Rigs
Pump Hoist - SRS #4543
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 2007 Ford F450 4WD; Truck Engine Make: 6.0 L Power stroke Diesel; Tools/Options: Smeal 5T: No Sandline, has the Plug for a Remote. Truck has a Power stroke Diesel and Automatic Transmission, approx. 66,000 Miles on it. Tailgate and Pipe Racks being put back on.
Rotary D - SRS #4542
DESCRIPTION: 1983, Dresser; Model: T70W; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: CAT 3406; Tools/Options: Dresser T70W Year: 1983: 70K Pullback, Tophead Drive. Runs Range II Pipe, Rod Loader (can preload pipe), 12" Hydraulic Table (hydraulic, hinges up & dies are interchangeable), 4 Drums, 3 Winch Lines. Capable of Retrieving Core Barrels. One Front and Two Rear Jacks. Crane Carrier has some Rust. Had a CAT 4 Mast Inspection in 2014.
Rotary R - SRS #4363
DESCRIPTION: 2023, Reichdrill; Model: RTD 69; Compressor: 1070/375; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: X15 605 HP; Condition: PRICE REDUCED !!; Tools/Options: Reichdrill RTD 69 Year: 2023: Price Reduced. 43,980# Pullback, 160 HS Chain, 35,000# Pulldown, 140 HS Chain, REGEN, Air Operated Holding Wrench with Hydraulic Raising/Lowering, 7-Pod Carousel for 4" X 20' Drill Rod, 8-Gallon Air Line Lubricator, Multicore Cooler, Thermostat Controlled Fan Circuit for Improved Cooling and Fuel Savings, 34' Mast with 28' Stroke, 22" Table Opening, Dual Winches (8,500#), Hydraulically Extendable Jib, Wireless Radio Helper's Remote Controls for Jib Swing, Extend & Retract, Carousel Index/Lock, Winch Up and 2-Speed Winch Down, 20 GPM Water Injection Pump, Torque Limiter Control, Holdback Control, Feed Override all with bypass on & off. Mudline Stand Pipe with Hose Spud & End Cap, Cribbing Rack, 4 Leveling Jacks(36" & 48"), 18 Piece Rod Box, Drill Pipe Lifting Rod, Two Hammer Holders (7" & 10"), Diverter, Hydraulic Welder, Set Up to Run 4" Drill Rod. Capable of Holding 600' of Rod per Owner. Toolbox, Folding Rear Platforms Vandal Cover, Halogen Night Lighting. Truck has an 18-Speed Transmission, Differential Lock, 20K Steerable Lift Axle, Bluetooth, A/C, Heated Mirrors, Aluminum Wheels, Dual 80 Gallon Fuel Tanks, DEF Tank. Includes 1,000' of Rod. Stabilizer holder for the carousel is available but isn't on the rig, taken off to hold 2 more rods. Approx. 601 Hours and 2,100 Miles.. Condition: Near New
Rotary E-F - SRS #3836
DESCRIPTION: 2004, Foremost; Model: DR-24 HD; Compressor: 1070/350; Engine: PTO; Mounted On: 2003 Kenworth Tri-Drive; Truck Engine Make: Cummins 565 HP; Tires: Newer; Condition: Working Drill; Tools/Options: Foremost DR24HD Year 2004: approx. 2,800 Compressor Hours and approx. 9,300 Rig Hours. Gear Driven Lower Drive Casing Rotator. Dual High Torque Tophead, Bean Injection Pump, Hammer Oiler. Work done within 750 Hours: All New Flow Hoses to 3", New Fabco PTO Boxes with Coolers, New Mast Hoist cylinder, Two new Front Tires & 4 New Rear Drives, Full Top End of Motor Redone - head, injectors, Fuel Pump, Fuel Lines, Injection Pump, Turbo, All New Exhaust, Mufflers & Tips. Includes: All Wrenches & Plates, Cyclone with Hoses, 6", 8", 10", 12", 16", 20" and 24" Jaws, 10" Discharge Swivel with Adapters, Spare Sub for 2-7/8" Thread, Full Tophead Seal Kit. Truck has 42,000 Miles on it.
Rotary G - SRS #4393
DESCRIPTION: 2018/19, GEFCO; Model: 40K; Compressor: Sullair 1000/350; Mud Pump: Plumbed; Engine: PTO; Mounted On: 2019 Peterbilt 367 6X4; Truck Engine Make: Cummins 565 HP (recently rebuilt); Condition: Good Working Drill; Tools/Options: GEFCO 40K Year: 2019: Newly Rebuilt Engine (Injectors, Turbo, Oil Cooler), Truck Brake Compressor also Rebuilt. Rig is set up to Run 4.5" X 20' Flush Joint Drill Pipe with 2-7/8" IF Tool Joints and a Holte 350 Casing Hammer. 25K Pulldown, 40K Pullback. 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator, 25,000# Single Line Hydraulic Main Winch over the Jib. Hydraulic Rod Spinner, Modified 60" Breakout Wrench, Auxiliary Winch Mount & Hydraulics (rig has 2 winches, cable recently replaced), 3-Speed Tophead, 15 Piece Rod Box, 6-Rod Carousel, Hammer Holder. Upgraded Joysticks (5-Volt Electric Upgrade), Compressor has approx. 2,300 Hours, approx. 6,000 Total Frame Hours, < 500 Hours on the Newly Rebuilt Engine.. Truck has 22,000# Front Axle, 46,000# Rears, 18-Speed Fuller Transmission. 400' of used pipe included.. Condition: Working Drill
Water Truck - SRS #4448
DESCRIPTION: 2008, Flatwater Fleet; Model: 2,700 Gallon ; Mounted On: 2006 IHC 7400; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Flatwater Fleet 2,700 Gallon Year: 2008: SOLD (2) 110 Gallon Transfer Fuel Tanks all Redone and Painted. 20' Bed Space with Tool Boxes & Fuel Tanks in the Front, 2'6" Tall. Two Brand New Boxes on the Front and Two on the Back in 2024 and Repainted Box, New Lights on the Back with New Brackets, all Maintenance that was needed was also done at that time. Odometer Currently Reads 172,587 Miles, Allison Automatic Transmission (installed a few years ago), low miles on it. Truck is Kept Indoors. SOLD
Rotary G - SRS #4332
DESCRIPTION: 2008, GEFCO; Model: 30K; Compressor: 1000/350 Screw, Heavy Duty PTO with Clutch; Mud Pump: 4X3 Mission NEW; Engine: PTO; Mounted On: 2008 Peterbilt 367 6X4; Truck Engine Make: CAT C15 550 HP; Tires: New - Front; Condition: SOLD; Tools/Options: GEFCO 30K Year: 2008: SOLD Hydraulically Driven Mud Pump with Standard 2-1/2" Piping. (4) Hydraulic Leveling Jacks, Tophead Drive with 70,000 in-lb. Torque, 0-120 RPM, 2-11/16" Water/Air Course, Hydraulic Jib Boom with Dual Controls on Driller & Helper Side. Carousel Holds (6) Pieces of 4.5" X 20' Drill Rod, 2-7/8" IF Tool Joints with Top Breakout Wrench. Hydraulic Cylinder with Cable Pulldown Holdback. 25,000# Pulldown and 30,000# Pullback. Man Winch over Jib Boom, 25,000# Single Line Pull with 3/4" Cable. Line Oiler, 18 GPM Bean 4-Cylnder Hydraulic Powered Water Injection Pump. Single Rod Loader, Helpers Side for Loading Rod under Tophead, Hydraulically Powered Split Table Guide with Air Operated Holding Wrench, Hydraulically Powered 60" Breakout Wrench, Hydraulically Powered Rod Spinner. PL2 Auxiliary Winch with 100' of 3/8" Cable (2,000# capacity), Pipe Rack for 15 Pieces of 4.5" X 20 Drill Rod (slide on outside of pipe rack), (5) Operating Lights, Heavy Duty PTO for Compressor and Hydraulic Pump Drive with Clutch. Side Driller and Helpers Platforms. Truck has 22,000# Front Axle and 46,000# Rears, Fuller 18-Speed Transmission, (2) Fuel Tanks (70 & 150 Gallon), A/C, Jake Brake, Alcoa Aluminum Wheels. Includes approx. 640' of Drill Rod, Breakout Wrench, Lifting Plug, CAT Fuel & Oil Filters, CAT Engine Oil, Side Air Filters, Old Mud Pump that was Replaced (needs small weld patch). Recently changed fluids, filters. New batteries and some new hoses. Carousel Activator is not Working, needs Repaired. Mud Puppy Available for an Extra Cost.
Rotary D - SRS #4456
DESCRIPTION: 1986, Driltech; Model: T40K2H; Compressor: Sullair 1000/350; Engine: CAT 3406; Mounted On: CCC; Truck Engine Make: Diesel; Condition: Good Running Drill; Tools/Options: Driltech T40K2H Year: 1986: Rig is Set Up to Run 3.5" Drill Rod. M&R: One Link Removed from the Chains, Replaced the Top of the Bean Water Injection Pump and Installed a Piston Kit, New Master Links on the Chains to Tophead, Repaired Bushing Holes & New Bushings in the Tophead Plates, Replaced Detent Springs on the Feed Spool Control Handle, Rebuilt Tophead, New Bull Shaft, Bearings, Planetary Parts, Seals & O-rings. Filled with 75W-90 Full Synthetic Gear Oil, New Water Injection Hydraulic Hoses, Replaced Numerous Hoses, Welded Crack on Hydraulic Tank Outlet Port, Repaired Main Pump Seal & Shaft, Replaced Hoses in the Rear Cabinet, Full DOT, New Pressure Relief Valve, Welded up Cracks on the Mast Support Tubes, Valve Kit on Rear Valve Bank, New V-belts on the Chassis Engine, Reman on Alternator, New U-joint on the Chassis Drive Line, All Air Filters Changed, New Oil Pressure Switch on the Deck Engine, All New Oils & Coolant, Rear Rearend Rebuilt on the Chassis, New Oil in the Rear Ends, Couple of New Circuit Breakers, New Hydraulic Oil Filters and Oil, Deck and Chassis Coolant Filters, Temp Switch on the Deck Engine, New Air Dryer on the Chassis, Air (on/off) Cylinder Rebuilt, New Air Filter Cover, Checked Rod Carousel.. Condition: Good Running Drill
Rotary G - SRS #3914
DESCRIPTION: 1975, Gardner Denver; Model: 2000; Mud Pump: GD 7-1/2" X 10"; Engine: PTO; Mounted On: 4-Axle Crane Carrier; Truck Engine Make: 400 Cummins; Tools/Options: Gardner Denver 2000 Year: 1975: 58' Mast, 10" Retractable Rotary Table, Air Clutches, Two Drum Machine, No Sandline, No Rod Rack, 4-1/4" or 4-1/2" X 38' Hex Kelly (needs confirmed), Rig is set up to run 30' Rod. Has a Large Gardner Denver Swivel that has been Rebuilt, 2 Wells since. Has a Winch on the Side for Oil Field Dogs. Also Includes 810' of 5" X 30' Drill Rod with 3-1/2" IF Threads (used on 6 wells) and a Rod Trailer that was Purchased New and has < 300 Miles on it. Can be sold without rod.
Mud Grout Pumps - SRS #4541
DESCRIPTION: Mud Pump: 2023 Gardner Denver 5X6 FXG 172; Mounted On: Unmounted; Condition: Never Used; Tools/Options: Gardner Denver 5X6 FXG 172 Year: 2023 New, Never Used Gardner Denver 5X6 Mud Pump.
Rotary R - SRS #4493
DESCRIPTION: 1996, Reichdrill; Model: T-650 W II; Compressor: 1150/350; Mud Pump: None; Engine: CAT 3406B; Mounted On: 1996 Ford LT-8000; Truck Engine Make: Cummins 300 HP; Condition: Good; Tools/Options: Reichdrill T-650 W II Year: 1996: Brand New Compressor with approx. 140 Hours on it. Newer Upper and Lower Chains. 38,000# Rated Pullback Capacity, HD 160# Chains, 26,000# Down Pressure, Standard 140# Chains, Chains are about 2 years old, Spare Chain Parts Included. 34' Mast, (2) 4.5" Hydraulic Mast Raising Cylinders, Hydraulic Retractable Table, Carousel Holds 7 Rods, Hydraulic Breakout Wrench, 4-cylinder Bean Water Injection Pump, (2) Rear 36" and (1) Front 48" Leveling Jacks. New Valves on Top of Jacks, New Water Injection Control Valve. 3,000 psi Capacity Water Injection Pump Valve, Hydraulic Winch, Jib Boom, Rod Rack Capable of Holding (12) 4.5" Rods, Night Lights. Deck Engine has a New Starter and Newer Injection Pump, New Tach Installed a few Years Ago. Serviced every 200 Hours including the Funk Oil and Air Filters. Carousel and Rod Box Included but not on the Rig. Rig is set up to run 4.5" x 20' X 2 7/8 IF" Drill Pipe, Hour Meter Reads approx. 8,170. Truck has a 9-Speed Fuller Transmission,18,000# Front Axle, 46,000# Rear Axle, Hendrickson Suspension. Truck Engine has approx. 73,066 Miles on it. Includes a New, Full Set of Front and Rear Tire Chains. Rig is Operational. Includes J-Wrench, 48" Tongs, 48" Breakout Wrench, Rod Bushing, 6" and 8" Slips. Welder in Photo Not Included. Atlas 2000 Casing Hammer Available at an Extra Cost. Rod Box and Carousel Included.
Rotary T-Z - SRS #4368
DESCRIPTION: 2009, Versa Drill; Model: 100NG; Compressor: 500/200; Mud Pump: Mission 250 Series 3X4X13 & a Failing 5X6 Duplex; Engine: PTO; Mounted On: 2009 Peterbilt; Truck Engine Make: Diesel; Condition: PRICE REDUCED; Tools/Options: Versa Drill 100NG Year: 2009: 40K Pullback, Hydraulic Jacks, Main Winch & Sandline Winch,11-Rod Carousel, 2 3/8” ID with FEDP Threads 3” OD X 20' Pipe, Mission 250 Series Centrifugal Mud Pump with a 4" Discharge and a 5X6 Failing Duplex Pump, Hydraulic Quick Connects to Swap Two Hoses and Switch Between the Two. Truck has a Jake Brake, Manual Transmission, AC, Three Toolboxes, Odometer Reads 367,668 Miles and 18,380 Hours. Includes 400' of 3" X 20' Heavy Wall Pipe (will have New Box Ends & Tool Joints Replaced), (2) Drill Bit Subs (1) 6-5/8" API Regular Box Fish Necked to 3" OD FEDP 2-3/8" Box with 2-7/8" Tool Joints for Breaking, (1) 4-1/2" API Regular Box Fish Necked Down to 3" OD FEDP 2-3/8" Box with Tool Joints for Breaking. Rebuilt Fabco 200 Transfer Case is Available for an Extra Cost (0 hours). EXTENSIVE LIST OF M&R AVAILABLE.
Rotary A-B - SRS #4050
DESCRIPTION: 2016, Atlas Copco; Model: TH-60; Compressor: 1070/350; Mud Pump: Removed; Engine: PTO; Mounted On: 2014 Peterbilt 367; Truck Engine Make: Cummins ISX 600 HP - FACTORY NEW; Tires: NEW 95%; Condition: Working Drill Many Upgrades; Tools/Options: Atlas Copco TH-60 Year: 2016: 40K Pullback 30K Pulldown, 4,400 ft.-lbs. Maximum Head Torque, 2-Speed Head Rotation, 18,000# Winch, Hammer Lubricator, 7-Rod Carousel, Rig is Set up to Run 4.5" X 20' Drill Rod with 2-7/8" IF Rod, Rod Box Holds 18 Joints of Drill Rod, Bean 25 GPM/750 psi Water Pump. Truck has Two Fuel Tanks (150 and 85 gallon), Jake Brake, 19-Speed Eaton Transmission 68,000# GVWR, 22,000# Front Axle and 46,000# Rears. 425/65R22.5 Front Tires and 11R22.5 Rears. Recent Repairs and Upgrades: Top Breakout Wrench, Two New Lift Cylinder Pins on Mast, FACTORY NEW Cummins Engine, Gearbox Replaced with Newer Style Nimco, Installed Sandline, Single Rod Loader, New Cables, Brakes, Tires, Rod Spinner, Controls & Gauges Gone Though, Repaired. New Carousel Installed and Rollers in Shaft were Replaced with the Big Rollers. New Main Head, New Swivels & Pins, New Carousel, Replaced Seals & Bearings in Gearbox on Bottom, New Table Bushings. Electrical Control Box was Replaced, Grounded, Dash Wires all Gone through. All Work was either professionally done or Parts were Purchased New. Drill Rod Available, Diverter Optional. Currently has 38,278 Miles, 1,086 Engine Hours and 4,913 Compressor Hours.
Water Truck - SRS #4305
DESCRIPTION: Water Truck; Mounted On: 1998 Volvo Auto Car; Truck Engine Make: CAT 3406E 475 HP; Condition: PRICE REDUCED; Tools/Options: 2,200 Gallon Tank that has been Sandblasted and Painted. 20' Bed, 200 Gallon Fuel Transfer, IMT 2020 Teathered Control Crane. Truck has an Eaton Fuller 8LL Transmission, Jake Brake, 46K Full Locking Rears. Runs Strong, Doesn't Burn Oil or Blow Smoke, Miles Unknown
Rotary G - SRS #4517
DESCRIPTION: 2023, GEFCO; Model: 30K; Compressor: 1050/350; Mud Pump: 3" Wilden; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: Cummins 565 HP; Condition: Great; Tools/Options: GEFCO 30K Year: 2023: Holds 6 Rods in the Carousel and 15 in the Rod Box. Single Rod Loader, Rod Spinner, Hammer Holder, Foremost Shock Sub. Some Warranty Left out of the 5 Year Warranty. Rod that drill can hold is included along with a used 6" QL6 Hammer and an 8" Rebuilt Hammer with 8-3/4" Hammer Bit and a 8-3/4" Roller Bit with 15' Sub, 5-7/8" Roller Bit for Cleanout, Stabilizers, Bit Breakers, Slips, Pipe Lifters, 10-12 Bags of Mud. Also Includes a Water Truck (2) 20' Hoses, No Fuel Tank on the Truck but has a 120 Gallon Tank with an Electric Pump that could be Included. Rig is Set Up to Run 4.5" X 20' X 2-7/8" Drill Pipe. Hub Odometer Currently Reads 10,977 Miles, Total Rig Hours - 2,313 and Current Compressor Hours are 1,222.
Rotary G - SRS #4433
DESCRIPTION: 2016, GEFCO; Model: SS-22 RC HD; Compressor: DR 500/200; Mud Pump: 6X5X14 National; Engine: PTO; Mounted On: 2015 Peterbilt 367; Truck Engine Make: Cummins ISX15 525 HP; Tools/Options: GEFCO SS-22 RC HD Year: 2016: Telescoping Jacks, Original Build Sheet Shows 18" Failing 150 Ton Rotary Table, 6" Western Rubber Swivel, 6" Western Rubber Air Side Inlet, 23' Kelly Bar, 7" Dual Outside Air Flange Ends, 4-Part Kelly Line with14" Block, 4-Part Pipe Line with 14" Block, Sandline, 15' Mast Extension, 6" Swivel. Truck Odometer Reads 14,854 Miles and 5,206 Hours. Compressor needs a new air end. Some Flange Connection Outside Air Drill Pipe Available for an Extra Cost.
Auger - SRS #4394
DESCRIPTION: 2002, Mobile; Model: B61HDX; Engine: 4BT Cummins; Mounted On: 1992 Ford F800 2WD; Truck Engine Make: Ford 7.8L 210 HP; Condition: SOLD; Tools/Options: Mobile B61HDX Year: SOLD 2002: 3L8 Moyno Water Pump, In/Out, Side to Side Wiggle Tail, Main, Auxiliary & Saf-T-Driver Winches, 3 Outrigger Jacks, 2 Swingout Auger Storage Racks. Truck has approx. 156,000 Miles on it. Tooling in Photos Included. SOLD
Mud Grout Pumps - SRS #4538
DESCRIPTION: Mud Pump: GASSO 1654C 5X8; Engine: Detroit 471; Mounted On: Skid; Condition: Rebuilt; Tools/Options: GASSO 1654C 5X8: 250 Gallon Diesel Tank. New Expendables Included but not Installed. Enclosed Chain in Box, Enclosed Chain from Engine to Pump. 5-Speed Transmission (high pressure, low fluid).
Steel - SRS #4537
DESCRIPTION: Ingersoll Rand; Tools/Options: 500' of 4.5" X 20' Ingersoll Rand Drill Rod with 3.5" Connections. T4 Hex/Squares. Calipers a full 4.5" but some Pitted from Sitting.
Steel - SRS #4535
DESCRIPTION: Ingersoll Rand; Condition: Good; Tools/Options: Ingersoll Rand: Near New Ingersoll Rand 4.5" OD X 30' Drill Rod with 2-7/8" Threads. Approx. 1,020' (34 joints) Available.
Mud Grout Pumps - SRS #4534
DESCRIPTION: Mud Pump: Gardner Denver 5-1/2" X 8"; Engine: See Below; Condition: Rebuilt; Tools/Options: GD 5-1/2" X 8": Completely Rebuilt Except for Bull Gear which is in Good Condition. New Expendables, Bearings, Liners, Rods, Pistons, Valves, Valve Seats. Equipped with a Shaft so it can run off of an Engine, Hydraulically or with a Pulley and Belt.
Mud Grout Pumps - SRS #4533
DESCRIPTION: Mud Puppy; Model: MP-255-25C; Engine: 73.9 HP Deutz; Mounted On: 2008 Heavy Duty Trailer; Condition: Runs and Works Great; Tools/Options: Mud Puppy MP-255-25C Year: New Deutz Engine Installed with 380 Hours on it and New Hydraulic Pump. Includes Extra Parts. Runs and Works Great.
Rotary G - SRS #1967
DESCRIPTION: Gardner Denver; Model: 3000; Mud Pump: 7-1/2 X 10 GD; Engine: (2) Detroit 6V71 Rebuilt in 2019; Mounted On: 6 Axle CCC; Truck Engine Make: 871T; Condition: Excellent; Tools/Options: Gardner Denver 3000 : Operating Daily! Re-manufactured in 2006. Double Drum with Sandline - 3 Drum line (no need for rathole), Kelly Track in the Derrick. Fast Drilling, Easy Removeable Table. 60' Racking Board. 1 deck engine drives the mud pump and the other engine drives the Drawworks. 70' mast, telescopes to 97', rated @ 250,000# with 100 ton Webb traveling block with 1" cables. 4" King swivel with 4-1/2" IF X 37' fluted Kelly. 18" Brewster Skytop oilfield table. (2) BJ breakout tongs, air clutches, (6) hydraulic jacks (4) screw jacks, 50 ton McKissick block (Kelly), operators platform. 4-5 yrs. old since completely rebuilt from ground up. Includes all the standards - elevators, slips, bushings. Has set 36" Casing, Table Lifts Out with Sling. Deck Engines Rebuilt in 2019. All 4 Rear Axles Pull.
Rotary H-I - SRS #4532
DESCRIPTION: 2001, Ingersoll Rand; Model: T3W; Compressor: 1070/350; Mud Pump: Wilden QLX-6; Engine: CAT 3406E; Mounted On: 2000 Mack; Truck Engine Make: E7; Condition: Very Good; Tools/Options: Ingersoll Rand T3W Year: 2001: Wilden Mud Pump is 3 Months Old, piping to Boss Fitting Swap Location. Truck has approx. 38,000 Miles on it. Includes 400' of 4" Drill Rod. Approx. 13,000 Total Rig Hours, Compressor Hours Unknown. Rebuilds Unknown. Manual Clutch for when Starting the rig. A 1997 Freightliner with 2,000 Gallon Flat Tank is Available for an Extra Cost. PBA CAT 3126 which was rebuilt about 4 years ago before purchased. 10-Speed with Jake Brake, Full Locking Rears, 200 Gallon Fuel Tank.
Rotary S - SRS #4401
DESCRIPTION: 2001, Schramm; Model: T450WS; Compressor: Sullair 900/350 w/ Clutch; Mud Pump: Mission Magnum; Engine: CAT 3206; Mounted On: 2001 IHC 6X4; Truck Engine Make: Diesel; Tools/Options: Schramm T450WS Year: 2001: Pullback 30,000#, Pullback, 17,000# Pulldown. Dual Tophead Motors, 28'6" Mast Travel. Four Outriggers, Braden PD15 Winch, 15,000# Capacity. 10-Rod Carousel, Rig Holds 480' of 3-1/2" X 2-7/8" X 20' Drill Pipe, Hydraulic Table and Break-out Wrench (48" but cant take 60"), 205 Gallon Fuel Tank, Hammer & Stabilizer Holder, Sliding Tophead, Water Injection, Pipe Rack, Jib Boom with Hydraulic Swing, No Sandline. Truck has 56,000# GVWR, 16,000# Front, 46,000# Rears. CAT 3206 Deck Engine Rebuilt (Sept 2024),Tophead also Rebuilt (Nov. 2024). Currently having a New Mast Installed. Service Records Available. Compact Drill Good for Geothermal and Mineral Exploration. Truck Odometer Reads 003,300.4 Hours. Compressor Hours Unknown. Truck Odometer Miles 077,103.9. No Rod & Tooling Included. Currently having a new mast installed. OFF MARKET, PUT BACK TO WORK
Pump Hoist - SRS #4512
DESCRIPTION: 2016, Hunke; Model: 6T; Engine: PTO; Mounted On: 2016 Ram 5500 4WD; Truck Engine Make: Cummins 6.7L; Tools/Options: Hunke 6T Year: One Owner, Sandline with approx. 1,000' of Cable, 3 Outriggers, Hunke Tilting Pipe Racks. Owner believes there is a wired remote. Truck is Equipped with Power Windows, AC and has approx.. 98K Miles. 11' Palfinger Bed, Spray in Bedline. There is Moderate Damage to Driver Side Front Corner, Swiped 6 Years Ago. The Door was modified to close securely and was used daily in it's current state.
Auger - SRS #4531
DESCRIPTION: 1995, CME; Model: 55; Engine: Deutz 5-Cylinder; Mounted On: 2014 IHC SBA 4300 4X2; Truck Engine Make: Diesel; Condition: Working Rig; Tools/Options: CME 55 Year: 1995: 3,200# Mainline, (2) 1,800# Winch lines (fast/slow), Auto Hammer. Cathead is not mounted but available, (3) Jacks, Wiggle Tail. 3L8 Pump and Water Tank are both Trailer Mounted Making the Rig under CDL. Truck Odometer Reads 225,686. No Rod or Tooling Available.
Sold - SRS #4370
DESCRIPTION: Flatwater Fleet; Model: 2,400 Gallon; Mounted On: 2008 IHC 7600; Truck Engine Make: CAT C13 410 HP; Condition: SOLD; Tools/Options: Flatwater Fleet: 2,400 Gallon Flatwater Fleet Flat Tank, 30' Remote Stellar Crane. (2) 100 Gallon Fuel Tanks on the Deck with a Transfer Pump & Numerous Tool Boxes. Truck has an 18-Speed Transmission, Air Ride Suspension and Both Seats have Air Ride, Jake Brake, Full Lockers, approx. 109,000 Miles on it. 18k Front and 46K Rears, 64K GVWR. SOLD
Rotary S - SRS #4510
DESCRIPTION: 1982, Speedstar; Model: SS 135 HD; Compressor: Yes, Developmental - To Be Confirmed; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2006 IHC 7600; Truck Engine Make: Cummins ISX 15; Tires: New; Condition: Working Daily; Tools/Options: Speedstar SS 135 HD Year: 1982: Hydraulic Drawworks Rebuilt 6-8 Years Ago, Painted approx. 5 Years Ago. Mud Pump Had Gear End Rebuilt Two Years Ago and Fluid End about 6 Months Ago (2025), 4-Part Kelly Line and 4-Part Trip Line. Newer 3-3/4" Fluted Kelly with Drive Bushings. Four Leveling Jacks and has Pulldowns. All Hydraulically Driven except for Air Clutches. Hydraulically Driven 8-1/2" Rotary Table Rebuilt a Few Years Ago, Chain Box Completely Rebuilt 4 Years Ago. New Motor 4 Years ago (2021) New Clutch and 8 Brand New Tires, New Tranny. Bearings out on the Air Compressor Drive Clutch, has all the parts, just needs rebuilt. New Gauge Cluster was Installed when Engine and Drill was Installed on the IHC Chassis. Includes 400' of 3.5" Flush Joint Drill Pipe with 2-3/8" IF Threads. Truck has an 8-Speed Transmission and approx. 200,000 Miles on it. Engine and Transmission has approx. 80,000 Miles since Engine and Clutch was Replaced.
Pump Hoist - SRS #4516
DESCRIPTION: 2024, TDH; Model: 6X2; Engine: PTO; Mounted On: 2024 Ford F600 4WD; Truck Engine Make: 6.7L Power Stroke Diesel; Condition: Working Unit; Tools/Options: TDH 6X2 Year: 2024: Two Line Machine, Remote. Power Stroke Diesel Engine, Extra Rear Springs, approx. 17,000 Miles on Truck, Subject to Change. All Aluminum Boxes, Three Leveling Jacks. Working Unit. No Mechanical Issues.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
Rotary D - SRS #4291
DESCRIPTION: 1995, Driltech; Model: T40KW3 Long Tower; Compressor: 1160/350; Mud Pump: 5-1/2" X 8" Gardner Denver; Engine: Cummins K19 600 HP; Mounted On: 1994 CCC with Lift Axle; Truck Engine Make: Cummins 350; Tires: Good; Condition: Well Maintained; Tools/Options: Driltech T40KW3 Long Tower Year: 1995: 600 HP Deck Engine, Long Tower, Hydraulically Driven Mud Pump, 20" Table Opening. 2-Speed Tophead (0-50 rpm @ 120,000 in/lb. & 0-150 rpm @ 92,000 in./lb.), 2.25" Pulldown Chains, Mast has a 34' Stroke, Inner & Outer Carousels, each Carousel holds (6) 4.5" X 25' Rods. One Exception on the outer carousel, a surface collar sits in one of the rod pods, The top of the collar is the same as the 4.5" Drill Rods so no change needed there. The Bottom has a Larger Pod that Sits above the original rod socket so it can easily be removed to facilitate a regular 4.5" rod. Heavy Duty Pulldown, Upgraded to the 70,000# Pullback and Installed 7.25 cu/in Rotation Pump, Tophead is Heavier Duty than a Standard D40K, Built with High Ambient Cooling for Engine, Hydraulic & Compressor Fluids, Rated for 130° F Conditions. 25 GPM Injection Pump. Includes 275' of 4.5" X 25' Drill Pipe with 2-7/8" IF Threads, 23' Surface Collar, Mud Pit. Can be sold without mud pump.. Condition: Well Maintained
Rotary A-B - SRS #4527
DESCRIPTION: 2007, Atlas Copco; Model: T2W; Compressor: See Below; Mud Pump: None; Engine: PTO; Mounted On: IHC 7600 6X4; Truck Engine Make: CAT C13 ACERT; Tools/Options: Atlas Copco T2W Year: 2007: ex military drill. Truck has an Eaton Fuller 10-Speed Transmission, 380 HP Engine, Winch on front bumper and approx. 85,000 Miles on it. Sand Reel, Jib, Rod Box, Downhole Lubricator, Single Rod Loader. No Rod or Bits Available. Truck is extremely clean. Drill has 2500 Original Hours and was being used with an auxiliary air compressor. There is a U-Joint on the PTO to accommodate another accessory, possibly a compressor. Two Switches on the Control Panel need Replaced. At one time rig had a hydraulically driven mud pump on board.
Steel - SRS #4530
DESCRIPTION: Chicago Pneumatic; Tools/Options: 500' of CP Style Drill Rod. 3.5" O.D. X 20'.
Auger - SRS #4177
DESCRIPTION: Ardco; Model: Super L Mini Buggy; Engine: PTO; Mounted On: Ardco Buggy; Truck Engine Make: 4-Cylinder Isuzu Diesel; Tires: New; Condition: Runs Great; Tools/Options: Ardco Super L Mini Buggy: NP 4-Speed Transmission, Rockwell TRRT-32-79 Transfer Case, Bumper Mounted, PTO Driven Ramsey 400-L Winch, 3-Stage Commercial Hydraulic Pump, 14' Lockable Mast, Hydraulic Hoist Drum, Rod/Auger Rack. This Unit is Currently set up for Auger Drilling but Could be Converted to Mud Rotary with the Addition of Swivel and Mud Pump (not included). Runs Strong and is Light and Fast. Easily Hauled and Mobilized. Recently had New Tires Installed, New Radiator, New Hub along with the Hydraulic Pump being Replaced and completely Cleaned & Replaced the Hydraulic Fluid.
Sold - SRS #3899
DESCRIPTION: 1989, Mobile; Model: B47; Engine: John Deere; Mounted On: 2009 Ford F450XL Super Duty 4X4; Truck Engine Year: 6.8L; Condition: SOLD; Tools/Options: Mobile B47 Year: 1989: SOLD Two Winches, 3L6 Moyno Pump, Cathead (new rope 2021), 16' Mast, has run up to 6" auger on it, 140# Safety Hammer, approx. 170K Miles on the Truck. Truck Recently had the Engine and Transmission Replaced. Lots of Tooling Included (drive cap, adapter, 10 joints of 5' AWJ, 9 joints of 2-1/4" Auger, plug, bit, cutterhead, bit spade, hoist plug, sampler, retainer basked, sampler shoe, 3" X 30" shelby tube with caps, sample extruder assembly). Also available for an extra cost, 30' of 2.5" solid stem augers with pins and catcher that are brand new and only use some of them once or twice. Was being used for Shelby Tube Work. SOLD
Sold - SRS #4529
DESCRIPTION: Model: 3T; Engine: 4-Cyl. Wisconsin; Mounted On: 1997 Ford; Truck Engine Make: Gas; Tires: Okay; Condition: Working Unit; Tools/Options: 3T: New Hydraulic Hoses, Valve Bodies Rebuilt, New Hoist Cable, Deck Mounted Wisconsin Motor, Power Hoists. No Sandline. Truck has approx. 78,000 Miles on it. No Rust.
Mud Grout Pumps - SRS #4528
DESCRIPTION: Geo-Loop; Model: 50-500; Engine: 25 HP Honda; Mounted On: Skid; Tools/Options: Geo-Loop 50-500: Includes Hose Reel. Unit has approx. 800 hours on it.
Rotary S - SRS #4526
DESCRIPTION: Simco; Model: 2800; Mud Pump: Moyno 6L; Engine: PTO; Mounted On: 2005 Ford F550 4WD; Truck Engine Make: Powerstroke V8; Condition: Good Working Condition; Tools/Options: Simco 2800: 140# Auto Hammer, 13,500# Pullback, One Auxiliary Winch, 3 Leveling Jacks, approx. 1,783 Rig Hours. Truck Currently has 102,790 Miles on it, Toolboxes. Includes a 2003 Ford F550 Flatbed Chase Truck, Dual Axle, 6.0 Engine with 212,000 Miles on it. Runs Strong, A/C.
Water Truck - SRS #4524
DESCRIPTION: Rosewall; Model: 2,500 Gallon; Mounted On: Unmounted; Condition: Good; Tools/Options: Rosewall 2,500 Gallon Unmounted: Stainless Steel Tank/Body, Multiple Tool Boxes, Bulk Gravel Box
Parts Tooling - SRS #4523
DESCRIPTION: Atlas Copco - EPIROC; Tools/Options: Blast Hole Drilling Rig Parts, some are Used/Like New and some are Surplus/New. Owner Believes the are for a L8 Rig and DHR Series Epiroc FlexiRoc.
Mud Grout Pumps - SRS #4522
DESCRIPTION: Mud Pump: Gardner Denver 5X6; Tools/Options: Gardner Denver 5X6 Air Operated Mud Pump. Used approx. 4 Times since Rebuild.
Steel - SRS #4521
DESCRIPTION: Tools/Options: Approx. 600' of Ingersoll Rand 3.5" X 20' Used Drill Rod.
Sold - SRS #4463
DESCRIPTION: 2003, Ingersoll Rand; Compressor: IR 750/175; Engine: Cummins; Mounted On: Tag Along - Pull Behind; Condition: SOLD; Tools/Options: Ingersoll Rand 750/175 Year: 2003 Cummins: 1,566 Hours. SOLD
Pump Hoist - SRS #4520
DESCRIPTION: 2008, Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F450 4WD; Truck Engine Make: Diesel; Condition: Working Unit; Tools/Options: Smeal 5T Year: 2008: Manual Transmission, Sandline, Remote. Bed has some rust on it. Odometer Reads 164,481.
Water Truck - SRS #4519
DESCRIPTION: Montana Flat Tank; Model: 2,000 Gallon; Mounted On: 1996 Kenworth; Truck Engine Make: CAT C12; Condition: OFF MARKET; Tools/Options: Montana Flat Tank 2,000 Gallon: 2,000 Gallon Water Bed. Super 10 Transmission, 200 Gallon Fuel Tank. Truck has 879,000 Miles on it. Grouter Not Included. OFF MARKET
Rotary G - SRS #4515
DESCRIPTION: 2020, GEFCO; Model: 40K; Compressor: 1070/350; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: Peterbilt; Truck Engine Make: Cummins ISX 605 HP; Condition: Great; Tools/Options: GEFCO 40K Year: 2020: 1,038 Hours on Compressor, 5,374 Hours on the Engine.
Rotary H-I - SRS #4518
DESCRIPTION: 1985, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Engine: PTO; Mounted On: 1988 Paystar 5000; Truck Engine Make: 8V92T Detroit; Condition: Working Drill; Tools/Options: Ingersoll Rand TH-60 Year: 1985: 13-Speed, All New Drive Lines, Transfer Box has been Rebuilt. Detroit and Air Compressor have been Replaced. Lots of New Hydraulic and Air Hoses. Machine has been Refurbished. Includes a 1996 IHC 2674 Truck with a 2,200 Gallon Water Bed, 200 Gallon Diesel Tank on Headboard, Overall Bed is 25', Rod can go under headboard, IMT Crane with Corded Remote, Powered by a N14 Cummins Engine. 8LL Transmission, 3-Stage Jake Brake, 8 New Tires on Rear. 400' of Drill Rod Available for an Extra Cost. Will Sell Drill Separate from Water Truck.
Rotary E-F - SRS #4471
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6; Engine: PTO; Mounted On: 1990 IHC; Truck Engine Make: DT 466; Condition: PRICE REDUCED; Tools/Options: Failing 1500: PRICE REDUCED! Retractable Drawworks, Heavy Duty Mast, Fabricated Table (can remove top plate to install surface casing), No Kelly Included, 42' Mast, Set up to Run 2-7/8" External Upset Drill Pipe with Lugs, Four Jacks. Truck has 188,419 Miles on it. Drill Rod, Slips to fit table and Two Older Parts Rigs Available for an Extra Cost.
Rotary E-F - SRS #4470
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6 with Air Clutch; Engine: PTO; Mounted On: 2006 Freightliner; Truck Engine Make: CAT C7; Condition: PRICE REDUCED; Tools/Options: Failing 1500: PRICE REDUCED! Fluid End on Mud Pump Needs New Liners and Pistons. Newly remanufactured Drawworks, All Retractable, Heavy Duty Mast, Heavy Duty Mechanical Breakout Table - Chain is Broken -Assembly C2201-D, 2-7/8" X 27' Long Kelly, 42' Mast, Sandline with 1/2" Cable. Rig is Set up to run 2-7/8" External Upset Drill Pipe with Lugs. Front and Rear Jacks, Operators Platform, Pipe Rack. Approx. 344,193 Miles on Truck. Drill Rod, Slips and Two Older Parts Rigs Available for an Extra Cost.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |