Rigs
Sold - SRS #4047
DESCRIPTION: Diedrich; Model: D-50; Engine: 4-Cylinder Deutz Diesel; Mounted On: Morooka MST 800 Tracks; Truck Engine Make: 4-Cylinder Mitsubishi Diesel; Condition: SOLD; Tools/Options: Diedrich D50 Year: Owner Believes it to be a 1991 - SOLD . Auto Hammer, 3L6 Moyno, 2 Winches, 3 Jacks. Good Tracks & Undercarriage. New Clutch Installed Recently. Hours Unknown.
Auger - SRS #3946
DESCRIPTION: Mobile; Model: B47; Mounted On: Marooka M700 Tracks; Tools/Options: Mobile B47: PRICE REDUCED! < 150 Hours on the Engine Rebuild and approx. 1,400 Hours on the Carrier. Hydraulic Cylinder Feed, 14,100# Retract Force and 10,600# Pulldown Force, Hydraulically Driven Head, Dennison M4D Hydraulic Motor, 5,500 ft.,lbs of Torque @ 365 RPM. Was used for Auger Drilling of 150' Wells and Rotary Drilling to 200'. Lateral Shift Rotary Table, FMC Bean 37 GPM @ 1,000 PSI Water Pump. Cathead.
Sold - SRS #4001
DESCRIPTION: 2008, Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F550 4X4; Truck Engine Make: Diesel 6.4L no DEF; Condition: SOLD; Tools/Options: Smeal 5T Year: 2008: SOLD Sandline, Remote, Two Rear Outriggers, Pipe Rack, Underbody Tool Box and Two on Deck. Truck has approx. 114,000 Miles on it, 5-Speed Transmission, no DEF, No Power Options, A/C and Cruise. Generator Mounted on the Truck is Negotiable. SOLD
Auger - SRS #3857
DESCRIPTION: 1972, Mobile; Model: B56; Mounted On: 1978 GMC 6500; Truck Engine Make: V8 Gas; Condition: Garage Kept; Tools/Options: Mobile B56 Year: 1972: 5' Stroke, Cathead, 2,500# Hoist, 2 Jacks. Truck has 48,000 Original Miles on it. Garage Kept, Under CDL.
Sold - SRS #3949
DESCRIPTION: 2007, GEFCO; Model: SS-135; Compressor: 300/200; Mud Pump: 5-1/2" X 8" Rebuilt; Engine: PTO; Mounted On: 2007 Tandem Axle Mack; Truck Engine Make: 405 HP; Condition: SOLD; Tools/Options: GEFCO SS-135 SOLD Year: 2007: Rig is Set Up for Mud, Air or Reverse Drilling. 24' X 4-1/4" Kelly, Four Hydraulic Leveling Jacks, 33' Mast Rated at 43,600# Capacity, Brand New 8.5" Hydraulic Rotary Table that Opens to 18", 3-Part Line, Double Drum Drawworks, Bare Drum Single Line Pull (10,900#), 30,738# Maximum Hook Load with Traveling Block at Bottom of Mast, 2" Swivel. 20,000# Working Hook Load with Block at Top of Mast. All Air Clutches Including Sand Reel, 2" Swivel, Sand Reel, 8' Hinged Driller Platform (center section is removable). All the Brackets in Boom & by Table are in but no Pully's or Gears for Pulldown. The Controls has the Spare for the Pulldown. Odometer Reads 4,471 Hours, approx. 44,435 Miles. 18K Front Axle, 46K Rears, 10-Speed Transmission, Two Fuel Tanks (60 gallon each), AC, Jake Brake, Rod Rack. Recent Upgrades Include: New Rotary Table, the Old One is Included with Rig but needs Rebuilt, New Breakout Tongs - Fits Rods up to 5.5-inches, New 20-foot Rod Rack, New Batteries and Front Tires, all other tires are 80%, New 3" Hoses and Plumbing. Truck was just serviced 11/23/21 W/DOT Inspection, Drawworks Rebuilt, Bearings, Clutches, New Brake Bands and Air Boots. New Hydraulic Filters, Mast Cylinder has new Seals, No Hydraulic or Oil Leaks, 5 ½ X 8 Gardner Denver Mud Pump Completely Rebuilt. Air Compressor in Perfect Working Condition. Most Lights on Mast are New. 3-Part Blocks, hoist Lines Cables are Good, Recently went 800' with 5.5" Drill Pipe. The Rig & Truck are in Excellent Condition, Currently Drilling. Drill can run everything from 2 7/8" to 5-1/2" Drill Pipe, Owner Believes it has a 3 ½ IF thread on Kelly now. Kelly Subs to go to 2-3/8" IF or 3-1/2" IF Threads, Bits and Old Rotary Table that can be Rebuilt Included. Drill Pipe is Available for an Extra Cost. SOLD
Rotary H-I - SRS #4043
DESCRIPTION: 2003, Ingersoll Rand; Model: T2W; Compressor: Plumbed; Mud Pump: 5-1/2" X 8" GD; Engine: PTO; Mounted On: 2003 IHC 7500 SBA 6X4; Truck Engine Make: IH 530 Diesel; Tires: Near New; Condition: OFF MARKET; Tools/Options: Ingersoll Rand T2W Year: 2003: OFF MARKET 3-Speed Hydraulic Tophead - 12,000, 8,000, 3,500 Ft.-Lb. Torque, Floating Sub, Single Tube Derrick, 12,000# Main Hoist, 4,000# Auxiliary Hoist, 2,000# Sand Reel (700' 1/4" gacc 220 fpm), Dual Hoist Controls, 3-1/2" 9-Rod Carousel, Rod Box Holds 20 Rods. Rod Spinner, Water Injection, DHD Lubricator, Auxiliary Hydraulic Couplers. Mud Pump has Hydraulic Operated Valves. Rig is plumbed for air but no air on board, would need to run auxiliary air. Truck has a 10-Speed Road Ranger Transmission. Manual Available. No Drill Pipe Available. Rig Hour Meter Reads 8,249 Hours, Truck Hours Show 9,369 Hours and 425,993 Miles. Working Drill, Hours Will Change. Engine had a Major In-Frame Overhaul Prior to 2020 at approx. 7,200 Hours. GVWR 60,000#. OFF MARKET
Cable - SRS #4042
DESCRIPTION: Hollingsworth; Mounted On: 3-Axle Off Road Trailer; Condition: Good - Operational; Tools/Options: Hollingsworth : Rig is Operational and Built Strong.
Sold - SRS #4041
DESCRIPTION: Gardner Denver; Model: T56DL9L; Engine: PTO; Mounted On: Skid; Tools/Options: Gardner Denver Cycloblower T56DL9L: 535 CFM Capacity, up to 2,000 RPM, 20 PSIG. Two Available. PTO Driven either Direct or Belt Drive. SOLD
Sold - SRS #4040
DESCRIPTION: Compressor: Ingersoll Rand 750/250; Engine: Detroit; Mounted On: Skid; Condition: SOLD; Tools/Options: Compressor: 750/250 Skid Mounted. Engine Locked Up. SOLD
Sold - SRS #4039
DESCRIPTION: 2022, Hunke; Model: 4T; Engine: PTO; Mounted On: 2019 Ford F 450 4WD; Truck Engine Make: 6.7 L Diesel; Tires: Brand New; Condition: SOLD; Tools/Options: Hunke 4T Year: 2022: Brand New Pump Hoist. 2,000# Single Line, 4,000# 2-Part Line, 6,000# 3-Part Line Capacity. Wireless Remote Controller for Mainline Winch (includes creep drive). Single Line Speed of 210 Feet/Minute. (2) 19' Pipe Racks, Total Mast Height of 46', Sandline with 700' of Cable and Free Fall (includes grease bank), Hydraulic Oil Cooler, Hoist Powered from PTO off Transmission, Work Light Package (includes 4 LED lights), Front Downrigger Jack, Electronic Throttle Control. The Truck is in Excellent Condition, has approx. 50,000 Miles on it. Truck went into Service Jan. 2020. CM, 11' Flatbed Body, Crew Cab, Power Windows, Locks, etc. Brand New Wheels & Tires. The Unit has a Clean Title and is Ready to Work. SOLD
Sold - SRS #3799
DESCRIPTION: IR; Model: 380 8" Hammer; Condition: SOLD; Tools/Options: IR 380 Year: IR 380 8" Hammer with 8" and 10" Bits. 8" Bit is New. 10" XS Casing Advancement System (used once to drill 38').. SOLD
Sold - SRS #4037
DESCRIPTION: 1988, Ingersoll Rand; Model: T3W; Compressor: 825/350; Mud Pump: 3x4 Centrifugal; Engine: Cummins; Mounted On: Paystar 5000; Truck Engine Make: Cummins; Condition: SOLD; Tools/Options: Ingersoll Rand T3W Year: 1988: Has Cummins Big Cam Engine, Engine Rebuilt 3 Years Ago in 2019 and the Air Compressor was Rebuilt 2 Years Ago in 2020. Carousel, Two Front and Two Rear Jacks, Rod box, Driller & Helper Platforms. RIG HAS BEEN SOLD
Rotary T-Z - SRS #4029
DESCRIPTION: 2004, Versa Drill; Model: V-2000; Compressor: Sullair 1250/350; Engine: PTO; Mounted On: Carrier; Truck Engine Make: CAT C16 600 HP; Tires: 90%; Condition: Working Drill; Tools/Options: Versa Drill V-2000 Year: 2004: Hydraulic Pipe Handling Arm, Has a Triplex Water Injection Pump, Auxiliary Air Port is Plumbed in, Pipe Spinner. Rebuilt Hydraulic Pumps, New Oversized Leveling Jacks, New Flow Controller for Desander Pump, New External Hydraulic Plumbing & Many New Hydraulic Hoses, Inside of the tank has sloped sides that were just installed with new clean out plumbing underneath. Power unit has a new fuel injection pump, axles have been replaced with newer model ones, brakes & Budd wheels 22.5", Two new topdrive motors, the box itself has been rebuilt, Two new hydraulic pumps and the remaining pumps have been rebuilt within the last 6 months, two new steer tires and new steering components, new windshield. Carrier has a 15-Speed Transmission. Working Daily, Minimal Oil Leaks.
Sold - SRS #4003
DESCRIPTION: 2002, Schramm; Model: T-660W; Compressor: Sullair 900/350 with Clutch; Mud Pump: None; Engine: Cummins N14; Mounted On: 2002 Navistar 2674 6X4; Truck Engine Make: Cummins; Condition: SOLD; Tools/Options: Schramm T-660W Year: 2002: SOLD Deck Engine has been Rebuilt., Compressor has a Clutch and was Rebuilt in 2020. No Carousel, Rig can Carry at least 320' (4 rods in the tower and 12 in rod box), Set up for 4.5" OD X 20' with 3.5" Reg Drill Rod, Hydraulic Jib, Floating Sub for Pipe Handling, Bean 18 GPM Water Injection & Elec. Pulse Type Hammer Oiler. Tophead Drive with Dual Low Speed, High Torque Hydraulic Motors. Mast Tilt, 28.5' of Mast Travel with Rotation Torque Limiter, Slow Feed Drill - Up Valve, 18" I.D. Retractable Table. Stand Pipe, Driller & Helper Platforms, Tool Box. 44,000# Pullback and 30,000# Pulldown, 7,600# Main Winch. Break-out Wrench, One Front and Two Rear Jacks. No Sandline. The Rig is Very Tight and the Truck is Very Strong. Truck is Equipped with a Jake Brake. Includes approx. 320' of 4.5" X 20' Drill Pipe. SOLD
Sold - SRS #3954
DESCRIPTION: Midway; Model: 13M ; Compressor: LeRoi SDS 100; Mud Pump: GD 5-1/2" X 8"; Engine: PTO; Mounted On: 1979 IHC F-2674 Series; Tires: Flotation Tires on Steering Axle, Tire Size 445/65R22.5; Condition: SOLD; Tools/Options: Midway 13M : 8-1/2" Retractable Midway Rotary Table, 5-Speed Rotary Transmission, 1500 Gardner Denver Drawworks, Bean Injection Pump, 2" Little Giant Swivel, 4 Leveling Jacks, Hydraulic Pulldown, Traveling Blocks on Kelly Line and Sand Line. Tool Box on Side of Rig, Driller and Helper Work Platforms. Includes 320' of 2-3/8" IF Slotted Drill Pipe and (1) 4" Collar. SOLD
Sold - SRS #3364
DESCRIPTION: Mobile; Model: B-53; Compressor: N/A; Mud Pump: N/A; Engine: Detroit Diesel; Mounted On: 1979 Ford F600; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Mobile B-53: Truck Runs but not Licensed for the Road. Rig Runs, was being used for Coring Work. No Slide base, Rotary Slides on a Piston to the Driller's Right, Cathead, Tag Line Hoist. Water Pump is a Little Weak and there are a few Leaks. No Tooling Included. With a pump and a little work could get it running right or could be purchased for a parts rig. SOLD
Rotary S - SRS #3400
DESCRIPTION: 1976, Speedstar; Model: SS-22; Compressor: LeRoi 256S2 445/250; Mud Pump: GD 5-1/2" X 8; Engine: PTO; Mounted On: 1976 3-Axle CCC; Truck Engine Make: Cummins; Condition: Good; Tools/Options: Speedstar SS-22 (1976): Hydraulic 10" Retractable Table, 34' Mast, 3-1/2" Fluted Kelly, 2" Little Giant Swivel, Double Drum with Sandline, Mechanical and Air Clutches, Engine Preheater. OFF MARKET, PUT BACK TO WORK
Sold - SRS #3818
DESCRIPTION: 2006, GEFCO; Model: 30K; Compressor: Sullair 1000/350 7,200 Hours Drilled with Compressor; Mud Pump: 3X4X13; Engine: PTO; Mounted On: 2006 Peterbilt 357 6X4; Truck Engine Make: CAT C15; Condition: SOLD; Tools/Options: GEFCO 30K Year: 2006: SOLD 30,000# Pullback Capacity, Hydraulically Driven Mission Magnum Centrifugal Mud Pump, 20,000# Capacity Single Line Main Winch (2-part 40,000#), 6-Rod Carousel that is set up for 4.5" X 20' Drill Pipe, Single Rod Loader, Tophead Drive Cushion Sub, FMC 18 GPM Water Injection Pump, 7 Gallon Capacity DHD Lubricator, 4 Hydraulic Leveling Outriggers, Drill Pipe Spinner. 34,000 Miles Driven,. Odometer Reads 14,346 Hours, 138,466 Miles, Hub Meter Reads 34,212. No Pipe Included. Repair List to Date - CHASSIS: Replace broken cab clearance lights, replace two missing bumper bolts, straighten radiator grill, replace broken mirror above passenger door window, change engine & PTO oil & filters, replace bad sensor in CAT C15, install truck master clutch air cylinder, truck cab fuel level gauge not working. AIR COMPRESSOR SYSTEM; replace air compressor oil cooler & re-test for proper cooling, clean & adjust air compressor regulation system, replace 0-ring in minimum pressure valve, replace receiver tank pressure relief valve, check and make repairs on air compressor shut down system, replace oil & filters. DRILL: Install carousel, replace O-rings in leaking ball valves below hydraulic tank, replace derrick rest rubber pad so feed cables won't interfere with cab lights, replace tophead pulldown cables, replace missing screws in control panel, control panel gauges not working - oil pressure, tachometer & water temperature, secure control panel rotary drive pressure gauge, replace electric fan motor on hydraulic cooler, clean mud from main downhole air lines, pneumatic actuator for downhole air valve is missing bolts, replace broken carousel lower guide clamp, straighten single rod loader lower mounting plate & replace bolts, dead end of feed cables at derrick crown need to be shortened & clamps adjusted. SOLD
Sold - SRS #3990
DESCRIPTION: 2012, GEFCO; Model: 30K; Compressor: Sullair 1000/350; Engine: PTO; Mounted On: 6X4 Peterbilt 357; Truck Engine Make: Cummins 550 HP; Condition: SOLD; Tools/Options: GEFCO 30K SOLD Year: 2012: Rig is set up to Handle 3-1/2" X 20' Flush Joint Drill Pipe with 2-3/8" IF Tool Joint. 25,000# Pulldown and 30,000# Pullback, 35' Mast with 29' Head Travel, 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator. 25,000# Single Line Hydraulic Main Winch over the Jib, Hydraulic Rod Spinner, Modified 60" Breakout Wrench Pulled by Hydraulic Cylinder. Tophead Rated at 1-120 rpm with Infinite Speed Control and 70,000 in-lbs. Torque. 24 Piece Rod Storage Rack with Slide Mounted on Driller's Side, 6-Piece Carousel, Pipe not Included. Two 100-Gallon Fuel Tanks. 22,000# Front Axle, 46,000# Rear Tandem, 18-Speed Fuller Transmission. 425/65R22.5 Front Tires, 11R22.5 Rear Tires. Odometer Reads 19,124 Miles and 8,549 Hours, Hub Meter Reads 17,260, approx. 3,528 Compressor Hours (need to confirm hour meter accuracy). Recent Work: New Front Brakes & New Air Dryer in 2021, New Sheaves, New Fuel Pump, New Turbo Solenoid, New Bearing in Gearbox and Four New Tires in 2020, Rebuilt Tophead, New Radiator Fan, New Cables, New Winch Brake, Rebuilt Compressor Driveshaft and New Cable on Top of Mast in 2019. 2022 Resealed Main Feed Cylinder, Added Gussets to Lower Cylinder Mount, Resealed Left Mast Raising Cylinder, Removed and Cleaned all Pins for Mast Raising Cylinder, Replaced Rod Centering Slip Inserts, Table Pins and Brackets, Jib Swing Cylinder Mounting Bracket, all Top Valve Bank Handle Boots & Push Buttons on Control Panel and Helper's Side Push Bottons, Compressor Discharge Temp Gauge, Receiver Tank Pressure Gauge and Changed Hydraulic Oil. No Tooling Available. SOLD
Bucket Rig - SRS #3832
DESCRIPTION: Gus Pech; Model: G38; Engine: Ford 300 6-Cylinder Gas; Mounted On: 1982 Ford F-800; Truck Engine Make: 429 V8 Gas; Tools/Options: Gus Pech G38: Truck will need New Tires. Complete with Tools, a 32" and a 22" . Cleanout Bucket with Flappers, Main Bucket has all New Shanks Welded on.
Sold - SRS #3952
DESCRIPTION: 2002, Ingersoll Rand; Model: T3W; Compressor: 900/350 HR 2; Engine: CAT 3406 465 HP; Mounted On: IHC Navistar 2674 6X4; Truck Engine Make: CAT C 10 370 HP; Condition: SOLD; Tools/Options: Ingersoll Rand T3W Year: 2002: One Owner Since New. Approx. 5,000 Hours on the Engine and Compressor, CAT Water Injection, Driller & Operator Platforms, Two Front and Two Jacks Behind the Cab, Carousel capable of (9) 3.5" X 20' Rods or (7) 4.5" X 20' Rods. Hydraulic Drawworks with Swinging Jib Boom 150 ft/min. Hoist Control, 18,000# Single Line Bare Drum Lifting Capacity, Jib Swings and Extends Hydraulically. Retractable Table with a 10-3/4" Opening, Air Operated Holding Wrench. Four motor Spur Gear Head, 2-1/2" Air Piping with 3" ID Spindle, 30,000# Pulldown, 26,500# Pullback. Spicer 10-Speed Transmission, 46,000# Rears, 20,000# Front. 100 Gallon Fuel Tank, Jake Brake, odometer Reads 25,854 Miles. Includes 300' of 4.5" X 20' Drill Pipe. SOLD
Sold - SRS #4035
DESCRIPTION: 2003, Pulstar; Model: P10; Engine: PTO; Mounted On: 2003 Ford F-550 4X4; Truck Engine Make: 6.0 L - Brand New; Tires: Good; Condition: SOLD; Tools/Options: Pulstar P10 Year: 2003: SOLD Sandline, Remote, Mast is approx. 38' (to be confirmed), Brand New Bullet Proof 6.0 L Engine and Clutch. 6-Speed Manual Transmission, Utility Bed. Truck has a Front Passthrough Box, Two front Door Compartments Connect via Passthrough Box in Service Truck. approx. < $160,000 Miles on it.
Sold - SRS #4028
DESCRIPTION: 1978, Ingersoll Rand; Model: T4; Compressor: 1050/350; Engine: Detroit 12V71; Mounted On: CCC; Truck Engine Make: Cummins 300 HP; Tires: Newer; Condition: SOLD; Tools/Options: Ingersoll Rand T4 Year: 1978 : SOLD Drill was Refurbished in 1994, Upgraded Spur Gear, 7-Rod Carousel plus 4-Rod Carousel, 16,000# Heavy Duty Winch on Mast and Jib Boom, 50K Pullback, 15 GPM Bean Injection Pump. Truck has a 13-Speed Fuller Transmission and Jake Brake. Includes 12 Joints of Drill Pipe, more Pipe available for an Extra Cost. Lots of New Parts Including but not limited to all new parts in V12 rebuild, all pumps were redone, brand new hydraulic cooler, twin turbo in deck engine. SOLD
Sold - SRS #4022
DESCRIPTION: Failing ; Model: CF-15; Compressor: LeRoi 256 SDS with Clutch; Mud Pump: Failing 5X6 Duplex; Engine: PTO; Mounted On: Ford 9000; Truck Engine Make: 8V71 Detroit; Condition: SOLD; Tools/Options: Failing CF-15: SOLD Bean 4-Cyl Injection Pump, Failing 5-1/2" Retractable Rotary Table with Air Assist, GD 2" Swivel, Failing 1500 Drawworks, Air Operated, Failing Wireline Drum with Twin Disc Clutch, (3) Leveling Jacks, Hydraulic Pulldown, Driller & Helper Work Platforms, Air Throttle. Truck has a 3TA95 Fuller Aux/PTO. SOLD
Rotary J-L - SRS #4020
DESCRIPTION: 2005, Knebel; Model: HY99; Compressor: 200 psi; Mud Pump: On Board; Engine: PTO; Mounted On: Bercedes IHD 6X6; Truck Engine Make: Mercedes V6; Condition: Very Good; Tools/Options: Knebel HY99 BRS Year: 2005: Rig is Set Up for Reverse Circulation Drilling. Very Powerful Drill that can Handle 24" Casing. Drill Can't Rotate the Casing but it has Double Clamps on the Bottom to Hold the Casing. Rig has a 25' Stroke, 40,000# Pullback, 20,000# Pulldown. Top Crane (rod handler) with 1-Ton Lift, Percussion 6,000# Lift, Swivel Head with Hydraulic Chuck and a 6" Bore, 9,588 Ft.-Lbs. @ 0-100 RPM. Rinse Pump, Automatic on Drilling Function. Double bottom clamp where the lower on can be displaced 23". Truck Engine has approx. 6,000 Hours. The Rig is Currently Set Up to run 4.5" Drill Pipe but Can be Set Up for 6" RC Pipe. Rig is Capable of Holding 600' of 4.5" Drill Rod. The Rig is Suitable for Air Raising Drilling, Direct Flush Drilling, DTH Drilling & Dry Drilling. Good for Large Diameter Water Wells. No Rod or Tooling Included. The Rig is in Good Mechanical & Hydraulic Condition, Recently Sandblasted and Painted.
Sold - SRS #4017
DESCRIPTION: Drilling Business no Real Estate; Model: Gardner Denver & Midway; Compressor: 750 and 850; Mud Pump: Unmounted; Condition: SOLD; Tools/Options: Drilling Business Started in the 1940's with Huge Customer Base, Turn-Key Operation. RIGS HAVE BEEN SOLD Two Rotary Drills: Midway 1000 with New CAT Engine & Transmission Mounted on a 1981 IHC Chassis and a Gardner Denver 1500 Mounted on a 1988 Ford LT 9000. GMC 1,800 Gallon Flat Tank Water Truck,3,200 Gallon IHC Water Truck, 4,200 Gallon Chevy Water Truck. Two Dodge Ram 3500 Dual Wheel Trucks with Tools, one is a 1997 and the other is a 2000. CAT 277 Skid Steer with Bucket & Forks, Two Atlas Copco Air Compressors, 750 & a 850. Trailer Mounted Mud Pump, 30' Tandem Dual Axle Gooseneck Flatbed, Red Gooseneck Flatbed, Dump Box Bumper Pull Trailer, Plastic Water Tanks, Diverter, (3) Bulk Fuel Tanks with Pumps, 8" Steel Casing, Drill Pipe, (4) Hammers, Grout Pump, Welders, Casing on Hand, (5) PDC Bits, 24' Flatbed Trailer.
Cable - SRS #4015
DESCRIPTION: Sasgen; Engine: Kohler 35 HP Propane; Mounted On: Skids; Condition: Good; Tools/Options: Sasgen : Cable Tool Rig for Drilling Inside of Buildings, Typically for elevator jackholes but could also be used for other types of drilling. Includes Drill Bit/Stem Assembly, Bailer, Rigging, Pulleys, Beams, Bracelets, etc.
Sold - SRS #4013
DESCRIPTION: Mounted On: 1999 Sterling Tandem Axle; Truck Engine Make: CAT Diesel; Condition: SOLD; Tools/Options: 1,500 Gallon Flatwater Fleet Flat Tank Water Bed, 300 Gallon Fuel Tank, Lights, Tool Boxes, Pintle Hitch on Rear. Heater Tubes to put the Burners in Installed for cold Climate. 3-Level Jake Brake. Truck Engine has almost 400 HP, Eaton 13-Speed Transmission with Splitter and < 130,000 Miles. Real Clean, a little Rust Staining on the Bed. No Leaks in Tank. Open Flat Deck Part is 18' Long. Welder in Photo not Included. GVW 53,000 SOLD
Sold - SRS #3909
DESCRIPTION: 2020, Semco; Model: S6000; Engine: PTO; Mounted On: Unmounted; Condition: SOLD; Tools/Options: Semco S6000 Year: SOLD 2020: Boom Capacity is 12,000# - 2-part Line, 4' Lay Back. 35' Maximum Vertical Boom Reach, 13'6" Maximum Horizontal Boom Reach. 6,000# Single Line Main Line Winch Capacity, Extended Derrick, 5T Single Line Safety Hook. 12,000# Double Line Main Winch Capacity, 8T Double Line block with Safety Hook. 140' X 7/16" XIPS Non-Rotation 19X7 Cable. 120 Ft./min. Manual Hydraulic Control. TRUCK IN PHOTOS IS NO LONGER INCLUDED
Sold - SRS #3993
DESCRIPTION: Gardner Denver; Model: 500; Mud Pump: 4-1/2" X 5" Gardner Cenver; Engine: PTO; Mounted On: Ardco Buggy; Truck Engine Make: Detroit Diesel; Condition: SOLD; Tools/Options: Gardner Denver 500: SOLD Kelly Drive Drill, 5" Gardner Denver Rotary Table, Spicer Transmission, Rockwell Transfer Case PTO. Includes a 500 Gallon Gemco Water Buggy. SOLD
Compressors - SRS #3903
DESCRIPTION: 2006, Compressor: Sullair 1350/350; Engine: CAT C-16 630 HP; Mounted On: Master Skid; Condition: TEMPORARILY OFF MARKET; Tools/Options: Electric Started, Radiator, Gauges, Heat Exchanger. Can be Turned up to 1150/500. Approx. 3,460 Hours.
Mud Grout Pumps - SRS #4011
DESCRIPTION: Mud Pump: Gardner Denver FXZ; Engine: 8V71; Mounted On: Skid; Tools/Options: GD FXZ: Air Clutch. Owner Believes it is a 7-1/2" X 12" or 7-1/2" X 14". Misc. Bits for Hammers also Available.
Compressors - SRS #4010
DESCRIPTION: Ingersoll Rand; Compressor: IR XHP 900/305; Engine: 12V71TT; Mounted On: CMI Loadking Tandem Axle Gooseneck Trailer; Tools/Options: Ingersoll Rand IR XHP 900/350: 617 Hours on Out-of-Frame Engine Rebuild. Tandem Axle Gooseneck Trailer with Fold Down Walkways on each Side. Landing Gear Installed so it can be Dollied and Leveled.
Sold - SRS #3590
DESCRIPTION: Mounted On: Ardco; Truck Engine Make: Ford 300 CID; Condition: SOLD; Tools/Options: 700 Gallon Poly Tank, Pintle Hitch, 4WD with 5-Speed New Process Transmission, Chain Drive Transfer Case, New Oil Pan, Ramsey 700 PTO Drive Winch, Belly Pan to Front Axle Housing. Some Small Leaks, has Parts to Repair, New Point. 8,200# Empty, 14,500# Filled with Clean Water. Will fit on an 8' Flatbed.. SOLD
Sold - SRS #3976
DESCRIPTION: 2000, Simco; Model: 9100; Compressor: Sullair 500/210; Mud Pump: Moyno 3L8; Engine: John Deere 8.1 L - Used to Run Compressor, approx. 2,900 Hours; Mounted On: 2000 Sterling LT9500; Truck Engine Make: CAT 3126; Condition: SOLD; Tools/Options: Simco 9100: SOLD Turnkey Tophead Drill Rig, 30,000# Pullback, 12,000# Main Hoist, 8,000# Sandline, 22' Stroke, Jib Boom, Two Front and Two Rear Jacks, 140" Auto Hammer, Pipe Spinner (not currently installed), Hydraulically Run 3L8 Moyno Pump, Bean Injection Pump, Breakout Wrench, Hydraulic Mud Mixer, Built-in Tool Boxes/Auger Racks/Rod Rack. John Deere Engine Runs the Compressor, has approx. 2,900 Hours. Truck has approx. 574,500 Miles on it, CAT Engine has approx. 13,683 Hours. Recently Serviced by CAT. Overall in Good Condition, Regular Maintenance. Recently had the Drill Head and Jib Rebuilt, New Main Line. Auto Hammer was Calibrated Summer of 2020. Current DOT Inspection. Alcoa Aluminum Wheels, 8-Speed Eaton Fuller Transmission, Exhaust Brake, Three Separate Chelsea PTO's for the Drill. . Front Toolbox Contains a Full Set of Tire Chains. Very Clean Machine Ready to Work. The Drill is Fully Set Up and Well Suited for Mineral Exploration, Geotechnical and Water Well Drilling. Includes a Full Set of Manuals and some Spare Components. Tooling Included: 400' of 6" X 20' Flush Threaded New Surface Casing, 900' of 2-3/8" X 20' IF Rotary Rod, (2) 4-1/2" X 20' Drill Collars, (1) 6" X 20' Drill Collar, (1) 8" X 20' Drill Collar, (3) 3-1/2" X 20' API Rotary Rod, (2) 3" X 4-1/2" X 20' Conventional Core Barrels One Good One Used with Bits. Diverters, Misc. Large Tricone Bits (4" to 12"), Slip Wrenches and Subs. Core Pipe Available for an Extra Cost.. Condition: Working Drill. SOLD
Sold - SRS #3950
DESCRIPTION: 1966, Failing; Model: 1250; Mud Pump: 4X6; Engine: PTO; Mounted On: 1983 IHC Single Axle Truck; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Failing 1250 Year: 1966: SOLD Quill 5-5/16" Retractable Table (can get a 6" bit through it), Mechanical Clutches, New Kelly Bar, 3-Drum Machine, has a Sandline. Truck has a 5-Speed Transmission , No Air Brakes, Not Under CDL and is Road Worthy. Drill is in Fair Condition, Needs New Cables, Drawworks are not strong. Drill has sat since 2020 but fired up recently. Truck Engine and Mud Pump Rebuilt in 2014. Includes approx. 280' of Mayhew Jr 2-3/8" Drill Pipe that was Purchased New in 2015
Rotary M - SRS #4009
DESCRIPTION: Midway; Model: 1250 Drawworks; Compressor: GD 667; Mud Pump: 5X6; Engine: PTO; Mounted On: 1991 Mack CH 600; Truck Engine Make: CH 613; Tires: New; Tools/Options: Midway 1250 Drawworks: Two Hydraulic Jacks, Spicer 500 HP Transfer Case, GD 2000 7-1/2" Stationary Rotary Table, 20' Rod Rack, Hydraulic Pulldown,, 2" Little Giant Swivel. Needs a Clutch Brake for the Truck and a Fork to Engage the Pulldown. Rig Runs Good. 2022 Went through Fluid End, Kelly Hoses, Work done to Engine.
Sold - SRS #3913
DESCRIPTION: Badger; Model: 1250; Compressor: 100 S 1 LeRoi; Mud Pump: Gardner Denver 5X6; Engine: PTO; Mounted On: 1994 Mack R-600; Truck Engine Make: E-7 Mack Diesel with Engine Brake; Tires: 11R24.5; Condition: SOLD; Tools/Options: Badger 1250: 8-1/2" Gardner Denver Rotary Table, 1250 Drawworks with Wichita Air Clutches, 2" Little Giant Swivel, 4-Speed Hydraulic Pulldown, 5-Speed Rotary Transmission, 4 Leveling Jacks, 4-Cylinder Bean Injection Pump, Driller and Helper Platforms, Breakout Tongs, Tool Boxes on both Sides of Rig. Truck has an Engine Brake, 7-Speed Maxi torque Main Transmission, 3-Speed Fuller 3TA Auxiliary Transmission, 16,000# Front Axle, 44,000# Rear Axles, Double Frame, Heavy Duty Brush Guard, Power Steering. 11R24.5 Tires, Budd Wheels. Includes 300' of Mayhew Regular Flush Joint Drill Pipe - Slotted and a 20' 3-1/2" Drill Collar. SOLD
Sold - SRS #4002
DESCRIPTION: 2007, Smeal; Model: 6T; Engine: PTO; Mounted On: 2012 Ford F-550 4X4; Truck Engine Make: V10 Gas; Condition: SOLD; Tools/Options: Smeal 6T Year: 2007 PTO; Smeal has a Sandline and Remote, Front Jack, Two Rear Jacks, Truck has a Utility Bed, Automatic Transmission, Power Windows, Locks, A/C, Cruise and approx. 108,000 Miles on it. Generator is Negotiable. SOLD
Sold - SRS #3644
DESCRIPTION: Walker Neer; Model: C25A; Engine: Cummins; Mounted On: Mack; Truck Engine Make: Mack; Condition: SOLD; Tools/Options: Walker Neer C25A: SOLD Recently Painted, Approx. 7,000' of 5/8" Swab Line, New Casing Line. Rig also has a Spudding Beam, 8X7 Twin Poles. Approx. 220,000 Miles, 1979 or 1980 Truck. Includes a Set of 2-3/8" or 4" Tools. No Tongs.
Sold - SRS #3870
DESCRIPTION: 2006, CME ; Model: 55 LC; Engine: PTO; Mounted On: Tracks; Truck Engine Make: Cummins 4BT; Condition: SOLD; Tools/Options: CME 55 LC Year: 2006: Two Auxiliary Winches, One Main Winch, Wireline Winch, Front Carrier Winch, Break-out Wrench, Rod Clamp, Moyno 3L6 Pump, Water Tank, Auger Rack, 10' Rod Storage, Slide base/Wiggle Tail. New Remote, Capable of Low Clearance Drilling, Good Tracks, Plumbed for a Cathead. Engine has close to 12K Hours. SOLD
Sold - SRS #3921
DESCRIPTION: 1978, Ingersoll Rand; Model: TH-60; Compressor: 750/250 Screw; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: 1978 Paystar; Truck Engine Make: 8V71 Detroit; Condition: SOLD; Tools/Options: Ingersoll Rand TH-60 Year: 1978 PTO; Compressor: 750/250 Screw; Mud Pump: 3X4 Centrifugal; Mounted On: 1978 IHC Paystar; TrEngine: 1978, ; Tools/Other Options: Hoist Line, Sandline Carousel. Includes 400' of Drill Pipe. Has a few hydraulic leaks. Ready to Drill. SOLD
Sold - SRS #4005
DESCRIPTION: Late 1970's, Gardner Denver; Model: 3000; Engine: Owner believes it is a Detroit 871 but not sure.; Mounted On: Trailer; Condition: SOLD; Tools/Options: Gardner Denver 3000: SOLD Single Drum, 4" Square Kelly with 3" Swivel Set Up for Direct Mud Rotary and Reverse Air, Air Clutches. Needs Some TLC, Sandblasting and Painting along with The Drawworks and Rotary Gone Through. It was Drilling a Few Years Ago but has been Sitting Since.
Sold - SRS #3896
DESCRIPTION: Water Truck; Mounted On: 2000 Ford F-750; Truck Engine Make: CAT In-Line 6-Cylinder; Condition: SOLD; Tools/Options: Allison Automatic Transmission, Two 1,000 Gallon Poly Tanks. PRICE REDUCED
Sold - SRS #3895
DESCRIPTION: Drill Steel; Condition: SOLD; Tools/Options: 1,000' of 4" Aluminum Drill Pipe with 2-7/8" IF Steel Pins & Box. 95% Life Left, 100' was used for Collars. Includes the Trailer. PRICE REDUCED !
Sold - SRS #3894
DESCRIPTION: 1978, Failing; Model: CF-15; Mud Pump: 7-1/2" X 10" Gardner Denver; Engine: PTO; Mounted On: 1978 Ford 9000; Truck Engine Make: 300 Cummins; Condition: SOLD; Tools/Options: Failing CF-15 Year: 1978: PRICE REDUCED 8-1/2" Retractable DSM Rotary Table, Manual Clutches, Double Drum Drawworks. Cummins Engine has been Rebuilt and has Low Hours since. SOLD
Rotary H-I - SRS #3530
DESCRIPTION: 1992, Plains; Model: A2000 ; Compressor: 200/300; Mud Pump: 3X5 Mission; Engine: PTO; Mounted On: 1992 GMC Topkick; Truck Engine Make: Jasper < 200 Hrs.; Condition: Working Drill; Tools/Options: Plains A2000 Year: 1992: 30,000# Pullback, No Carousel. Good for 600' Geothermal or Water Wells. 2-Speed Tophead, Two Winch Lines 8,000# and 12,000#, Pump on it is used for Grouting/Mixing, centrifugal that is hydraulically driven. New Breakout Wrench and new front drive tires. Also has (3) sets of table dies for different size pipe. Truck has a 10-Speed Transmission, Odometer Reads 490,000 Reads as it is Drilling, subject to change since it is a working drill. Drivers seat cushion is torn. Pipe Available.
Rotary A-B - SRS #4004
DESCRIPTION: Ardco; Model: C1000; Compressor: Pull Behind Sullair Available; Mud Pump: Gardner Denver 4-1/2" X 5"; Engine: 6-Cyinder John Deere; Mounted On: 1983 FWD 6X6; Truck Engine Make: 671 Detroit; Tools/Options: Ardco C1000: Mast has been Modified to use 20' Mayhew Junior API Drill Pipe. 300' in Rod Box on Truck. Has a 3" Versa Matic Air Driven Mud Pump for Grouting PVC Wells. Ditch Witch Pierce Arrow 4' Casing Hammer. Turbocharged Truck Engine has Low Miles Since Rebuild. The transfer case is currently not connected but everything is there, just needs an air over hydraulic valve to engage the front axle. Only used for 6X6. Brakes were all replaced 300 miles ago with all new drums, brake pads, brake chambers, air lines and air tanks. Truck was converted from a manual transmission to an Allison HT 740 automatic transmission. Transmission Replaced in 2019. Truck is set up as a Dual Fuel User, One 120 Gallon Aluminum Highway Fuel Tank for Truck and One 120 Gallon Off Road Aluminum Fuel Tank for Rig Motor. Hydraulics have a Triple 37 PGM Pump with 150 Gallons of Hydraulic Oil. Hydraulic Oil is in Two Tanks, The Hydraulic System has a Large Oil Cooler with Electric Fan Mounted in Front of Deck Engine. Truck is Road Worthy. Gardner Denver FFFXFM Mud Pump with Hydraulic Drive Gearbox, Fluid End on Mud Pump Could Stand to be Rebuilt. Drill has common and easy to get parts to work on it. Drill is set up for PVC wells. Tooling Included: 4" & 5" Tooling, Aluminum Cement Mix Tub approx. 400 Gallon, Drag Bits and Tricone Bits, 2" and 3" Hoses, Subs. A Pull Behind Sullair 185H Compressor is Available for an Extra Cost. It has approx. 1,764 Hours on it.
Rotary E-F - SRS #2949
DESCRIPTION: Franks; Model: 1500; Compressor: None; Mud Pump: (2) GD Mechanically Driven, (1) Centrifugal Hydraulically Driven; Engine: PTO; Mounted On: 1975 Paystar; Truck Engine Make: Cummins; Condition: OFF MARKET; Tools/Options: Franks 1500: 2 Front & 2 Rear Jacks, Kelly, Non-Retractable Table, Mechanical Clutches on Drawworks, 2-Drum Machine (drawworks & Kelly), Standard Mast. Cummins Engine was Rebuilt. Approx. 500' of 3" Drill Rod and approx. 500' of 2-3/8" Drill Rod included along with some Diamond Bits and Two Stem Trailer. Rig & Motor are Sound, Front Driveline could use a Slip Joint. OFF MARKET
Auger - SRS #4025
DESCRIPTION: Geoprobe; Model: 5400; Mounted On: 1998 Chevy 2500; Condition: Used Monthly; Tools/Options: Geoprobe 5400: Geoprobe was Serviced in 2020. New Hammer by ECT in 2017. Truck has 135,337 Miles on it, Suspension Recently Redone. Both are Running and Used Monthly.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |