Rigs
Rotary S - SRS #4584
DESCRIPTION: 1989, Schramm; Model: T-660H; Compressor: 900/350 GHH; Mounted On: 2009 Mack Granite 6X4; Truck Engine Make: 485 HP; Condition: Good; Tools/Options: Schramm T-660H Year 1989: Rig is Capable of Holding 280' of 4.5" Drill Rod Standing up between the Lazy Susan and Rod Rack on the Side of the Mast. Rig has an 18" Table Opening. 40K Pullback, 30' of Travel as well as a Foremost Floating Sub. New Upgraded Piggyback Pump & Rotation Pump (2021), Deck Engine Completely Rebuilt in 2019, Upgraded Hydraulic Pumps, New Preheat Deck Engine Heater in 2022, Added Helpers Side Controls for Winch and Jib Boom. Compressor also Rebuilt around the same time as the deck engine (2019), best guess on hours is approx. 3,000. Truck has an 18-Speed Transmission and approx. 46,345 Miles, Routine Maintenance done Yearly, New Injectors in 22/23. Previous Owner Purchased the Truck New.
Auger - SRS #4583
DESCRIPTION: Estimated to be a 1982 +/-, Mobile; Model: B47; Mounted On: Morooka Tracks; Tools/Options: Mobile B47: Year Model Estimated to be a 1982 +/-. Safety Driver, Moyno Water Pump.
Rotary G - SRS #4578
DESCRIPTION: 1975, Gardner Denver; Model: 1400; Compressor: GD 667; Mud Pump: 5X6 Belt Driven; Engine: PTO; Mounted On: 2001 Paystar; Truck Engine Make: Cummins; Tools/Options: Gardner Denver 1400 Year: 1975: Retractable Table, 16" Opening, (4) Jacks, Square Tube Derrick, 1400 Air Clutch Drawworks.
Pump Hoist - SRS #4569
DESCRIPTION: 2004 REFURBISHED IN 2025, Pulstar ; Model: P10; Engine: PTO; Mounted On: 2021 Ford F550 2WD; Truck Engine Make: 6.7 L Diesel; Tools/Options: Pulstar P10 Year: 2004: Pump Hoist Refurbished in 2025, Wired Remote, After Market Pipe Racks, Sandline with 1,000' of New Cable. Built in Mud Mat Holder for 8X3 Mats. Available for an extra cost: 15 Mats, Miller Bobcat Welder with 100' Leads. Truck has 35,000 Miles on it (1,503 engine hours), Power Everything, solid Truck. Brand New 12' Flatbed Body. New PTO & Pump. Tool Boxes can be Added for Extra Money. Can be sold with or Without Extra Equipment Listed.
Pump Hoist - SRS #4581
DESCRIPTION: 2022, Pulstar; Model: P12HRPPGXF; Engine: PTO; Mounted On: NEW 2024 Ram 5500 4WD; Truck Engine Make: 6.7 L Cummins; Tools/Options: Pulstar P12HRPPGXF Year: 2022 - 48' Tower, Hydraulic Outriggers, Wireless Remote, Aluminum Pipe Racks with New Rack Straps. 1/2" X 155' Mainline Cable, 7 Ton Hook, New Tailout Cable - 3/8" X 125' - 3 Ton Hook. Extra Large Front Jack, Hydraulic PTO, LED Mast Lights, Hydraulic Oil Cooler, HD Tailgate, 11' Reading Service Body with LED Lights, Power to Rear for a Wire Winder, 11" HD Tow Bumper, Able to Accommodate a Welder/Generator. Unit was inspected in Feb 2026 and everything was satisfactory. Remote Control Adjustable Response. Turbo Diesel Truck Engine, Automatic Transmission, Locking Differential, A/C, Backup Camera, Tilt, Cruise, HD Rear suspension, Power Windows and Locks, SS Wheel Simulators. Odometer Reads 176 Miles. 5 Year 100K Mile Warranty on Truck.
Auger - SRS #4577
DESCRIPTION: 1997, Diedrich; Model: D120; Mud Pump: Moyno 3L8; Engine: PTO; Mounted On: Buggy; Truck Engine Make: JD 6059;
Rotary C - SRS #4576
DESCRIPTION: Chicago Pnuematic; Model: T-650 WS; Compressor: 825/250; Engine: CAT 3406 A; Mounted On: 1978 Ford; Truck Engine Make: Diesel; Condition: Good; Tools/Options: Chicago Pneumatic T-650 WS: Brand New Compressor in 2025. Rig is in Very Good Condition for the Age. 500' of 4.5" Drill Rod and an Atlas Casing Hammer Available for an Extra Cost.
Rotary G - SRS #4560
DESCRIPTION: 2015, GEFCO; Model: 30K; Compressor: Sullair 1000/350; Mud Pump: 4X3 Centrifugal; Engine: PTO; Mounted On: 2015 Peterbilt 367 6X4; Truck Engine Make: Cummins ISX15; Condition: Good, Working Drill; Tools/Options: GEFCO 30K Year: 2015: 40,000# Tophead Drive Pullback Capacity, Main Hydraulic Winch with 20,000# Single Line Capacity, 40,000# on 2-Part Line, 6-Rod Carousel Set Up for 4.5" O.D. X 20' X 2-7/8" I.F. Drill Pipe, Single Rod Loader, FMC 18 GPM Water Injection Pump, 7 Gallon Capacity DHD Lubricator, 4 Hydraulic Outriggers, Pipe Spinner. Compressor Hour Meter Reads 2,650 Hours, Truck Odometer Reads 41,180 Miles. 400' of Drill Rod Included.. Condition: Working Drill
Rotary S - SRS #4526
DESCRIPTION: Simco; Model: 2800; Mud Pump: Moyno 6L; Engine: PTO; Mounted On: 2005 Ford F550 4WD; Truck Engine Make: Powerstroke V8; Condition: Good Working Condition PRICE REDUCED; Tools/Options: Simco 2800: 140# Auto Hammer, 13,500# Pullback, One Auxiliary Winch, 3 Leveling Jacks, approx. 1,783 Rig Hours. Truck Currently has 102,790 Miles on it, Toolboxes. Includes a 2003 Ford F550 Flatbed Chase Truck, Dual Axle, 6.0 Engine with 212,000 Miles on it. Runs Strong, A/C.
Rotary S - SRS #4556
DESCRIPTION: 2008, Schramm; Model: T450WS; Compressor: 900/350; Engine: CAT 3406C; Mounted On: 2008 IHC 7500; Truck Engine Make: 570 HP; Condition: Working Drill - OPEN TO REASONABLE OFFERS; Tools/Options: Schramm T450WS Year: 2008: Hydraulic Welder, Oiler, New Rubber in the Back, Hendrickson Suspension, 30K Pullback, Rig is Set Up to Run 3.5" Drill Rod. New Chains in the last 2-1/2 Years, New Rollers in Mast, Mast is Straight, 3 Outriggers, 15-Rod Carousel, Bean Water Injection (rebuilt in 2024), Swinging Jib, Hydraulic Breakout Wrench, Aluminum Tool Box, No Sandline. Needs a New Sock in the Derrick. Includes 600' of good/used Drill Rod, Head Doughnuts, Complete Hose Kit for Big Compressor Hoses (1 hose used), Valve Rebuild Kit. Truck has approx. 54,000 Miles on it and Rig has approx. 7,000 Hours. Another 600' of Brand New 3.5" Drill Rod is Available for Extra Money. Truck Engine HP to be Confirmed.
Rotary G - SRS #4517
DESCRIPTION: 2023, GEFCO; Model: 30K; Compressor: 1050/350; Mud Pump: 3" Wilden; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: Cummins 565 HP; Condition: Great; Tools/Options: GEFCO 30K Year: 2023: Holds 6 Rods in the Carousel and 15 in the Rod Box. Single Rod Loader, Rod Spinner, Hammer Holder, Foremost Shock Sub. Some Warranty Left out of the 5 Year Warranty. Rod that drill can hold is included along with a used 6" QL6 Hammer and an 8" Rebuilt Hammer with 8-3/4" Hammer Bit and a 8-3/4" Roller Bit with 15' Sub, 5-7/8" Roller Bit for Cleanout, Stabilizers, Bit Breakers, Slips, Pipe Lifters, 10-12 Bags of Mud. Also Includes a Water Truck (2) 20' Hoses, No Fuel Tank on the Truck but has a 120 Gallon Tank with an Electric Pump that could be Included. Rig is Set Up to Run 4.5" X 20' X 2-7/8" Drill Pipe. Hub Odometer Currently Reads 10,977 Miles, Total Rig Hours - 2,313 and Current Compressor Hours are 1,222.
Rotary G - SRS #4393
DESCRIPTION: 2018/19, GEFCO; Model: 40K; Compressor: Sullair 1000/350; Mud Pump: Plumbed; Engine: PTO; Mounted On: 2019 Peterbilt 367 6X4; Truck Engine Make: Cummins 565 HP (recently rebuilt); Condition: Good Working Drill; Tools/Options: GEFCO 40K Year: 2019: Newly Rebuilt Engine (Injectors, Turbo, Oil Cooler), Truck Brake Compressor also Rebuilt. Rig is set up to Run 4.5" X 20' Flush Joint Drill Pipe with 2-7/8" IF Tool Joints and a Holte 350 Casing Hammer. 25K Pulldown, 40K Pullback. 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator, 25,000# Single Line Hydraulic Main Winch over the Jib. Hydraulic Rod Spinner, Modified 60" Breakout Wrench, Auxiliary Winch Mount & Hydraulics (rig has 2 winches, cable recently replaced), 3-Speed Tophead, 15 Piece Rod Box, 6-Rod Carousel, Hammer Holder. Upgraded Joysticks (5-Volt Electric Upgrade), Compressor has approx. 2,300 Hours, approx. 6,000 Total Frame Hours, < 500 Hours on the Newly Rebuilt Engine.. Truck has 22,000# Front Axle, 46,000# Rears, 18-Speed Fuller Transmission. 400' of used pipe included.. Condition: Working Drill
Water Truck - SRS #4575
DESCRIPTION: Flatwater; Model: 1,100 Gallon; Mounted On: 1990 IHC Single Axle; Truck Engine Make: Diesel; Tools/Options: Flatwater 1,100 Gallon: Single Axle Truck with a 5-Speed Transmission. Also has a GEO-Loop 50-500 Grout Pump Mounted on Deck with a 500' Hydraulic Hose Reel and a 500' Loop Reel. Grouter has a New Honda Engine. Grout pump can be sold separately.
Water Truck - SRS #4574
DESCRIPTION: Flatwater; Model: 800 Gallon; Mounted On: 1995 GMC Top Kick Single Axle; Truck Engine Make: Gas; Tools/Options: Flatwater 800 Gallon: 800 Gallon Flatwater, 17', 6,000# Liberator Crane, Also has a 1500 Gallon Plastic Tank on Top, 100 Gallon Square Fuel Tank. Single Axle Truck with Automatic Transmission with Auxiliary Hydraulic System.
Rotary H-I - SRS #4570
DESCRIPTION: 1991, Ingersoll Rand; Model: TH-60; Compressor: HR2 750/250; Engine: PTO; Mounted On: 1992 IHC Paystar 5000; Truck Engine Make: Cummins N14; Condition: PRICE REDUCED; Tools/Options: Ingersoll Rand TH-60 Year: 1991: Everything Runs and Operates as it Should. There are (2) Joints of 3.5" X 20' Drill Pipe on the Rig, Included. 3.5" Rod Carousel in the Derrick. Rod Rack on the Side. Hydraulic Table and Breakout Wrenches. 37' or 38' Mast, Main Winch, Sandline Winch, Bean Pump, Hydraulic Jib with Scope on the Derrick, (2) Front and (2) Rear Jacks, Driller and Helpers Platforms. Odometer Reads 029,185 km 18,134 Miles. Hour Meter Reads 8,181
Rotary S - SRS #4573
DESCRIPTION: 1976, Speedstar; Model: SS15; Compressor: 256S 500/250 NOT MOUNTED; Mud Pump: GD 5X6; Mounted On: CCC; Truck Engine Make: Cummins 290; Tools/Options: Speedstar SS15 Year: 1976: 8-1/2" Retractable Table, Mechanical Clutches, Mast Extension Capable of Picking up 45' Pipe. Air Compressor Condition Unknown, Current Owner Never used it. New Pro Heat Engine Heater, New 2" Little Giant Swivel, New LF Breakout Tongs. Fresh Rebuild on the Lift Cylinders, Hydraulic Pumps and Motors. Mud Pump has had New Rods, Pistons, Valves, Seats, Liners and Packings Installed. New 700' of Sandline and 500' of New 4.5" X 20' Drill Rod with 2-7/8" IF Threads, 100' Never been in the ground. New 4.5" X 3' X 2-7/8" IF Sub with new 6-1/2" PDI Bit. New Sub 5-1/2" X 3' with 7-7/8" Roller cone Bit, (1) Hoisting Plug (2-7/8" IF), New work Platform, New Clutch for Mud Pump, New Pull Down, Shaft, Pillow Block Bearings and Sprockets. 500' of Rod will fit in rod box, compressor was removed and not used due to weight.
Mud Grout Pumps - SRS #4572
DESCRIPTION: 2018, Elgin; Model: CSI-D4 Cuttings Dryer; Mounted On: 8' X 28' X 8.5" Skid; Tools/Options: Elgin CSI-D4 Cuttings Dryer Year: 2018: Elgin CSI-D4 Vertical Cuttings Dryer, Skid Mounted Solids Control Unit Designed for Oilfield Drilling Operations. Includes VFD Controlled Operation for Efficient Cuttings Drying and Fluid Recovery. Built for use in Closed Loop Mud Systems to Reduce Waste and Maximize Drilling Fluid Reuse. Ideal for Land Based Rig Setups or Stationary Environmental systems. Compact, High Capacity Unit for Oil Based and Synthetic Based Mud Applications. Electrical control System with Protective Cage and System Wiring Package. Non Explosive Proof NEMA 4X Stainless Steel VFD Cabinet. One 60 HP Yaskawa VFD VCD Drive and One 15 HP Yaskawa. One 7.5 HP A1000 PC Pump Drive, One 5 HP VFD Feed Auger Drive. HMI Touch Screen Interface, non explosion proof Wiring and Glads. 600 Gallon Dish Bottom Tank, 6" Flanged Inlet Connection, dual 3" Cam Lock Outlet Connections, 6" Flexible connection from VCD, dual Swivel Mud Gun Jet Mixers, Hinged Lid with Dual Lifting Points. Fixed Height VCD Stand, Working Deck with Walkways and Railings, Stair Case & Removeable Ladder, 110V Power Outlets. 3X3 Self Priming, Solids Handling Centrifugal Pump Package, VFD Driven Progressive Cavity Centrifuge Feed Pump Package, Removable Hopper Assembly, 24" X 24" Belt Conveyor Package.
Mud Grout Pumps - SRS #4571
DESCRIPTION: 2020, Elgin; Model: ESS-1967; Mounted On: 42' 5th Wheel Trailer; Tools/Options: Elgin ESS-1967 Year: 2020: XP Polisher Centrifuge with ESS-1967 HD2 on a Trailer. Elgin ESS-1967 HD2 XP Solids Control Centrifuge. 60V/60Hz or 380V/50Hz. Powder Coated. NEMA 4X Stainless Steel Control Panel, HMI Touch Screen Interface with (3) Yaskawa GA-800 VFD Drives. Integrated with Trailer on Vibration Isolation Pad, Integrated Controls for Centrate Pump and Screw Conveyor. Progressive Cavity Feed Pump, 460V/60Hz - 3 Phase 500 GPM, 150 kW Genset Mounted on a 45,000# 5th Wheel 42' Trailer.
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350 with Clutch; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Mercedes Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005: Rig has 4 Jacks. Includes approx. 400' of 4.5" O.D. Drill Rod, (5) Joints are older 25'ers and the rest are 20'ers in better condition, a 6" and 8" Hammer & Bits, tools, Hydraulic Wrench, Casing Driver and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles. Total Rig Hours are approx. 10,000. Compressor has a clutch and has less hours but hours are unknown. Recently Installed a New Compressor Cooler (zero hours), New Shaft & Bearings in Rotary Head, Four Rebuilt Hydraulic Pumps and one new Pump.
Rotary A-B - SRS #4568
DESCRIPTION: 2007, Atlas Copco; Model: RD20 III; Compressor: IR 1250/350; Mud Pump: FMC Triplex Mist; Engine: CAT C27; Mounted On: 5-Axle CCC; Truck Engine Make: CAT C13; Tools/Options: Atlas Copco RD20 III Year: 2007: Hydraulics are Powered by the CAT C7. 30,000# Pulldown, 120,000# Pullback Capacity, 52' Range III Tower, FMC Triplex Mist Pump Powered by a Hydraulic Motor, Downhole Lubricator, Shock Sub, Braden Utility Winches. Included the following support equipment: Bomco F-800 Triplex Mud Pump, 7,500' of 3.5" X 30' Drill Pipe, (5) 6" Drill collars, Hammers & Bits (8" SD8 Hammer & Bits, 10" SD8 Bits, 12-/14" SD8 Bits plus TCI Bits (8-3/4", 10", 12-1/4", 17-1/2"), Three Crossover Subs. 2006 IR 1170/350 Compressor & Ariel JGQ/2 Single Stage Air Booster, Mack Pipe Truck. Well Control Equipment includes a 7-1/6" BOP (5,000 psi), Annular BOP, Accumulator, Choke Manifold. Handling Tools Include a Petol Wrench and Safety Clamp. Carrier has a Single Man Cab, Eaton 8-Speed Transmission, (5) Hydraulic Leveling Jacks, Drillers Control, 17-1/2" Table, 750 HP Engine. Maintenance Performed includes - Rebuilt Engine and Hydraulic Cylinders, Replaced Batteries, Turbo, Starter, ECM, Filters and Tires, New Paint and the Clutch and Brake Lines were Repaired.
Rotary A-B - SRS #4567
DESCRIPTION: 2014, Atlas Copco; Model: TH-60 40K; Compressor: 1070/350; Mud Pump: See Below; Engine: PTO; Mounted On: 2015 Peterbilt 267; Truck Engine Make: Cummins ISX 600HP; Condition: Good - Well Maintained; Tools/Options: Atlas Copco TH-60 40K Year: 2014: Set up for Offboard Mud, Plumbed. 18,000# Main Winch, 6-Pod Carousel, Rig is set up for 4.5" Drill Rod, 25 GPM Bean Pump. Transfer Case was Rebuilt, One of the Hydraulic Pumps was Rebuilt in 2025. Approx. 7,800 Hours on the Drill and approx. 9,000 Hours on the truck. Truck has a Jake Brake and a 13-Speed Transmission. 800' of Drill Rod Available for Extra Money.
Mud Grout Pumps - SRS #4566
DESCRIPTION: Mud Puppy; Model: 170-2SC; Mud Pump: 7-1/2" X 10" Duplex; Engine: CAT 75 HP Tier 4; Mounted On: Custom Trailer; Tools/Options: Mud Puppy MP 170-2SC with a 7.5" X 10" Duplex: Mud Puppy is approx. 4 Years Old, Custom Trailer.
Water Truck - SRS #4565
DESCRIPTION: NCM; Model: DRSU 1200 Gallon; Mounted On: 1997 Ford; Truck Engine Make: CAT C12; Tools/Options: NCM DRSU 1200 Galllon Water Truck: IMT 4004i Crane (welder not included). 1,200 Gallon Bed is approx. 28 Years Old. Truck Frame has some cracks in 4 spots. Water Bed has 3 Valves, no leaks. Truck has over 1 Million Miles on it.
Rotary R - SRS #4493
DESCRIPTION: 1996, Reichdrill; Model: T-650 W II; Compressor: 1150/350; Mud Pump: None; Engine: CAT 3406B; Mounted On: 1996 Ford LT-8000; Truck Engine Make: Cummins 300 HP; Condition: Good; Tools/Options: Reichdrill T-650 W II Year: 1996: Brand New Compressor with approx. 140 Hours on it. Newer Upper and Lower Chains. 38,000# Rated Pullback Capacity, HD 160# Chains, 26,000# Down Pressure, Standard 140# Chains, Chains are about 2 years old, Spare Chain Parts Included. 34' Mast, (2) 4.5" Hydraulic Mast Raising Cylinders, Hydraulic Retractable Table, Carousel Holds 7 Rods, Hydraulic Breakout Wrench, 4-cylinder Bean Water Injection Pump, (2) Rear 36" and (1) Front 48" Leveling Jacks. New Valves on Top of Jacks, New Water Injection Control Valve. 3,000 psi Capacity Water Injection Pump Valve, Hydraulic Winch, Jib Boom, Rod Rack Capable of Holding (12) 4.5" Rods, Night Lights. Deck Engine has a New Starter and Newer Injection Pump, New Tach Installed a few Years Ago. Serviced every 200 Hours including the Funk Oil and Air Filters. Carousel and Rod Box Included but not on the Rig. Rig is set up to run 4.5" x 20' X 2 7/8 IF" Drill Pipe, Hour Meter Reads approx. 8,170. Truck has a 9-Speed Fuller Transmission,18,000# Front Axle, 46,000# Rear Axle, Hendrickson Suspension. Truck Engine has approx. 73,066 Miles on it. Includes a New, Full Set of Front and Rear Tire Chains. Rig is Operational. Includes J-Wrench, 48" Tongs, 48" Breakout Wrench, Rod Bushing, 6" and 8" Slips. Welder in Photo Not Included. Atlas 2000 Casing Hammer Available at an Extra Cost. Rod Box and Carousel Included.
Rotary D - SRS #4456
DESCRIPTION: 1986, Driltech; Model: T40K2H; Compressor: Sullair 1000/350; Engine: CAT 3406; Mounted On: CCC; Truck Engine Make: Diesel; Condition: Good Running Drill OPEN TO OFFERS; Tools/Options: Driltech T40K2H Year: 1986: OPEN TO OFFERS!! Rig is Set Up to Run 3.5" Drill Rod. M&R: One Link Removed from the Chains, Replaced the Top of the Bean Water Injection Pump and Installed a Piston Kit, New Master Links on the Chains to Tophead, Repaired Bushing Holes & New Bushings in the Tophead Plates, Replaced Detent Springs on the Feed Spool Control Handle, Rebuilt Tophead, New Bull Shaft, Bearings, Planetary Parts, Seals & O-rings. Filled with 75W-90 Full Synthetic Gear Oil, New Water Injection Hydraulic Hoses, Replaced Numerous Hoses, Welded Crack on Hydraulic Tank Outlet Port, Repaired Main Pump Seal & Shaft, Replaced Hoses in the Rear Cabinet, Full DOT, New Pressure Relief Valve, Welded up Cracks on the Mast Support Tubes, Valve Kit on Rear Valve Bank, New V-belts on the Chassis Engine, Reman on Alternator, New U-joint on the Chassis Drive Line, All Air Filters Changed, New Oil Pressure Switch on the Deck Engine, All New Oils & Coolant, Rear Rearend Rebuilt on the Chassis, New Oil in the Rear Ends, Couple of New Circuit Breakers, New Hydraulic Oil Filters and Oil, Deck and Chassis Coolant Filters, Temp Switch on the Deck Engine, New Air Dryer on the Chassis, Air (on/off) Cylinder Rebuilt, New Air Filter Cover, Checked Rod Carousel.. Condition: Good Running Drill
Auger - SRS #4564
DESCRIPTION: 2006, CME; Model: 75; Mud Pump: Gardner Denver 4-1/2" X 5"; Engine: Cummins 6BT; Mounted On: IHC 7400; Truck Engine Make: DT 466E; Tires: Rear 11R22.5 Front 385/65R22.5; Tools/Options: CME 75 Year: 2006: Rig has 15,082 Hours, 5-speed Transmission. 3-Pump Hydraulic System (tandem gear pump and one variable displacement pump dedicated to the mud pump). 25' Mast from Base Frame, has Angle Drill Spec, High Speed Head with in/out and Side to Side Slide Base, Fluted Kelly with Quick Disconnect Hydraulic Chuck (2-5/8"), 8,500# Main Winch, 3.200# Auxiliary Winch, 1,800# Auxiliary Winch and Fast Wireline Winch. 140/300# Auto Hammer. 4-1/2" Hydraulic Rod Holder and Breakout Wrench, Hydraulic Underside Slide out Auger/Casing Rack, Underwater Tank Storage, Rod Rack for 10 Rods. 2" Mud Discharge Plumbing, Under Deck 3" Suction and Freshwater Plumbing, 900 Gallon Stainless Water Tank. Truck has approx. 110,000 Miles, Allison MD 3060 Automatic, Double Frame Chassis with 20K Rears and 14K Front Axle, 20,000# Front Winch.. Condition:
Rotary S - SRS #4558
DESCRIPTION: Seismic; Model: Mud & Air Drill; Compressor: GD 680; Mud Pump: GD 5X6 (Belt Driven); Engine: PTO; Mounted On: 2007 Kenworth; Truck Engine Make: CAT (big one); Condition: Great; Tools/Options: Seismic Mud Drill. Current owner had it down to 500', Mud Drilling. Mast is longer than the standard mast, approx. 34', Mud Pump is Belt Driven and has its own Clutches (can shut off when running air compressor). Has a New Table (same as a Badger, has a Quill that can be removed). Has been Re-decked and repainted. Runs 2-7.8" O.D. Drill Rod with Mayhew Regular Thread. Odometer Reads 3,928 Miles (drilling), 46K Rears, 20K Front Axle Full Lockers, Double Frame, Pre-emission CAT Engine (big one), Spicer Gearbox (new), Pro Heat. Mud Pan Included
Auger - SRS #4557
DESCRIPTION: 2025, Mobile ; Model: B-25; Mud Pump: None; Engine: PTO; Mounted On: Raymar TRK60S Rubber Tracks; Truck Engine Make: 44 HP Kubota Turbo Diesel; Condition: Never Used; Tools/Options: Mobile B-25 Year: 2025, 4-Speed Rotary Head, 76" Single Cylinder Feed System, Auger/Tool Guide Support, Triple Hydraulic Pump, All Controls Located in Control Panel, Emergency Shut Down, 1-5/8" Hex Safety Auger Coupling, Front Mounted Auger. 140# Auto SPT Hammer, NWJ Hammer Rod Pin. 4,500# Auxiliary Hoist, 3,000# Auxiliary Hoist, 18' Mast, Shelby Tube Sampler Extruder (3" X 30") Mounted on Helper Side, Fold Down 18" X 18" Fold Down Work Table, Breakout Accessories - Single Jaw Rod Clamp & 24" Cylinder Mounted Breakout Wrench, Tool Box, 5' Rod Rack, (4) 24" Hydraulic Leveling Jacks. NWJ Thread Connection, 3-1/4" 2K Standard Auger Connection. Rubber Tracks: OAL 74.3" Long, 9" Wide Tracks. Hydraulically Powered Planetary Drive with Internal Brakes, Wireless Remote Control & Manual Controls Mounted on Carrier, 20 Gallon Fuel Tank. Never Used. Includes a 2025 2 Axle, 22' Trailer.
Rotary E-F - SRS #4548
DESCRIPTION: Failing; Model: 314C; Mud Pump: Gardner Denver 5X6; Mounted On: 1984 Ford F700; Truck Engine Make: 370 - 429 V8 Gas; Tires: Hold Air but Older; Condition: Good - Working Drill PRICE REDUCED; Tools/Options: Failing 314C: PRICE REDUCED. Includes some bits and attachments. Truck Engine has a 5-Speed Transmission, 2-Speed Rear Axles Runs & Drives. Rig has a Main Winch and it also has a Sandline Winch. Table size looks to be 3-3/4" and it runs either N3 or N4 Drill Pipe. Everything works as it is supposed to, needs a little TLC to make it perfect. Truck will need some brake work and rig will need drop pipes. Tire hold air but are old (+/- 10 years old).
Pump Hoist - SRS #4520
DESCRIPTION: 2008, Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F450 4WD; Truck Engine Make: Diesel; Condition: Working Unit; Tools/Options: Smeal 5T Year: 2008: Manual Transmission, Sandline, Remote. Bed has some rust on it. Odometer Reads 164,481. MOTIVATED SELLER
Rotary D - SRS #4552
DESCRIPTION: 2007, Driltech; Model: T25; Compressor: 1150/350; Engine: CAT C15; Mounted On: 2007 Sterling; Truck Engine Make: Mercedes; Tools/Options: Driltech T25 Year: 2007: Approx. 9,000 Original Hours, approx. 4,500 Compressor Hours. Driller & Operators Platforms, Two Rear Jacks and Two Behind the Cab, Rod Rack, Toolbox, Hammer Holder, Carousel. Includes 900' of 4.5" Drill Rod, Bits, Stabilizer. Also includes a 2,000 Gallon Sterling Water Truck with 20' Bed. Rig can be sold separately also.
Rotary D - SRS #4551
DESCRIPTION: 2007, Driltech; Model: T25; Compressor: 1050/350; Engine: CAT C15; Mounted On: 2007 Sterling; Truck Engine Make: CAT C13; Tires: New; Tools/Options: Driltech T25 Year: 2007: Truck has 52,000 Miles on it, 7,800 Total Rig Hours, 1,800 Hours on Reman CAT C15, Rebuilt Compressor, New Air Intakes, New Mesabi Cooler Package, All New Hoses (Compressor and Hydraulic), all 3 Pumps Rebuilt, New Bearings in Funk Box, New Winch Cable, Rebuilt Bean Pump, New Tool Box, Rebuilt 2 Lower Spools, Rig and Truck Painted. Many other Repairs have been done, Head was Rebuilt and Pullback Cylinder Rebuilt 18 Months ago. Includes 400' of 4.5" Drill Rod. Available for an extra cost: New Chains, Sprockets & Pins, Rebuilt Head and Water Swivel, Rebuilt Pullback cylinder.
Rotary G - SRS #4555
DESCRIPTION: 1978, Gardner Denver ; Model: 1500; Compressor: 667 2-Stage; Mud Pump: 5-1/2" X 8" FLUID END AND POWER END (2026) RECENTLY REBUILT; Mounted On: 1978 Ford L9000; Truck Engine Make: CAT 3208; Tools/Options: Gardner Denver 1500 Year: 1978: 10" Sliding Rotary Table, Manual Clutches, Triple Line Kelly and Sandline, 24; Kelly, Kelly Clutch Overhauled. Rig is set up to run 3.5" X 15' Pipe and has a 15' Rod Box, 4 Leveling Jacks (one just recently repacked 2026). Master Cylinder on Driller side has been Repacked. Power End (2026) and Fluid End recently rebuilt, Pinion Bearings in Rotary Table Replaced (2026), Truck has a 13-Speed Transmission and Engine has a New Water Pump and Belts. Will Include 735'' of 3.5" Drill Pipe, 6", 8" and 10" Stabilizers. Recently Painted.
Rotary A-B - SRS #4554
DESCRIPTION: 2008, Atlas Copco; Model: TH-60; Compressor: 900 HR.2; Mud Pump: Plumbed; Engine: PTO; Mounted On: Peterbilt Tri Drive; Truck Engine Make: 600 HP Cummins ISX; Tires: New; Condition: Spare Drill; Tools/Options: Atlas Copco TH-60 Year: 2008: New Fabco 172 Transfer Case, New Tires, Front & Rear. Completely New Fully Rebuilt Engine (2017 - Borg Warner parts) with approx. 2,600 Hours on it. New Hydraulic Cooler in 2021, Truck has approx. 10,000 Hours and < 124,500 Miles. Drill has approx. 6,200 Hours and approx. 2,470 Compressor Hour. Fleet Maintained, Service Records Available and hasn't been used in 5 years as it was a spare drill. Rod Rack is included. Rig is Plumbed for a Centerline Mud Pump. 7X10 Aluminum Centerline duplex mud pump is available for an extra cost. Rig is set up to run 3.5" Drill Pipe.
Auger - SRS #4550
DESCRIPTION: Diedrich; Model: D-120; Mud Pump: SP-50; Mounted On: 2003 ATV with Rubber Tires; Truck Engine Make: John Deere 6.8 L; Tools/Options: Diedrich D120: Rig had every option available at the time of purchase. Original Owner.
Miscellaneous - SRS #4547
DESCRIPTION: Engine: 2015 Cummins QSX15, 525 HP California Carb Compliant Engine; Mounted On: Trailer; Tools/Options: Engine odometer reads 900 hours.
Rotary E-F - SRS #4546
DESCRIPTION: 2012, Foremost; Model: DR 12/26P-60/24-900 DR24HD; Compressor: IR 900/350; Engine: PTO; Mounted On: Kenworth T800W; Truck Engine Make: Cummins ISXZ 525 HP; Tools/Options: Foremost DR 12/26P-60/24-900 Year 2012: DR 24HD, 80,000# Pullback with Upgraded 6" Cylinders and Mast Structure Reinforcement. Upgraded RC 150 High Torque, Topdrive 12,000 ft.-lbs., Auxiliary Winch with Swinging Jib, Line Oiler, 12 GPM CAT Water Injection, Drill is set up to run 4.5" reg drill rod. Lower Drive Upgraded to 1.4 Million in./lb. (originally 1 million in./lbs.) Tier 4 Engine, Jake Brake, Upgraded Cooling Package, 20K Front and 46K Rears. Torque Lower drive has been gone through and what needed rebuilt was, Tophead has also been rebuilt. New Hydraulic Pumps and Hoses, Plates in Lower Drive were Rebuilt. New Turbo on Truck Engine. $100K in recent M&R Includes 6" to 24" Jaws, Big 16" Diverter.
Pump Hoist - SRS #4544
DESCRIPTION: 1969, Smeal; Model: 10T; Engine: PTO; Mounted On: 1994 Ford F750; Truck Engine Make: Cummins 230 HP; Tools/Options: Smeal 10T Year 1969: Truck has Air Brakes & a 5-Speed. 36' Mast, 8' Layback at 36'
Rotary G - SRS #3914
DESCRIPTION: 1975, Gardner Denver; Model: 2000; Mud Pump: GD 7-1/2" X 10"; Engine: PTO; Mounted On: 4-Axle Crane Carrier; Truck Engine Make: 400 Cummins; Tools/Options: Gardner Denver 2000 Year: 1975: 58' Mast, 10" Retractable Rotary Table, Air Clutches, Two Drum Machine, No Sandline, No Rod Rack, 4-1/4" or 4-1/2" X 38' Hex Kelly (needs confirmed), Rig is set up to run 30' Rod. Has a Large Gardner Denver Swivel that has been Rebuilt, 2 Wells since. Has a Winch on the Side for Oil Field Dogs. Also Includes 810' of 5" X 30' Drill Rod with 3-1/2" IF Threads (used on 6 wells) and a Rod Trailer that was Purchased New and has < 300 Miles on it. Can be sold without rod.
Mud Grout Pumps - SRS #4541
DESCRIPTION: Mud Pump: 2023 Gardner Denver 5X6 FXG 172; Mounted On: Unmounted; Condition: Never Used; Tools/Options: Gardner Denver 5X6 FXG 172 Year: 2023 New, Never Used Gardner Denver 5X6 Mud Pump.
Water Truck - SRS #4305
DESCRIPTION: Water Truck; Mounted On: 1998 Volvo Auto Car; Truck Engine Make: CAT 3406E 475 HP; Condition: PRICE REDUCED; Tools/Options: 2,200 Gallon Tank that has been Sandblasted and Painted. 20' Bed, 200 Gallon Fuel Transfer, IMT 2020 Teathered Control Crane. Truck has an Eaton Fuller 8LL Transmission, Jake Brake, 46K Full Locking Rears. Runs Strong, Doesn't Burn Oil or Blow Smoke, Miles Unknown
Auger - SRS #4394
DESCRIPTION: 2002, Mobile; Model: B61HDX; Engine: 4BT Cummins; Mounted On: 1992 Ford F800 2WD; Truck Engine Make: Ford 7.8L 210 HP; Condition: SOLD; Tools/Options: Mobile B61HDX Year: SOLD 2002: 3L8 Moyno Water Pump, In/Out, Side to Side Wiggle Tail, Main, Auxiliary & Saf-T-Driver Winches, 3 Outrigger Jacks, 2 Swingout Auger Storage Racks. Truck has approx. 156,000 Miles on it. Tooling in Photos Included. SOLD
Mud Grout Pumps - SRS #4538
DESCRIPTION: Mud Pump: GASSO 1654C 5X8; Engine: Detroit 471; Mounted On: Skid; Condition: Rebuilt; Tools/Options: GASSO 1654C 5X8: 250 Gallon Diesel Tank. New Expendables Included but not Installed. Enclosed Chain in Box, Enclosed Chain from Engine to Pump. 5-Speed Transmission (high pressure, low fluid).
Steel - SRS #4537
DESCRIPTION: Ingersoll Rand; Tools/Options: 500' of 4.5" X 20' Ingersoll Rand Drill Rod with 3.5" Connections. T4 Hex/Squares. Calipers a full 4.5" but some Pitted from Sitting.
Steel - SRS #4535
DESCRIPTION: Ingersoll Rand; Condition: Good; Tools/Options: Ingersoll Rand: Near New Ingersoll Rand 4.5" OD X 30' Drill Rod with 2-7/8" Threads. Approx. 1,020' (34 joints) Available.
Rotary G - SRS #1967
DESCRIPTION: Gardner Denver; Model: 3000; Mud Pump: 7-1/2 X 10 GD; Engine: (2) Detroit 6V71 Rebuilt in 2019; Mounted On: 6 Axle CCC; Truck Engine Make: 871T; Condition: Excellent; Tools/Options: Gardner Denver 3000 : Operating Daily! Re-manufactured in 2006. Double Drum with Sandline - 3 Drum line (no need for rathole), Kelly Track in the Derrick. Fast Drilling, Easy Removeable Table. 60' Racking Board. 1 deck engine drives the mud pump and the other engine drives the Drawworks. 70' mast, telescopes to 97', rated @ 250,000# with 100 ton Webb traveling block with 1" cables. 4" King swivel with 4-1/2" IF X 37' fluted Kelly. 18" Brewster Skytop oilfield table. (2) BJ breakout tongs, air clutches, (6) hydraulic jacks (4) screw jacks, 50 ton McKissick block (Kelly), operators platform. 4-5 yrs. old since completely rebuilt from ground up. Includes all the standards - elevators, slips, bushings. Has set 36" Casing, Table Lifts Out with Sling. Deck Engines Rebuilt in 2019. All 4 Rear Axles Pull.
Pump Hoist - SRS #4512
DESCRIPTION: 2016, Hunke; Model: 6T; Engine: PTO; Mounted On: 2016 Ram 5500 4WD; Truck Engine Make: Cummins 6.7L; Tools/Options: Hunke 6T Year: One Owner, Sandline with approx. 1,000' of Cable, 3 Outriggers, Hunke Tilting Pipe Racks. Owner believes there is a wired remote. Truck is Equipped with Power Windows, AC and has approx.. 98K Miles. 11' Palfinger Bed, Spray in Bedline. There is Moderate Damage to Driver Side Front Corner, Swiped 6 Years Ago. The Door was modified to close securely and was used daily in it's current state.
Pump Hoist - SRS #4516
DESCRIPTION: 2024, TDH; Model: 6X2; Engine: PTO; Mounted On: 2024 Ford F600 4WD; Truck Engine Make: 6.7L Power Stroke Diesel; Condition: Working Unit; Tools/Options: TDH 6X2 Year: 2024: Two Line Machine, Remote. Power Stroke Diesel Engine, Extra Rear Springs, approx. 17,000 Miles on Truck, Subject to Change. All Aluminum Boxes, Three Leveling Jacks. Working Unit. No Mechanical Issues.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
Rotary D - SRS #4291
DESCRIPTION: 1995, Driltech; Model: T40KW3 Long Tower; Compressor: 1160/350; Mud Pump: 5-1/2" X 8" Gardner Denver; Engine: Cummins K19 600 HP; Mounted On: 1994 CCC with Lift Axle; Truck Engine Make: Cummins 350; Tires: Good; Condition: Well Maintained; Tools/Options: Driltech T40KW3 Long Tower Year: 1995: 600 HP Deck Engine, Long Tower, Hydraulically Driven Mud Pump, 20" Table Opening. 2-Speed Tophead (0-50 rpm @ 120,000 in/lb. & 0-150 rpm @ 92,000 in./lb.), 2.25" Pulldown Chains, Mast has a 34' Stroke, Inner & Outer Carousels, each Carousel holds (6) 4.5" X 25' Rods. One Exception on the outer carousel, a surface collar sits in one of the rod pods, The top of the collar is the same as the 4.5" Drill Rods so no change needed there. The Bottom has a Larger Pod that Sits above the original rod socket so it can easily be removed to facilitate a regular 4.5" rod. Heavy Duty Pulldown, Upgraded to the 70,000# Pullback and Installed 7.25 cu/in Rotation Pump, Tophead is Heavier Duty than a Standard D40K, Built with High Ambient Cooling for Engine, Hydraulic & Compressor Fluids, Rated for 130° F Conditions. 25 GPM Injection Pump. Includes 275' of 4.5" X 25' Drill Pipe with 2-7/8" IF Threads, 23' Surface Collar, Mud Pit. Can be sold without mud pump.. Condition: Well Maintained
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |