Weldment, Breakout Wrench Assembly, Mast Assembly, Mast Lights. DMR3 High Torque Head, Breakout Fork Weldment, Two Subs (2.375 IF pin X 2.375 Mayhew Reg. Box & 2.375 Mayhew Reg. Pin X Pin 16") 3" Centralizer, 8-Rod Carousel, No Helper Controls, 5,000# Winch, Aux. Pump Delete, 20' Rod Box (holds 5 rods), Casing Slip Kit, 36" Underbody Toolbox, Odometer Reads 16,188 Hours, 2,228 Rig Hours and Air Compressor has 845 Hours. SOLD
Rotary M - SRS #4633
DESCRIPTION: 1979, Mayhew; Model: 1400; Mud Pump: See Below; Engine: PTO; Mounted On: 2012 Peterbilt 348; Truck Engine Make: Diesel; Condition: Working Drill; Tools/Options: Mayhew 1400 Year: 1979: Refurbished. Equipped with Two Mud Pumps - 5X6 Duplex 1FXG172 and a 7-1/2" X 8" Duplex. Four Leveling Jacks, 7-1/2" Non Retractable DSM Rotary Table. Air Clutches on Pump but not on Drawworks, New Derrick in 2009, New Truck in 2012, New Mud Pump and Power Take-off in 2012. Truck Odometer Reads 17,745. Includes 700' of 4" O.D. Drill Pipe.
Sold - SRS #4465
DESCRIPTION: 1978, Simco; Model: 5000 WS; Mud Pump: Mission 4X3 Centrifugal; Engine: Ford 300; Mounted On: 1991 GMC Topkick - Single Axle Truck; Truck Engine Make: CAT 3208; Condition: SOLD; Tools/Options: Simco 5000 WS Year: 1978: SOLD Single Axle, Automatic Transmission Truck, Pipe Rack, Driller & Helper Platforms, Toolboxes, Two Rear and One Front Jack. Mud Pump Rebuilt approx. 15 Wells Ago. No Sandline, Gearmatic Model 25 Winch, 13,600# Maximum Line Pull, Hydraulic Breakout Wrench, 10" Hinged Table, Swing out Tophead to Set Casing. Includes 150' of 4.5" X 15' Aluminum Flush Rod on the Truck, Multiple Bits. More Rod Available. Truck has approx. 106,373 Miles on it. SOLD
Water Truck - SRS #4619
DESCRIPTION: Flatwater Fleet; Model: 2000 Gallon; Mounted On: 2004 IHC; Truck Engine Make: Cummins ISM 370 HP; Tools/Options: Flatwater Fleet 2,000 Gallon: Truck has approx. 291,000 Miles, Eaton 8LL Transmission. Twin 100 Gallon Fuel Tanks up front behind the cab. 20' of Usable Bed Space, entire length from behind the cab is approx. 22'. 6,000# Crane with Wireless Remote. July 2026 - New Turbo, EGR, Valve Body. Swapped out a Weak Injector and Head on the Motor. Front and Rear Ends were just Rebushed 2 Years Ago. Second Owner.
Sold - SRS #4512
DESCRIPTION: 2016, Hunke; Model: 6T; Engine: PTO; Mounted On: 2016 Ram 5500 4WD; Truck Engine Make: Cummins 6.7L; Condition: SOLD; Tools/Options: Hunke 6T Year: One Owner, Sandline with approx. 1,000' of Cable, 3 Outriggers, Hunke Tilting Pipe Racks. Owner believes there is a wired remote. Truck is Equipped with Power Windows, AC and has approx.. 98K Miles. 11' Palfinger Bed, Spray in Bedline. There is Moderate Damage to Driver Side Front Corner, Swiped 6 Years Ago. The Door was modified to close securely and was used daily in it's current state. SOLD
Sold - SRS #4161
DESCRIPTION: 2003, Versa-Drill; Model: V-2000; Compressor: 1070/350; Mud Pump: Has hydraulics for one; Engine: PTO; Mounted On: Kimble 4WD; Truck Engine Make: CAT C16; Condition: SOLD; Tools/Options: Versa Drill V-2000 Year: 2003: SOLD 80K Pullback, Tophead has all New Bearings and Seals. Rod Handling System that can carry 500' of Drill Pipe. It has Power Beyond for 3X4 Mud Pump. New Starter and New Clutch Installed February 2023. Newer Tires on the Front & Rear, New Tophead Drive Motors Installed in 2023. Rebuilt Rotary, Main Winch, 4 Rear Pumps (included but not installed), Walking Beam Suspension. Front End Gone Through, Some Hoses Replaced, New Fluids. SOLD
Rotary E-F - SRS #4617
DESCRIPTION: 2009, Foremost; Model: DR 24 Standard; Compressor: 900/350; Engine: PTO; Mounted On: 2009 T800; Truck Engine Make: 600 HP; Condition: Working Drill, Low Hours; Tools/Options: Foremost DR 24 Standard Year: 2009: Approx. 3,000 Compressor Hours, Approx. 5,500 Total Hours and 22,000 Miles. Includes 4 sets of Jaws, One 10" Discharge Swivel. Drill has the Newer Style Controls, Fast Feed. New Plumbing and some hoses. New Transfer Case Box.
Rotary H-I - SRS #4420
DESCRIPTION: 1978, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Mud Pump: 5X6; Engine: PTO; Mounted On: 1979 IHC Paystar 5000; Truck Engine Make: Detroit 8V92 < 10 Hrs.; Condition: Working Drill PRICE REDUCED! New Cab - Rebuilt Engine, Low Hours; Tools/Options: Ingersoll Rand TH-60 Year: 1978 PTO; Compressor: 750/250; Mud Pump: 5X6; Mounted On: 1979 IH Paystar 5000; TrEngine: , Detroit 8V92; Tools/Other Options: 3rd Owner, 13-Speed Transmission, 2-Cylinder Injection Pump, Main Winch, Sandline Winch. New Batteries, Rebuilt Starter. Includes 300' of 3.5" OD Drill Rod with 2-3/8" Threads. Bearings in Transfer Case were Replaced in 2023 Budd Style Wheels on the rear. Jack Cylinders need Repacked, Compressor needs an Oil Seal Replaced on the Front where the Clutch Mounts. There are some other small hydraulic leaks. Cab has just been replaced along with a Rebuilt Engine Installed (2026) with < 10 Hours on it. New Clutch, New Water Swivel Packing. Includes some spare parts (truck air compressor, power steering pump, alternator and radiator). Previous showed it having 32,500# deep hole package, 34' mast, 9-rod carousel and parts manual - to be confirmed that has not changed.
Rotary G - SRS #4433
DESCRIPTION: 2016, GEFCO; Model: SS-22 RC HD; Compressor: DR 500/200; Mud Pump: 6X5X14 National; Engine: PTO; Mounted On: 2015 Peterbilt 367; Truck Engine Make: Cummins ISX15 525 HP; Condition: SOLD; Tools/Options: GEFCO SS-22 RC HD Year: 2016: SOLD Telescoping Jacks, Original Build Sheet Shows 18" Failing 150 Ton Rotary Table, 6" Western Rubber Swivel, 6" Western Rubber Air Side Inlet, 23' Kelly Bar, 7" Dual Outside Air Flange Ends, 4-Part Kelly Line with14" Block, 4-Part Pipe Line with 14" Block, Sandline, 15' Mast Extension, 6" Swivel. Truck Odometer Reads 14,854 Miles and 5,206 Hours. Compressor needs a new air end, Problem with Small Auxiliary Winch. Some Flange Connection Outside Air Drill Pipe Available for an Extra Cost. Not confirmed but seller was told it has 90K pullback when the block is at the table and 70K pullback when it's at the top of the mast.
Sold - SRS #4566
DESCRIPTION: Mud Puppy; Model: 170-2SC; Mud Pump: 7-1/2" X 10" Duplex; Engine: CAT 75 HP Tier 4; Mounted On: Custom Trailer; Condition: SOLD; Tools/Options: Mud Puppy MP 170-2SC with a 7.5" X 10" Duplex: Mud Puppy is approx. 4 Years Old, Custom Trailer. The mud pump is powered by the drill rig hydraulics. The mud pump would need to be powered by another Drill rig or power supply. An engine would fit on the trailer or have a drill rig plumbed with hydraulics to handle it. SOLD
Rotary S - SRS #4441
DESCRIPTION: 1977, Speedstar; Model: SS-15; Compressor: LeRoi 600/250; Engine: PTO; Mounted On: CCC; Condition: Working Drill; Tools/Options: Speedstar SS-15 Year: 1977: Tophead Drive, 43' Mast, Manual Clutches. One Front Jack and Two Rear Jacks, Driller/Helper Platforms. Includes 300' of 4.5" X 20' Drill Rod with 3.5" Regular Threads, a Refreshed Compressor and a Rod Box. Tiger Tierra Casing Hammer Available for an Extra Cost. Approx. 400,000 Miles on Truck. No Hour Meter. Compressor Maintenance was done approx. 6 Months ago (april, 2026). Engine was upgraded to the 400 Cummins from a 350 Cummins. Licensed and recently inspected (Sept 2026)
Sold - SRS #3372
DESCRIPTION: 1974, Ingersoll Rand; Model: T4; Compressor: 600-150/250 Rotary Vein Rebuilt 2011/12; Mud Pump: None; Engine: PTO; Mounted On: CCC; Truck Engine Make: Detroit 318; Condition: SOLD; Tools/Options: Ingersoll Rand T4 (1974): Truck was on fire but rig runs per owner. Rotary Vein Compressor, that was rebuilt 2011/12. Present Owner Owned it since 1980, Only Drilled 8 Wells. Table plate comes out allowing for about a 22" opening. Includes approx. 150' of 5.5" O.D. X 25' Drill Rod. SOLD
Sold - SRS #4631
DESCRIPTION: Smeal; Model: 5T; Mounted On: Unmounted; Condition: SOLD; Tools/Options: Smeal 5THSRPPG: Sandline. SOLD
Pump Hoist - SRS #4630
DESCRIPTION: Hunke; Model: 6T; Mounted On: 2022 Ford F550 4WD; Truck Engine Make: 7.3 L Gas; Condition: Great; Tools/Options: Hunke 6T Year: 2016: 12' Knapheide Utility Body, No Sandline, corded Remote, Front Jack Mast Lights. Truck has an Automatic Transmission, Odometer Reads 50,521. Truck Warranty with lots of hours/miles left will Transfer.
Water Truck - SRS #4629
DESCRIPTION: Flatwater Fleet; Model: 2,100 Gallon; Mounted On: 2004 Ford Sterling; Truck Engine Make: Mercedes 435 HP; Condition: Needs Some Work; Tools/Options: 2,100 Gallon Flatwater Fleet: 10,000# Crane (needs Valve Bank). Tank loses about 1/4 Tank of Water in a 24 Hour Period. Engine had Antifreeze in the Oil, Leaking down the side of the engine from Head Gasket. May need complete Engine Block and Pistons. Frame is in Good Condition, Good Transmission and Rearend, Brakes over 50% (brake pedal sticks), Airs up, No Air Leaks, Good suspension. Had a full DOT Feb., 2026. Cab in Good condition, fully in tact, no cracks in dash. Fuel Tanks Emptied and Cleaned in May 2026. Water Tank has 2 cracks in front where frame meets tanks, 2 holes on top needs patch weld. Truck has approx. 216,360 Miles and 4,868 Hours.
Rotary S - SRS #4628
DESCRIPTION: Simco; Model: 2800 HSHT; Compressor: See Below; Mud Pump: Moyno 3L8, Diaphragm; Engine: PTO; Mounted On: 2005 Ford F550 4WD; Truck Engine Make: Powerstroke V8; Condition: Working; Tools/Options: Simco 2800 HSHT Year: 2008: 140# Auto Hammer, 13,500# Pullback, One Auxiliary Winch, 3 Leveling Jacks, 2" Diaphragm Pump. Rig has < 2,000 Hours on it. Truck has approx. 103,634 Miles on it and Toolboxes. 2026 New Rack on the Truck, New Moyno Pump, Replaced the PTO and Repaired the 2 Hydraulic Pumps. Includes a 2003 Ford F550 Flatbed Chase Truck, Dual Axle, 6.0 Engine with approx. 213,000 Miles on it. Runs Strong, A/C, New Rack Installed. Can also Include a Tag Along 185 CFM Compressor that is used for development and also runs the Diaphragm Pump.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |
