Rigs
Rotary D - SRS #4291
DESCRIPTION: 1995, Driltech; Model: T40KW3 Long Tower; Compressor: 1160/350; Mud Pump: 5-1/2" X 8" Gardner Denver; Engine: Cummins K19 600 HP; Mounted On: 1994 CCC with Lift Axle; Truck Engine Make: Cummins 350; Tires: Good; Condition: Well Maintained; Tools/Options: Driltech T40KW3 Long Tower Year: 1995: 600 HP Deck Engine, Long Tower, Hydraulically Driven Mud Pump, 20" Table Opening. 2-Speed Tophead (0-50 rpm @ 120,000 in/lb. & 0-150 rpm @ 92,000 in./lb.), 2.25" Pulldown Chains, Mast has a 34' Stroke, Inner & Outer Carousels, each Carousel holds (6) 4.5" X 25' Rods. One Exception on the outer carousel, a surface collar sits in one of the rod pods, The top of the collar is the same as the 4.5" Drill Rods so no change needed there. The Bottom has a Larger Pod that Sits above the original rod socket so it can easily be removed to facilitate a regular 4.5" rod. Heavy Duty Pulldown, Upgraded to the 70,000# Pullback and Installed 7.25 cu/in Rotation Pump, Tophead is Heavier Duty than a Standard D40K, Built with High Ambient Cooling for Engine, Hydraulic & Compressor Fluids, Rated for 130° F Conditions. 25 GPM Injection Pump. Includes 275' of 4.5" X 25' Drill Pipe with 2-7/8" IF Threads, 23' Surface Collar, Mud Pit. Can be sold without mud pump.. Condition: Well Maintained
Rotary A-B - SRS #4527
DESCRIPTION: 2007, Atlas Copco; Model: T2W; Compressor: See Below; Mud Pump: None; Engine: PTO; Mounted On: IHC 7600 6X4; Truck Engine Make: CAT C13 ACERT; Tools/Options: Atlas Copco T2W Year: 2007: ex military drill. Truck has an Eaton Fuller 10-Speed Transmission, 380 HP Engine, Winch on front bumper and approx. 85,000 Miles on it. Sand Reel, Jib, Rod Box, Downhole Lubricator, Single Rod Loader. No Rod or Bits Available. Truck is extremely clean. Drill has 2500 Original Hours and was being used with an auxiliary air compressor. There is a U-Joint on the PTO to accommodate another accessory, possibly a compressor. Two Switches on the Control Panel need Replaced. At one time rig had a hydraulically driven mud pump on board.
Sold - SRS #4530
DESCRIPTION: Chicago Pneumatic; Tools/Options: 500' of CP Style Drill Rod. 3.5" O.D. X 20'.
Auger - SRS #4177
DESCRIPTION: Ardco; Model: Super L Mini Buggy; Engine: PTO; Mounted On: Ardco Buggy; Truck Engine Make: 4-Cylinder Isuzu Diesel; Tires: New; Condition: Runs Great; Tools/Options: Ardco Super L Mini Buggy: NP 4-Speed Transmission, Rockwell TRRT-32-79 Transfer Case, Bumper Mounted, PTO Driven Ramsey 400-L Winch, 3-Stage Commercial Hydraulic Pump, 14' Lockable Mast, Hydraulic Hoist Drum, Rod/Auger Rack. This Unit is Currently set up for Auger Drilling but Could be Converted to Mud Rotary with the Addition of Swivel and Mud Pump (not included). Runs Strong and is Light and Fast. Easily Hauled and Mobilized. Recently had New Tires Installed, New Radiator, New Hub along with the Hydraulic Pump being Replaced and completely Cleaned & Replaced the Hydraulic Fluid.
Sold - SRS #3899
DESCRIPTION: 1989, Mobile; Model: B47; Engine: John Deere; Mounted On: 2009 Ford F450XL Super Duty 4X4; Truck Engine Year: 6.8L; Condition: SOLD; Tools/Options: Mobile B47 Year: 1989: SOLD Two Winches, 3L6 Moyno Pump, Cathead (new rope 2021), 16' Mast, has run up to 6" auger on it, 140# Safety Hammer, approx. 170K Miles on the Truck. Truck Recently had the Engine and Transmission Replaced. Lots of Tooling Included (drive cap, adapter, 10 joints of 5' AWJ, 9 joints of 2-1/4" Auger, plug, bit, cutterhead, bit spade, hoist plug, sampler, retainer basked, sampler shoe, 3" X 30" shelby tube with caps, sample extruder assembly). Also available for an extra cost, 30' of 2.5" solid stem augers with pins and catcher that are brand new and only use some of them once or twice. Was being used for Shelby Tube Work. SOLD
Sold - SRS #4529
DESCRIPTION: Model: 3T; Engine: 4-Cyl. Wisconsin; Mounted On: 1997 Ford; Truck Engine Make: Gas; Tires: Okay; Condition: Working Unit; Tools/Options: 3T: New Hydraulic Hoses, Valve Bodies Rebuilt, New Hoist Cable, Deck Mounted Wisconsin Motor, Power Hoists. No Sandline. Truck has approx. 78,000 Miles on it. No Rust.
Mud Grout Pumps - SRS #4528
DESCRIPTION: Geo-Loop; Model: 50-500; Engine: 25 HP Honda; Mounted On: Skid; Tools/Options: Geo-Loop 50-500: Includes Hose Reel. Unit has approx. 800 hours on it.
Rotary S - SRS #4526
DESCRIPTION: Simco; Model: 2800; Mud Pump: Moyno 6L; Engine: PTO; Mounted On: 2005 Ford F550 4WD; Truck Engine Make: Powerstroke V8; Condition: Good Working Condition; Tools/Options: Simco 2800: 140# Auto Hammer, 13,500# Pullback, One Auxiliary Winch, 3 Leveling Jacks, approx. 1,783 Rig Hours. Truck Currently has 102,790 Miles on it, Toolboxes. Includes a 2003 Ford F550 Flatbed Chase Truck, Dual Axle, 6.0 Engine with 212,000 Miles on it. Runs Strong, A/C.
Water Truck - SRS #4524
DESCRIPTION: Rosewall; Model: 2,500 Gallon; Mounted On: Unmounted; Condition: Good; Tools/Options: Rosewall 2,500 Gallon Unmounted: Stainless Steel Tank/Body, Multiple Tool Boxes, Bulk Gravel Box
Parts Tooling - SRS #4523
DESCRIPTION: Atlas Copco - EPIROC; Tools/Options: Blast Hole Drilling Rig Parts, some are Used/Like New and some are Surplus/New. Owner Believes the are for a L8 Rig and DHR Series Epiroc FlexiRoc.
Mud Grout Pumps - SRS #4522
DESCRIPTION: Mud Pump: Gardner Denver 5X6; Tools/Options: Gardner Denver 5X6 Air Operated Mud Pump. Used approx. 4 Times since Rebuild.
Steel - SRS #4521
DESCRIPTION: Tools/Options: Approx. 1,200' of Ingersoll Rand 3.5" X 20' with 2-3/8" Threads, Pin Down. Used Drill Rod
Sold - SRS #4463
DESCRIPTION: 2003, Ingersoll Rand; Compressor: IR 750/175; Engine: Cummins; Mounted On: Tag Along - Pull Behind; Condition: SOLD; Tools/Options: Ingersoll Rand 750/175 Year: 2003 Cummins: 1,566 Hours. SOLD
Water Truck - SRS #4519
DESCRIPTION: Montana Flat Tank; Model: 2,000 Gallon; Mounted On: 1996 Kenworth; Truck Engine Make: CAT C12; Condition: OFF MARKET; Tools/Options: Montana Flat Tank 2,000 Gallon: 2,000 Gallon Water Bed. Super 10 Transmission, 200 Gallon Fuel Tank. Truck has 879,000 Miles on it. Grouter Not Included. OFF MARKET
Rotary G - SRS #4515
DESCRIPTION: 2020, GEFCO; Model: 40K; Compressor: 1070/350; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: Peterbilt; Truck Engine Make: Cummins ISX 605 HP; Condition: Great; Tools/Options: GEFCO 40K Year: 2020: 1,038 Hours on Compressor, 5,374 Hours on the Engine.
Rotary H-I - SRS #4518
DESCRIPTION: 1985, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Engine: PTO; Mounted On: 1988 Paystar 5000; Truck Engine Make: 8V92T Detroit; Condition: Working Drill; Tools/Options: Ingersoll Rand TH-60 Year: 1985: 13-Speed, All New Drive Lines, Transfer Box has been Rebuilt. Detroit and Air Compressor have been Replaced. Lots of New Hydraulic and Air Hoses. Machine has been Refurbished. Includes a 1996 IHC 2674 Truck with a 2,200 Gallon Water Bed, 200 Gallon Diesel Tank on Headboard, Overall Bed is 25', Rod can go under headboard, IMT Crane with Corded Remote, Powered by a N14 Cummins Engine. 8LL Transmission, 3-Stage Jake Brake, 8 New Tires on Rear. 400' of Drill Rod Available for an Extra Cost. Will Sell Drill Separate from Water Truck.
Rotary S - SRS #4514
DESCRIPTION: 2003, Schramm; Model: T555; Compressor: Sullair 1050/350; Engine: CAT C15; Mounted On: Sterling; Truck Engine Make: CAT; Tools/Options: Schramm T555 Year: 2003: Less than 2,000 Hours since Compressor Rebuild. Hours of Gauge Reads 9,653. Main Pump Recently Rebuilt (2025), 6-Rod Carousel Inside Cable Feed, Basic Rod Handling. Table Bushings & Basic Tooling Included. No Pipe Included but approx. 200' of 4.5" OD X 20' with 3.5" API Threads Available for an Extra Cost. Truck Odometer Reads 19,206 Miles. Recently Serviced (2025) - Fluids & Filters.
Rotary R - SRS #4473
DESCRIPTION: 2000, Reichdrill; Model: T-650 W II; Compressor: Sullair 900/350; Mud Pump: Wilden M16; Engine: CAT 3406; Mounted On: 2000 Freightliner 6X4; Truck Engine Make: CAT C13; Condition: PRICE REDUCED; Tools/Options: Reichdrill T-650-WII Year: 2000: 9-Pod Carousel, Set up to run 4" REICHdrill Rod, 20 GPM Bean Pump. New Chains, Sprockets, Bushings and Top Sprockets with Pillow Block and Head was Recently Rebuilt (2025), Recently Rebuilt Head (2025), CAT Deck Engine & Sullair Compressor had a Complete Factory Rebuild approx. 2,800 Hours ago with New Housing and New Radiator. Tophead Bearings Redone approx. 5,300 Hours ago. New Head Sub, New Compressor Cooler approx. 1,300 Hours ago. New Turbo and Exhaust Manifold & Gaskets also. 14' Tricone Stabilizer for 8-3/4", 500' of Drill Rod onboard, all Used Handling Tools, Slips, Bushings Included. 3rd Owner. Separate cooler still in the crate available for an extra cost.
Rotary H-I - SRS #4513
DESCRIPTION: 1981, Ingersoll Rand; Model: T4W; Compressor: Sullair 900/350 with Clutch; Engine: CAT C15; Mounted On: CCC; Truck Engine Make: Cummins 855; Tools/Options: Ingersoll Rand T4W Year: 1981: Reed R75 Mast and Topdrive, 70K Pullback. 4-Hole Funk Gearbox with Two Dennison Main Pumps, Swing and Extend Jib Boom, One Front and Two Rear Jacks, No Carousel. Compressor Clutch Adjusted in 2024 and Changed all the Fluids at the end of 2024. Includes 1,100' of 4.5" X 25' Drill Rod with 2-7/8" IF Threads and Breakout Flats on the Pin Side.
Sold - SRS #4511
DESCRIPTION: Model: 2,000 Gallon Amthor; Mounted On: 2001 Freightliner; Truck Engine Make: 500 HP CAT; Condition: SOLD; Tools/Options: 2,000 Gallon Water Bed, 200 Gallon Fuel Tank. Truck has an 8-speed Transmission. Truck Odometer Reads 769,752 Miles. SOLD
Rotary S - SRS #4014
DESCRIPTION: Speedstar; Model: SS-22; Mud Pump: GD FXO 7-1/4" X 10"; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: N 14 460 HP Cummins; Tires: Near New; Condition: Good; Tools/Options: Speedstar SS-22: Capable of Range III Casing up to 44'. 10" GD Retractable Rotary Table, Rotary Transmission with 5 Forward & 1 Reverse, Bean 4-Cylinder Injection Pump, Custom Built 56' Heavy Duty 3" Square Tubing Mast with Huge Hydraulically Folding Racking Board & Heavy Duty Substructure. Drill is Set Up to Run 30' Drill Pipe, 36' X 6" Hex Kelly with Retract, 3" Little Giant Swivel Rebuilt, PTO Rebuilt. Front & Rear Air Actuators on Driller's Panel, Main Clutch Control below Driller's Panel, Completely Rebuilt SS-22 Double Drum Brake Drawworks with LeBus Grooving, 18" Air Clutches & 3rd Sandline Drum, Hydromatic Brake, 2 Huge Traveling Blocks, Newer Hydraulic Pump, (4) Hydraulic Jacks & (2) Screw Jacks under Rotary Table Frame, Planetary Pulldown, Hydraulic Spinning Chain, Folding Drill Floor, Newer LED Lights throughout Rig. Carrier has a Fuller Road Ranger Transmission. Engine has a new PCM & Injector Pump, Rear Air over Electronic 2-Point Throttle Control, All 12 Tires are Newer, Driven approx. < 500 Miles. Includes approx. 2,100' of 3.5" X 30' Drill Pipe with 3.5" IF Tool Joints & (6) Drill Collars, Slips, Screw Plug & Bit Subs. Un-used Weight Indicator with 2 Load Cells Available for an Extra Cost (not mounted on rig). Almost Everything has been Rebuilt on this Rig from Early to Mid 2000's to Present. Heavy Duty Rig with a Big Mud Pump and Small Footprint. Needs New Ring Gear on the Fly Wheel, Will be Repaired.
Compressors - SRS #4509
DESCRIPTION: Compressor: Sullair 900/350 Air End; Tools/Options: Sullair 900/350 Compressor Air End, was working fine when removed. Owner believes it has approx. 5,000 hours on it. Two other newer ones available for an extra cost but they need some repairs and or reassembled.
Pump Hoist - SRS #4508
DESCRIPTION: 2006, Smeal; Model: 6T; Engine: PTO; Mounted On: 2006 Freightliner; Truck Engine Make: CAT C7; Tools/Options: Smeal 6T Year: 2006: Truck has approx. 150,000 Miles on it, Motor was Rebuilt within the Last Few Years. Truck GWV 25,550, Lots of Tool Boxes
Rotary G - SRS #4132
DESCRIPTION: Gardner Denver; Model: 1500; Mud Pump: 5X10; Mounted On: 1976 +/- 4-Axle CCC; Truck Engine Make: Cummins; Condition: Being Reconditioned; Tools/Options: Gardner Denver 1500: Big Kelly (4-1/2" - 5" to be confirmed), Mast is at Least 38', Rig can Handle 34' Pipe Retractable 10" Table, Leveling Jacks, Air Clutches on Drawworks, Sand Reel and Air Clutches.
Sold - SRS #4105
DESCRIPTION: 2022, Hunke (Smeal); Model: 4T; Engine: PTO; Mounted On: 2022 Ford F550 4WD; Truck Engine Make: 6.7 L Diesel; Condition: SOLD; Tools/Options: Hunke 4T Year: 2022: Hoist has a 2,000# Single, 4,000# 2-Part Line and 6,000# 3-Part Line Capability, Front Jack, Wire Winder, Wireless Remote, Hydraulic Oil Cooler, (2) Tilting Pipe Racks, Mast Lights, Hi-Low Speed for Winch, run by PTO off Transmission. Truck has a 9' Aluminum Utility Body with Flip Top Boxes with Lighting in all Boxes, Draw Assembly, Automatic Transmission, Loaded with Power Everything, Backup Camera and approx. 5,500 Miles on it and a Draw Assembly. SOLD
Mud Grout Pumps - SRS #4507
DESCRIPTION: Shop Built; Model: Grouter; Engine: 20 HP Kohler; Mounted On: 20' Tandem Trailer; Tools/Options: Shop Built Grouter Continuous Grouter: 20 HP Kohler Commander V-twin Engine with Tandem Hydraulic Unit. Dedicated Circuit for Grout Pump. 400' X 1" Reel, Moyno 2L6 Food Grade Pump capable of up to 45 GPM, currently using 1" Poly Pipe on the reel so approx. 20 GPM is more Accurate. Capable of mixing, pumping and retracting hose all at the same time. 14,000# Trailer with New Axles. Includes Ramps and Hydraulic Power Unit and Grouter can be Separated.
Sold - SRS #4295
DESCRIPTION: 1978 or 1979, Simco; Model: 5000; Compressor: Developmental; Mud Pump: 3X4X13; Engine: PTO; Mounted On: 2020 IHC Single Axle; Truck Engine Make: Cummins; Condition: SOLD; Tools/Options: Simco 5000 Year: 1979 or 1980 Simco, Manual Available. Mono Derrick, 20' Rod Rack, Single Axle Truck under CDL, Truck has approx. 105,000 Miles on it. New Planetary Pulldown for Hydraulic Motor, New Hydraulic Head Motor, Some New Hoses, Bearings Replaced, New Gauges in Console, Four Hydraulic Outriggers, Hydraulic Breakout Wrench, 6-Speed Eaton Fuller Manual Transmission. SOLD
Sold - SRS #4506
DESCRIPTION: 1998, Reichdrill; Model: T-690W; Compressor: 1050/350; Mud Pump: Plumbed - See Below; Engine: CAT 3406B; Mounted On: 1998 Mack; Truck Engine Make: Mack 350 HP; Tires: See Below; Condition: SOLD; Tools/Options: Reichdrill T-690W Year: 1998: SOLD REWORKED! Rapid Retract, 44,000# Pullback, 5" Cylinders, 140# Chains, 22" Table Opening, 6-Pod Carousel, Rebuilt Compressor (2017) approx. 1,350 Hours Since. Low Hours, Head Rebuilt in 2015, New Cooler (zero hours), New Separator Filter (10 hours), New Hercules Controls & Butterfly. 2020 New Motor for Water Injection, Deck Engine Rebuilt in 2019 approx. 1900 hours since, New Starter & Batteries, Deck Engine Battery Box Lid, Front & Left Rear Jack Pads New, Engine Heaters on both Engines. Replaced Ball Grip from A35 Control Handle, (4) Linkages on A20 Valve Bank Replaced, All Handles & Linkages on Triple Sub Plate Replaced, Water Injection 0n/off Control Replaced, Holdback Disengage Control Repaired, Holdback Pressure Gauge Replaced, Downhole Air Gauge Replaced, Rotation Gauge Replaced, Air Compressor Oil Injection Gauge Replaced, Tail Blowdown Cylinder Repacked, Tail Blowdown Cylinder Replaced, Hydraulic Tank Supercharge Gauge Replaced, Downhole Air Valve Hydraulic Cylinder Replaced, Deck Engine Hour Meter Replaced after Engine was Rebuilt. New 8 GPM Bean Water Pump, Guard over Chain Drive on Water Injection Pump, Knob on Fan Control Replaced, Barrel Loader Swing Cylinder Repacked, 3 Hydraulic Pump Replaced, Pump Gearbox Breather Replaced. Rear Clearance Light Bar on Truck Replaced. Fast Up-Pull Valve & Piston Pump Replaced. 2015 Bearing in Head was Replaced. Truck has approx. 58,000 Miles on it, an Eaton Fuller 8-speed Transmission + Low and Low/low, 3 Ranges in Reverse and 3 Ranges in Low. Jake Brake, 4.42 Rear-end Ratio. New Transmission and Clutch, New Drive Tires (8 total less than 300 miles), Steer Tires have about 3,000 Miles, New Windshield, Batteries, Driver side Seat and Power Steering Hoses have been replaced. Drill has had all Cylinders Rebuilt except for the Jacks, all Controls Rebuilt, Replaced 85% of all Hydraulic Hoses, Replaced Air Lines, Setup Filtered & Regulated Auxiliary Air off of Rig Compressor to run a Diaphragm Pump, Air Cylinder etc., Resealed Tophead. Rig can carry 260' in Rod Box and another 120' in Carousel. No Helper Controls, has a Catwalk and Platforms. Rig is Set Up to Run 4.5" Drill Pipe. 740’ of Near New 4 ½” x 20’ x 2 7/8” IF. Drill Rod Available for an Extra Cost. SOLD
Sold - SRS #4479
DESCRIPTION: 2003, Schramm; Model: 450WS; Compressor: Sullair 900/350; Engine: CAT 3406 465 HP; Mounted On: 2004 Sterling 9500; Truck Engine Make: Mercedes 410 HP; Condition: SOLD; Tools/Options: Schramm T450 WS Year: 2003: SOLD! 25' Stroke, 20 GPM Water Injection Pump, Jib, 15-Pod Carousel, 4 Outriggers, 2 Behind Cab, 2 at Rear of Rig, Braden 15,000# Winch. Rig is set up to run 3.5" OD Drill Rod. 30K Pullback, 17K Pulldown. Compressor was Rebuilt in 2017. Compressor has approx. 1800-2000 Hours Since Rebuild. Deck Engine has approx. 10,000 Hours. Doesn't use oil but has a small oil leak behind the fuel pump. Dust Collector was added in 2010. Tophead was also Recently Replaced. Has been mostly used for Geothermal Drilling with a DTH bit. Truck has a Fuller Transmission. Includes 15 Drill Rods. Last drilled Feb-March 2025.
Sold - SRS #4346
DESCRIPTION: Smeal; Model: 3T; Engine: 6.7L Diesel; Mounted On: 2018 Ford F-350 4WD; Condition: MOTIVATED TO SELL!; Tools/Options: Smeal 3T: PRICE REDUCED Mast Extends about 6', Sandline. Truck has approx. 135,000 Miles on it.
Sold - SRS #3811
DESCRIPTION: Jaswell; Model: 3500; Compressor: 900/350; Engine: 12V92; Mounted On: Paystar 5000; Condition: SOLD; Tools/Options: Jaswell 3500: 1,000' of Drill Pipe Included. A pipe Trailer is Available for an Extra Cost.. SOLD
Compressors - SRS #4504
DESCRIPTION: 1993, Ingersoll Rand; Compressor: 900/350; Condition: Working when Removed; Tools/Options: Ingersoll Rand Year: 1993: Was Removed from a 1993 Ingersoll Rand Drilling Rig. Approx. 16,000 Hours.
Compressors - SRS #4503
DESCRIPTION: 2006, Atlas Copco; Compressor: 1070/350; Condition: Was Working When Removed; Tools/Options: Atlas Copco Year: 2006: Compressor was removed from a 2006 Atlas Copco drill. Approx. 9,500 hours.
Rotary G - SRS #4502
DESCRIPTION: 1982, Gardner Denver; Model: 2000; Mud Pump: Gardner Denver 7-1/2" X 10"; Mounted On: Trailer; Condition: Refurbished; Tools/Options: Gardner Denver 2000 Year: 1982: Everything Repacked and Serviced, Drill has been Refurbished.
Rotary A-B - SRS #4501
DESCRIPTION: Turnkey Water Well Drilling/Well Treatment Install/Service Business, Condition: Operating Business; Tools/Options: Profitable, Turnkey Water Well Drilling and Water Well Treatment System Service/Install Business for Sale. Years in Business with Existing Customers in both the Water Well Drilling Side and Water Well Treatment Systems. Includes Business Name, Phone Number, Customer List and Equipment. Equipment in Excellent Condition. Including but not Limited to Drilling Rig, Water Truck, Service Trucks, Skid Steer, Inventory. More information Available to Serious & Qualified Buyers.
Compressors - SRS #4500
DESCRIPTION: 2006, Atlas Copco; Model: XAS756; Compressor: 750/100; Engine: CAT; Mounted On: Tag Along Pull Behind; Condition: Runs and Works Well; Tools/Options: Atlas Copco XAS 750 Year: 2006: Hour Meter Shows 6,252Hours. Runs and Works Well, Small Oil Leak at the Rear. Recently Gone Through by CAT Dealer.
Rotary H-I - SRS #4499
DESCRIPTION: Ingersoll Rand; Model: TH-60; Compressor: See Below; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2001 IHC; Truck Engine Make: 475 HP; Tires: New Steer Tires; Tools/Options: Ingersoll Rand TH-60: Everything on Drill is Direct Hydraulic. Mud Pump has a newly rebuilt gear end, No Air Compressor but Equipped with a High Volume Air Attachment, Rod Box. Rig has 30' of Travel on the Derrick, Extendable Jib, Sandline, Hydraulic Tongs for Breakout, Carousel has been Removed. Top Drive Equipped with a $30K Shock Sub. Recently Purchased 620' of New Heavy Drill Rod (363#/rod) 3.5" X 20' with 2-3/8" IF Thread, 2 X 5' Stabilizer one is for 7-7/8" Bit the other is for 5-1/4" Bit. 5' Stabilizers make the beginning of the first drill rod at ground level. Along with the Stabilizers includes New Button Bits (7-7/8" & 5-1/4"). Pipe Spinner Attachments have not been Removed. Truck has a 18-Speed Transmission. Drill has been gone through from front to back by a rig mechanic.
Rotary E-F - SRS #4498
DESCRIPTION: 2003, Foremost DR12; Mounted On: Sterling LT; Tires: Newer; Tools/Options: Foremost DR12 Year: 2003: New Cushman Box and Old Box has Been Rebuilt and on hand. Drill has 7,607 Hours, Truck has 20,863 Hours. Includes a 1994 Ford Crane/Service Truck with 90,094 Miles, 1979 Driltech D40K mounted on a 2005 Kenworth with 21,804 Miles, 1997 Volvo Service Truck with 230,419 Miles, includes misc. tools, 2007 Chevy Silverado K2500HD Crew Truck with 210,000 Miles, 2013 Chevy Silverado K2500HD Crew Truck with 113,258 Miles. Misc Tools & Drive Shoes included with the D40K. Extra Jaws for 8", 10" and 12", Extra Diverters for 8", 10" and 12". Oil and Filter changes are all documented. A New Sandline has been Installed on the DR12 along with a New Dashboard. All M&R Records are on File. TOTAL TURNKEY PACKAGE ALSOAVAILABLE AND INCLUDES: 2004 Flatbed Trailer (pipe hauler), Forklift, 100' of 10" Pipe, 2,280' of 5" Pipe, 12,760' of 6" Pipe, 380' of 8" Pipe, z92) Bunks & 320' of 4" Plastic, 6" DK Drive Shoes, 6" DR Drive Shoes, 8" DR Drive Shoes, 10" DR Drive Shoes, 12" DR Drive Shoes, 3,380' of 4.5" Drill Rod, 2 Pallets Bentonite Med, 2 Pallets #8 Bentonite, Land & Building (lease or purchase) along with name, customer list, phone, goodwill, non-compete.
Rotary D - SRS #4496
DESCRIPTION: 1979, Driltech; Model: D40K; Compressor: 750/300 (rebuilt in 2024); Engine: CAT 3406; Mounted On: 2005 Kenworth; Truck Engine Make: CAT C15 475 HP; Condition: Tooled up, Working Drill; Tools/Options: Driltech D40K Year: 1979: Rebuilt in 2016, Owner believes the Compressor was Rebuilt in 2024. No Carousel, 40K Pullback 26,500 Pulldown, set up to run an Atlas 2000 Casing Hammer which is Included, runs 4.5" O.D. X 20' Drill Rod. Truck has approx. 21,800 Miles and an 18-Speed Road Ranger Eaton Transmission. Includes a Tooled up 1997 Volvo Service Truck with approx. 231K Miles, approx. 200' of Used Drill Rod and (4) New Drive Shoes. Maintenance Records Available upon Request.
Sold - SRS #4480
DESCRIPTION: Geo-Loop; Model: 50-500; Engine: Honda; Mounted On: Skid; Condition: SOLD; Tools/Options: Geo-Loop 50-500: Includes Hose Reel. SOLD
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005 Diesel; Compressor: 1050/350; Mud Pump: None; Mounted On: Sterling; TrEngine: , Diesel; Tools/Other Options: Includes Drill Rod, Tooling, 8" Hammer and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles.
Pump Hoist - SRS #4494
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F350 4WD; Truck Engine Make: Gas V10; Tools/Options: Smeal 5T: No Remote but has a Plug for one. No Sandline. Hoist has a little rust on it. Drives Good.
Truck - SRS #4475
DESCRIPTION: Mounted On: 2009 Peterbilt 365; Truck Engine Make: CAT C13 Acert; Tools/Options: 15-Speed Transmission, 4:11 Gears, 3 Axle. Odometer Currently Reads 29,765 Miles and 2,819 Hours. Was used to Pull a Lowbed Trailer. 3 Trucks Available. Two with Day Cabs and one with a Small Sleeper Cab.
Steel - SRS #4492
DESCRIPTION: Condition: Never Used; Tools/Options: 19 Joints on New, Never Used 3.5" O.D. X 20' Drill Pipe with 2-3/8" Threads. Also Available 40' X 6" Used Drill Collars and Subs for the Drill Pipe
Sold - SRS #4467
DESCRIPTION: Bucyrus Erie; Model: 22W Series II; Mounted On: Trailer; Condition: SOLD; Tools/Options: Bcyrus Erie 22W Series II: Some Tools Included. SOLD
Rotary H-I - SRS #4466
DESCRIPTION: Ingersoll Rand; Model: TH-55; Mud Pump: 4X3 Centrifugal; Engine: PTO; Mounted On: 1997 Ford; Truck Engine Make: CAT 3306; Tires: Good; Condition: Good - PRICE REDUCED!; Tools/Options: Ingersoll Rand TH-55: PRICE REDUCED! Driller & Operator Platforms, One Front and 2 Rear Jacks, Cable Pulldown, Rod Box Includes 640' of 3.5" Drill Rod, 15' Collars, Various Roller Bits and Drag Bits, 5" & 6" Air Hammers with Various Bits. Working Condition, All Controls & Drawworks are Functional. Machine has Minor Hydraulic Leaks but Overall Good Shape.
Rotary D - SRS #4349
DESCRIPTION: 1977, Driltech; Model: D40K; Compressor: 750/350; Mud Pump: GD 5X6 Air Driven; Engine: 3406C; Mounted On: CCC; Truck Engine Make: 350 Cummins; Tires: Good; Condition: Ready to Work; Tools/Options: Driltech D40K Year: 1977: Fresh Paint, Dual Carousels, Set up to Run 25' Drill Pipe, Approx 600 Hours on Deck Engine. Stacker Valves Replaced. Includes 300' of Drill Pipe and Breakout tools. Not Sure of Compressor or Carrier Engine Hours. Maintenance Records Available.
Rotary S - SRS #4491
DESCRIPTION: 1982, Schramm; Model: 685 DH; Compressor: See Below; Mounted On: GMC; Tools/Options: Schramm 685 DH Year: 1982: Last used in approx. 2024. Compressor wasn't used at that time, auxiliary air was used. On board compressor wasn't working, owner thinks it has a bad bearing. Compressor is a 1000/350 - to be confirmed. Parts Rigs, Boosters, Auxiliary Air Compressor and approx. 1,200' of 25' Pipe Available.
Sold - SRS #4264
DESCRIPTION: 2014, Atlas Copco; Model: T3W; Compressor: 1070/350; Engine: PTO; Mounted On: IHC Navistar; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Atlas Copco T3W Year: 2014: Currently has approx. 3,800 Rig Hours and approx. <3,000 Compressor Hours, 40K Pullback, <18,665 Miles. Working Drill so Hours will Change. Bean Water Injection Lubricator, Single Rod Loader, Rod Spinner. Includes approx. 500' of 4.5" Rod with 2-7/8" IF Threads so a Murphy Plug can be used. Also Includes Basic Operating Tools, no Hammers. Serviced and repaired by an Epiroc Mechanic since New. SOLD
Sold - SRS #3802
DESCRIPTION: Canterra; Model: CT-350; Engine: PTO; Mounted On: 1989 Ford F-700; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Canterra CT-350: SOLD Rod Rack and Plumbing for Rotary Option, Brand New Hydraulic System Installed in Early 2019 (only drilled 6 wells since). Main Line and Sand Line with Free Fall and Spudder Option (used to drive wells in). Longer, One Piece Mast, Lot of Torque., Auger Rack on Driver's Side, Rod Rack and Tool Box on Passenger Side. 5-Speed Transmission with 2-Speed Rear. SOLD
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |