Rigs
Sold - SRS #4256
DESCRIPTION: 2007, Atlas Copco; Model: T3W; Compressor: 1070/350; Mounted On: IHC; Truck Engine Make: Diesel; Tools/Options: Recently gone through and painted in 2018. Includes Rod, Two Hammers and tooling. Deck Engine has < 2,000 Hours.
Mud Grout Pumps - SRS #4253
DESCRIPTION: Mud Pump: Gardner Denver PZ8; Engine: CAT C15; Mounted On: Skid; Tools/Options: Gardner Denver PZ8: Engine and Pump were New when Built in 2012. Allison 6061 Transmission was a New Reman when Built. Pump has approx. 2,500 Hours on it. CAT Hour Meter Reads 2,354 Hours. Pump is Fully Enclosed and has Removeable Sides. Spare Parts Available.
Sold - SRS #4225
DESCRIPTION: Simco; Model: 2800; Mud Pump: Moyno 3L6 Progressive Cavity; Engine: V 4-Cylinder Wisc. Gas; Mounted On: Ardco ATV; Truck Engine Make: 4-Cylinder Deutz Diesel; Condition: SOLD; Tools/Options: Simco 2800: SOLD Water Well & Geothermal/Environmental Drilling Capabilities. Deck Engine has Very Low Hours, Runs Great. Buggy engine is air cooled and also has low hours. All Hydraulic Tophead Drive. Tophead Auger/Mud/Air Rotary, 11' Stroke Mast with Telescoping Extension (12K Pulldown & Pullback). Extension allows for 20' Casing Handling, Hydraulic 4,500# Main Winch, Progressive Cavity Mud Pump, Top Feed Water Swivel/Plumbing 1JW, Bolt up 1-5/8" Male Hex Adaptor, Tophead off Hole Swing Out, Aux. Hydraulics for Cathead or Auto Hammer Hookups, Hydraulics Plumbed for Breakout Wrench, Rear Stabilizers, Tool Boxes, Auger/Drill Rod Racks, Driller Platform. Capabilities may vary depending on conditions, tooling weight and bore hole diameter. SOLD
Sold - SRS #4187
DESCRIPTION: 2003, DeepRock; Model: DR 150; Mud Pump: 5X6 Piston; Engine: PTO; Mounted On: 2003 Ford F-750 4WD; Truck Engine Make: Cummins 24 Valve; Condition: SOLD; Tools/Options: Deeprock DR 150 Year: 2003: SOLD 4 Hydraulic Leveling Jacks, Hydraulics are Plumbed for Mud-Slayer Guzzler or Similar with Quick Disconnects. Downhole Oiler, 2 Piston Water Injection, Extendable Mast to Set 20' Casing, 11' Stroke on Mast, Hydraulic Break-Out Wrench, Hydraulic Winch, 6,000# Winch. Truck has a 2" Receiver Hitch for Pulling Mud Unit or Compressor and an Eaton 6-Speed Transmission, Odometer Reads 140,761 Miles (increases while drilling & driving), Truck has Air Brakes. Tach on drill went bad and was changed in 2023, it had 3,410 Hours at the time it was changed, new tach reads 30.1 Not verified with computer but seems correct. Includes 5" Casing Elevator Set, 250' (25 Joints) of Used 2-3/8" IF & 3.5" X 10' Drill Rod & a Used 9-7/8" PDC 4-blade Bit and a 5-7/8" PDC 5-Blade Bit. SOLD
Sold - SRS #4190
DESCRIPTION: Late 70's with upgrades, Quickdrill; Model: 275 ; Compressor: LeRoi Developmental; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2020 Hino 268 2WD; Truck Engine Make: Diesel JO8E V8; Condition: SOLD; Tools/Options: Quickdrill 275: SOLD Late 70's Quickdrill that has been Upgraded to the Drillmax Control Panel. Single Rod Loader, Capable of Running 20' Pipe, Rod Rack, Four Hydraulic Jacks. Truck has a 260 HP Turbo Diesel Engine, Allison Automatic Transmission with PTO that Operates Rig, Odometer Currently Reads 6,567 Miles. Drill had been in an accident and mast was bent but it has since been straightened out. Will have a Rebuilt Title. Includes 500' of Mayhew Jr Drill Rod. 2007 Hino Water Truck with 1,500 Gallon Stainless Steel Water Tank Available for an Extra Cost. SOLD
Sold - SRS #4142
DESCRIPTION: 1978, Chicago Pneumatic; Model: T-650 WS; Compressor: 900/350 Sullair; Engine: CAT C15; Mounted On: Mack; Condition: SOLD; Tools/Options: Chicago Pneumatic T 650WS Year: 1978: SOLD Deep Hole Package, 50K Pullback. Includes 300' of Drill Rod and Hand Tools. Newer Main Pump and Upper Diamond 160 Chains in 2022. Drill Runs Good. Carousel has been removed but is included. SOLD
Sold - SRS #4206
DESCRIPTION: 2004, Pulstar; Model: P10; Engine: PTO; Mounted On: 2004 Ford F-550 4WD; Truck Engine Make: 6.0 L; Condition: SOLD; Tools/Options: Pulstar P10: No Sandline, 37' Telescopic Mast Good Condition, No Known Issues. Truck Odometer Reads 97,398 Miles. 6-Speed Manual Transmission. SOLD
Sold - SRS #4255
DESCRIPTION: 2007, Driltech; Model: T25KW; Compressor: 1000/350; Engine: Cummins KTA19; Mounted On: Sterling; Truck Engine Make: CAT C12; Tires: Newer Tires & Wheels; Condition: SOLD; Tools/Options: Drilltech T25KW Year: 2007: SOLD 750 HP Dual Turbo Deck Engine. Water Injection. Includes 400' of Drill Rod. Currently Set Up to Run 4.5" Drill Rod. Hour Meter not working. Compressor at some point was either rebuilt or replaced. Recent work done to the truck: Replaced 3 brake cans, adjusted brakes, replaced torsion bar, repaired air leaks, repaired some cables on the starter, and replaced all the lights. Recent work done to the Rig: Removed and dismantled the head. It was in nice shape so they put it back together and replaced the seals and packing. Replaced many leaking/frayed hoses, rebuilt valve handles, adjusted and repaired the winch jib. Replaced some gauges. The K19 runs great and starts immediately. Air compressor works well. It could go to work as is. SOLD
Sold - SRS #3557
DESCRIPTION: Mobile; Model: B80; Engine: 4-Cylinder Deutz; Mounted On: Chevy Kodiak; Truck Engine Make: 3208 CAT; Condition: SOLD; Tools/Options: Mobile B80: Four Leveling Jacks, 3-Cylinder Bean Pump, Winch Line, Wire Line, Sliding Tophead, 8-Speed Transmission. 15' of Travel, has an Extended Mast that can Handle 25' Pipe. Truck has a 10-Speed Transmission. Available: 100' plus of 4" Augers, 500' BX Wireline, NQ Barrel, 130' of N Rods. Last time it was on a job was approx. late 2018. SOLD
Sold - SRS #4031
DESCRIPTION: 1989, Smeal; Model: 6T; Engine: PTO; Mounted On: 2011 Dodge Ram 5500 HD 4WD; Condition: SOLD; Tools/Options: Smeal 6T Year: 1989: Standard Hoist, Remote, No Sandline, 6-Speed, Utility Bed, Font Jack. Truck has a Standard Transmission and approx. 206,000 Miles on it. Lift Cylinders and Jack Cylinders Rebuilt in 2022. SOLD
Parts Tooling - SRS #4245
DESCRIPTION: Tools/Options: 24" and 36" Buckets. Was used on a Texoma Rig.
Sold - SRS #4174
DESCRIPTION: 2007, Gus Pech; Model: GP-900XHR; Compressor: Sullair 700/200; Mud Pump: 7X10 Duplex Centerline; Engine: PTO; Mounted On: 2007 Sterling 6X4 L9500; Truck Engine Make: 450 HP Mercedes; Condition: SOLD; Tools/Options: Gus Pech GP-900XHR Year: 2007: SOLD Total Truck & Rig Hours are 12,207 (no hour meter on rig), Drill was Overhauled 1,811 Hours Ago in 2017. Mud Pump Rated at 300 GPM. Water Injection Pump, Standard Power Head Rated at 9,000# of Torque and 200 RPM, 26' Stroke and at least 30' of Head Clearance (slides to the left or over the drill). 8" Second Trough for Drill Collar. 40,000# Pullback and 26,000# Pulldown, 18,000# Main Winch, 4.000# Sandline. Truck has 20,000# Front Axle and 46,000# Rears. Recently had a New Rebuilt Swivel Installed, New Starter and Batteries, New Main Winch Line, New 31/2 Saver Sub. No Pipe or Tooling Available.
Sold - SRS #4242
DESCRIPTION: 1977, Schramm; Model: T 64; Compressor: 425/250; Mud Pump: Plumbed, Pump Removed; Engine: Detroit; Mounted On: 1977 GMC; Truck Engine Make: Gas; Condition: SOLD; Tools/Options: Schramm T 64 Year: 1977: SOLD Carousel, Rod Box. Mud Pump that was on it was a 5X6, Removed, Odometer Currently Reads 63,913 Miles, Working Drill, Subject to Change. New Gasket on the Oil Cooler, All New Antifreeze in the Rear Engine, Hydraulic Filter and Two Pumps Replaced in 2022, Starter was also Rebuilt in 2022 along with New Batteries (both hooked up together), New Drive Shaft behind the Second Transmission with Yolks and U-Joints (driveline checked annually), Master Clutch in 2021, Winch Rebuilt in 2020, all New Hydraulic Valves in 2019 with Pumps too, Detroit was Rebuilt about 5 Years ago (2018) and Radiator was Recored and Flushed at the same time, Air Compressor in 2000. Compressor Oil Recently changed (2023), done Once Per Year along with Rig Oil and Tophead Oil. Also Check Transmissions and Rear Ends Yearly, all of this was done in the fall of 2022. Includes Approx. 540' of Drill Rod that is in good condition, Bushings, Tooling, Two New Hammers (5" and 6"), Three New Bits (5", 6" and 8"). 1995 White GMC Truck with 1,100 Gallons of Water Storage Capacity.
Mud Grout Pumps - SRS #4241
DESCRIPTION: Mud Cleaning System; Mounted On: Skids; Tools/Options: 120 bbl. Mud Cleaning System. 120 bbl. Shaker with Two Screens, 150 kW Generator Power, Desander Cones, Mixing Hopper, 140 bbl. Chemical Tank, Deck for Chemicals, Stairs, Jib Crane. Some New Extra Screens Included. New Pick up pump can be purchased for extra money.
Sold - SRS #4240
DESCRIPTION: Mounted On: 1981 IHC 2554 Tandem Axle; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: 2,400 Gallon X 20' Flatwater Fleet Water Bed, 1993 Tiger 11' to 18' Extendable Crane (model LO54-BEH). Tandem Axle Truck with a 13-Speed Transmission and Air Brakes. SOLD
Sold - SRS #4141
DESCRIPTION: Mounted On: 1995 Kenworth T-800; Truck Engine Make: Cummins N14; Tools/Options: 2,400 Gallon Water Tank, Freshly Sandblasted and Painted. No Leaks. Tank has a 12" pipe through the center for burning wood to keep water warm, smoke stack at the top. Tank also has a 4" spot to drop a submersible pump down from top to keep people in water until you get there to drill. Truck has 800K Miles on it. Good Truck, Fires Every Time.
Sold - SRS #4238
DESCRIPTION: 1985, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Engine: PTO; Mounted On: GMC; Truck Engine Make: 8V Silver 92 Detroit; Condition: SOLD; Tools/Options: Ingersoll Rand TH-60 Year: 1985: No Sandline, Rig is Set Up to run 4.5" X 20' Drill Rod with 2-7/8" IF Tool Joints. New Compressor Cooler, New Truck Compressor, Installed Air Dryer, Installed Rotation Torque Limit Valve, Rebuilt Water Pump Top and Bottom, New Winch Cable, New Air Tank for Truck, Converted Air to Electric Truck Wipers, New Air Lines to Control Panel, New Hydraulic Lines on Head.. SOLD
Sold - SRS #4214
DESCRIPTION: 2003, Schramm; Model: T450WS; Compressor: 900/350 with Clutch; Mud Pump: Centrifugal; Engine: CAT 3406 B; Mounted On: IHC 7400; Truck Engine Make: DT 530; Condition: SOLD; Tools/Options: Schramm T450WS Year: 2003: Rig has the Extended Mast (same stroke as standard Schramm) to run an Atlas R2000 Casing Hammer (included). Rig Hour Meter Reads 9,200 but is not Working anymore. Rod Box, 8-Pod Carousel, Rig is set up to Run 4.5" OD Drill Rod with 3.5" Regular Thread, No Sandline, Two Winches, Standard 6,000# Winch and a Pullmaster 12,000# Winch, Operators Platforms, Front & Rear Jacks. Truck Odometer Currently Reads 59,600 Miles, 8LL Roadranger Transmission. Compressor Hours Unknown. Includes 400' of Drill Rod and a Used 6" Mincon Hammer, More Rod Available for an Extra Cost. Current Owner has never used the mud pump. Within the last Year or so a new 25 GPM Injection Pump was Installed, New Plates at the Bottom of the Carousel and a New Actuator Motor on the Top of the Carousel. SOLD
Sold - SRS #4233
DESCRIPTION: 2008, Foremost; Model: DR-24; Compressor: IR 900/350; Mounted On: 2008 Kenworth T-800; Truck Engine Make: Cummins ISX 525 HP; Condition: SOLD; Tools/Options: Foremost DR-24 Year: 2008: SOLD RC 110 Topdrive, 2-Speed 9,666 ft./lbs. Torque, 24" HD Lower Drive, Gear Drive 208,334 ft/lbs. Torque, 10" Discharge Swivel, Breakout & Holdback Wrenches, 6,000# Capacity Auxiliary Winch, Hoisting Cable Assembly with Quick Trip Attachment, Saver Sub, DTH Hammer Oiler, 20 GPM Bean Water Injection System, Sandline Winch, Pullmaster M8B c/w 800' of 5/16" Cable, (3) Casing Jaws, New 3" Thick Material. Approx. 14,000 Hours on the Truck and 12,000 Rig Hours and 3,450 Compressor Hours. Truck has Jake Brake, AC and Stereo9. Upgraded Cooling Package, 1,780 Square Inch Radiator, 20,000# Front and 58,000# Rear Axles. SOLD
Rotary M - SRS #4237
DESCRIPTION: Mayhew; Model: 1000; Compressor: Curtis 950/250 2-Stage; Mud Pump: Wheatley 6X6 Duplex; Engine: PTO; Mounted On: 1977 IHC; Truck Engine Make: Diesel; Condition: Working Drill; Tools/Options: Mayhew 1000 Year: 1977: Hour Meter Reads 5083.5, can not guarantee accuracy. 224,473 Miles. 2022 Rebuilt Down Feed Pump and all New Clutches and U-joints.
Sold - SRS #4235
DESCRIPTION: Mud Pump: 5X6; Mounted On: Unmounted; Condition: SOLD; Tools/Options: Air Driven 5X6 Mud Pump. Recently Rebuilt, not used since. SOLD
Sold - SRS #4232
DESCRIPTION: 1970, CME; Model: 55; Engine: John Deere; Mounted On: 2002 Ford F650; Truck Engine Make: IHC Navistar; Tires: Good; Condition: SOLD; Tools/Options: CME 55 Year: 1997: SOLD. 3 Winch Lines, Auto Hammer and Breakout Table. No Moyno Pump, Extruder, Cathead or Tooling. Truck has 77,829 Miles on it and an Automatic Transmission. No CDL Required.
Auger - SRS #4231
DESCRIPTION: 1971, CME; Model: 55; Engine: Ford 300; Mounted On: 2002 GMC 6500; Truck Engine Make: GMC Duramax - Needs a New Engine; Tires: Good; Condition: Fair; Tools/Options: CME 55 Year: 1971: PRICE REDUCED. Chassis Needs a New Engine. No Tooling Included, 3 Winch Lines, Auto Hammer. No Moyno Pump, Extruder, Breakout Table, Cathead or Tooling. Truck has 101,152 Miles on it and Manual Transmission. No CDL Required.
Sold - SRS #4230
DESCRIPTION: 1989, CME; Model: 55; Engine: Ford 300; Mounted On: 2006 IHC 4700; Truck Engine Make: IHC Navistar; Tires: Good; Condition: SOLD; Tools/Options: CME 55 Year: 1989: SOLD Options: 3 Winch Lines, Auto Hammer and Breakout Table. No Moyno Pump, Extruder, Cathead or Tooling. Truck has 227,337 Miles and an Automatic Transmission. No CDL Required.
Sold - SRS #4229
DESCRIPTION: 1988, CME; Model: 55; Engine: Ford 300; Mounted On: 2004 IHC 4000; Truck Engine Make: IHC Navistar; Tires: Good; Condition: SOLD; Tools/Options: CME 55 Year: 1988: SOLD No tooling Included, has 3 Winch Lines and an Auto Hammer. No Moyno, Pump Extruder, Cathead or Breakout Table. Truck has 89,657 Miles on it. CDL Required
Sold - SRS #3876
DESCRIPTION: 1981, Chicago Pneumatic; Model: T-700WH; Compressor: 900/350; Engine: CAT 3406B Rebuilt < 500 Hours Since; Mounted On: Kenworth Tandem Axle Steer; Truck Engine Make: Diesel; Condition: Price Reduced; Tools/Options: Chicago Pneumatic T-700WH Year: SOLD! 1981: Deep Hole Package, 75K Pullback, 4-Rod Carousel. Deck Engine Recently Rebuilt, approx. 500 Hours Since Rebuild., Rebuilt Dual Tophead Motors and Planetaries, Rebuilt Rotation Pump and Fan Motor/Pump. New Nylotron Head Guides and New Winch Line. Available for an Extra Cost: 3,200' of 4.5" X 30' Drill Pipe with Tandem Axle Pipe Trailer and Mounted IR Tugger Winch and Spare Deck Engine, Skid Mounted Sullair 900/350 Air Compressor, Skid Mounted 2,000 Gallon Fuel Tank, Skid Mounted 300 BBL. Water Tank, Skid Mounted Doghouse, Spare CAT 3406B Engine that needs Rebuilt, 6" Hammer, 12" Hammer/Stabilizer Combo, 12" Tricone, Casing Lifters for both Threaded and Plain End, Casing Slips, Breakout Wrench and J-Wrench. Compressor Hours Unknown. SOLD
Water Truck - SRS #4228
DESCRIPTION: Flatwater; Model: 1,800 Gallon; Mounted On: Unmounted; Tools/Options: 1,800 Gallon Flat Tank and 200 Gallon Fuel Tank. Needs Tool Boxes. Bed has one small leak. Crane Included but Doesn’t Work
Sold - SRS #3603
DESCRIPTION: Bucyrus Erie; Model: 22W Series I; Engine: Ford Industrial 4-Cylinder Gas; Mounted On: 1993 Kodiak 70 Series; Truck Engine Make: 427 Gas; Condition: SOLD; Tools/Options: Bucyrus Erie 22W: Hydraulic Jacks, Catwalk, New Clutches being Installed. Approx. 1,000' of 3/4" Drill Line, has a Drill Line Saver, Sand Reel with approx. 1,200' of Line and a Casing Reel with approx. enough Cable to Run Pipe. Swivel Jack on the Front, Hydraulic Jacks. Mast is not Hydraulic but goes up Easy, Gears are in Good Condition. Truck has Disc Brakes and approx. 91,000 Miles on it, 2nd Owner on the Truck. Tooling Available for an Extra Cost.New Fender Ordered for Truck. SOLD
Parts Tooling - SRS #4220
DESCRIPTION: Monitor; Tools/Options: Monitor 33 gear box and winch spool.
Steel - SRS #4219
DESCRIPTION: Driltech; Tools/Options: 38 Joints of 3.5" X 20’ Driltech Drill Rod. 2-3/8" IF Pin Up. All around 40-50%. Threads are Very Good, Outside is Worn Down Some.
Sold - SRS #4217
DESCRIPTION: 2014, Geo-Loop; Model: 40-500; Engine: Honda; Mounted On: Frame; Condition: SOLD; Tools/Options: Geo-Loop 40-500 Year: 2014: Bought New in 2014 used on a few jobs. SOLD
Rotary C - SRS #4226
DESCRIPTION: CONCRETE CORE DRILL; Engine: PTO; Mounted On: 2001 Low Profile IHC 2000 Series; Truck Engine Make: DT 466E 7.6L; Condition: Fully Operational; Tools/Options: Rock/Concrete Core Drill : 22,000# GVW, Odometer Reads 9,973 Miles. PTO Driven 1,500 PSI Hydraulic System, Remote Operated Hydraulic Boom and Drill Head, 4-Point Outriggers. 300 Gallon Water Capacity and Built-in Pressure Washer also PTO Driven. On Board Honda EB5000X Generator 120/240 30 AMP 120-20 MP. Fully Operational, Ready to Work
Auger - SRS #4224
DESCRIPTION: Simco; Model: 2400; Engine: VH4D Included; Mounted On: Skid; Condition: PRICE REDUCED !!; Tools/Options: Simco 2400 : (1) 10" Diameter Auger 7' Long, (6) 5-1/2" Diameter Augers 5' Long. Also Includes a Wisconsin VH4D Engine.
Sold - SRS #4223
DESCRIPTION: AMS; Condition: SOLD; Tools/Options: AMS auto hammer. Hammer may have 80 hrs. on it. Still has the factory writing on it. Includes the Anvil but not the mount bracket or lift cylinder, used as a swinging hammer SOLD
Sold - SRS #4222
DESCRIPTION: MudSlayer; Model: M500; Engine: None; Mounted On: Skid; Condition: SOLD; Tools/Options: MudSlayer M500: SOLD No Motor, Must be Hooked up to Auxiliary Power. Two 2X3 Centrifugal Pumps, One for Discharge and One to Select between Mixing Hopper, De-Sanding Cones and Cleanout. Shaker Screens in Great Shape, Powder Coat in Great Shape. Skid has Three Leveling Jacks. No Hour Meter. Overall in great condition but could use a few hydraulic leaks fixed here and there but nothing major.
Sold - SRS #4211
DESCRIPTION: Flatwater Fleet; Mounted On: 1994 Ford L9000; Truck Engine Make: CAT 3306; Condition: SOLD; Tools/Options: ONE OWNER 2,500 Gallon Flat tank with IMT 6,000# Crane with Remote Control, 2" Water Pump, Night Lighting Package, Fuel Cell with Hose Reel. Truck has an Eaton Fuller Transmission. Truck has 258,567 Miles on it.. SOLD
Sold - SRS #4208
DESCRIPTION: Simco; Model: 2800; Compressor: 185 CFM - NEW 12 Hours on it; Mud Pump: 3X2X13 Centrifugal; Engine: PTO; Mounted On: 2005 Ford F-550 4WD; Truck Engine Make: 6.0 L Diesel that has been Bullet Proofed; Condition: SOLD; Tools/Options: Simco 2800: Engine has been Bullet Proofed, Odometer Reads 82,891 Miles and it has approx. 4,700 Engine Hours. New Compressor that Currently has only 12 Hours on it. Sandline, Rod Box, Driller Platform, Two Rear Jacks. Rig has New Chains for Mast, New Housing Wear Plate and Impeller in the Mud Pump. Owner believes the Simco is a 2002 Year Model. Includes Mud Pan and 280' of 3" OD Flush Joint 2-3/8" Mayhew Jr Thread Drill Rod. SOLD
Sold - SRS #4083
DESCRIPTION: 2016, GEFCO; Model: SS-22-RC-HD; Compressor: 500 CFM; Mud Pump: 6" X 8" Hydraulic; Engine: PTO; Mounted On: 2016 Peterbilt 367; Truck Engine Make: Cummins X15 565 HP; Condition: SOLD; Tools/Options: GEFCO SS-22-RC-HD TEMPORARILY OFF MARKET. Year: 2016: 18", 150KTable that Opens to 36" Square Opening, Set up to run 30' Drill Pipe, 6" Western Rubber Swivel that was Rebuilt in 2022. Approx. 1,100 Compressor Hours. Truck has approx. 4,300 Hours and 5,000 Miles, Working Drill, Hours have Increased. 22,000# Front Axle, 46,000# Rears. Includes a 1995 45' Trailer, New Floor and Headache Rack, New Running Gear, Brakes, Hubs, Drums. 900' of 6-5/8" Matrix Smooth Flow 20' Drill Pipe,(1) 6-5/8" Matrix Smooth flow Pin & Box Matrix Stabilizer 23" OD,(1) 6-5/8" Matrix Smooth Flow Pin & Box Matrix Wing 19-1/2" Stabilizer, (4) 6-5/8" Matrix Smooth Flow Hole Opener 22", 23", (2) 26", (3) 6-5/8" Matrix Smooth Flow Saver Subs, (2) Oilfield Breakout Wrenches, (2) 8" Square Tube Jack Stabilizers, (10) 1.25" PVC/SS Internal Air Line, (2) Breakout Table Jaw Sets, (3) 15-7/8" Matrix 6-5/8" Smooth Flow Thread Lead Bits, (2) Starter Wing Bits 24", 28", (4) NE Replacement Jacks for Rig - New, Misc. Parts, Filters, Plates, Hoist Hooks, Breakout Wrench Parts.
Sold - SRS #4168
DESCRIPTION: 1978, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Mud Pump: Removed; Engine: PTO; Mounted On: 1978 IHC Paystar; Truck Engine Make: Detroit 8V92; Condition: price reduced; Tools/Options: Ingersoll Rand TH-60 Year: 1978: PRICE REDUCED (3) Hydraulic Leveling Jacks, Rod Rack, Water Injection Pump, Hammer Oiler, 7-Rod Carousel. Set up to Run 3.5" Drill Pipe, Pipe & Tooling Available for an Extra Cost. Rebuilt Funk Box (Bearings & Seals), New Head Bearings & Seals, New Myers Water Pump. All Filters and Fluid Changed, New Drive Shaft in the Drive Line. Some Hydraulic Hoses Replaced, New Air Lines.
Sold - SRS #4196
DESCRIPTION: 2022, Mud Slayer; Model: M350; Mounted On: Rubber Tracks; Condition: Near New - SOLD; Tools/Options: Mud Slayer M350 Year: 2022: SOLD Near New, Only 135 Hours, Equipped with Suction Hookups, Lift Pump, Shaker and (4) Jacks. Includes a Dual Wheel Tilt bed Trailer, 24" and 30" Augers.
Sold - SRS #4172
DESCRIPTION: Speedstar; Model: 71; Engine: Deutz Diesel; Mounted On: 1993 IHC; Truck Engine Make: Cummins Diesel; Condition: SOLD; Tools/Options: Speedstar SS-71: 3-Line Machine, 3 Hydraulic Jacks. Truck has a 10-Speed Transmission. Will Include (1) Stem and (1) Bailer. Other Tooling Available for an extra cost. Spade, Stems, Bits to 18" SOLD
Sold - SRS #4180
DESCRIPTION: 2002, Ingersoll Rand; Model: TH-60 Long Tower; Compressor: 825/350; Mud Pump: 4X3X13 Mission; Engine: PTO; Mounted On: IHC Paystar; Truck Engine Make: CAT 3406 550 HP C15; Tools/Options: Ingersoll Rand TH-60 Long Tower Year: 2002 : SOLD 9-Rod, 4" Carousel (7-Rod 4.5" also available), 20 GPM CAT Water Injection, Braden Main Winch. 17,951 Total Rig Hours, 5,199 Compressor Hours and 544,056 Miles on the Truck. 400' of 4" Drill Rod Available.
Compressors - SRS #4091
DESCRIPTION: Compressor: LGEI 900/350 (built by Sullair); Engine: CAT C15; Condition: Working Unit OPEN TO OFFERS; Tools/Options: LGEI 900/350: Compressor was Built Like a Sullair. Engine Hour Meter Currently Reads 617, Compressor Hours Unknown.
Sold - SRS #3334
DESCRIPTION: Failing; Model: Jed A RC; Compressor: IR 260/120 - See Below; Mud Pump: Skid Mounted; Engine: Cummins Diesel (Hospital Enclosure); Mounted On: Trailer; Condition: SOLD; Tools/Options: Failing Jed A RC: Rig is set up for Reverse Circulation, Internal Air on Swivel. Needs Paint but is in good Operating Condition. Engine is in a Hospital Enclosure and runs Quiet. 18" Table, 8,000# 6-Part Main Winch Line, 8,000# 5-Part Hoisting Line, and also has a Sand Line with 1,000' of Cable, 50', 90,000# Mast. 10' 6" Kelly (could accommodate a 20' kelly), Four Hydraulic Jacks. Table Rebuilt in 2018. Includes a Trailer Mounted Sullair Compressor Engine is Newer, 40' Trailer with approx. 500' + of 6" Drill Rod (20' and 10' Joints), Tooling to set up and Drill, 20' Dog House on Trailer with Small Hand Tools to run Job, 2 Year old Miller Welder. SOLD
Sold - SRS #4205
DESCRIPTION: Failing; Model: CF-15; Compressor: LeRoi 256 SDS; Mud Pump: GD FD-FXX 5-1/2" X 8"; Engine: PTO; Mounted On: IHC F2574; Truck Engine Make: Detroit 671; Condition: Excellent, Runs Great; Tools/Options: Failing CF-15: Double Drum Leebus Grooved Drawworks with 5/8" Wire Rope, Air Clutch Engaged. 2" Standpipe and Kelly Hose, 8" Failing Retractable Rotary Table with 4-Speed Transmission. 25' X 4" Fluted Kelly with 2-3/8" IF Pin, Chain Driven Hydraulic Pulldown, 2" Little Giant Swivel, 38' Mast, Breakout Tongs, (4) Leveling Jacks at each Drill Frame Corner, Pipe Rack, Full Width Platform with Removable Center. Truck has a 200 Gallon Diesel Tank, Fuller Road Ranger RTO9513 Transmission, Failing, PTO, Tires in Excellent Condition with Flotation Tires in the Front, all New Wheel Bearings & Seals. Bill of Sale Only.
Sold - SRS #4183
DESCRIPTION: 2000, Driltech; Model: T25KW; Compressor: Sullair 1000/350; Engine: CAT 3406E; Mounted On: 2000 Ford Sterling; Truck Engine Make: CAT C12; Condition: SOLD; Tools/Options: Driltech T25KW Year: 2000: 20 GPM Bean Water Pump, 10 Gallon RDO Oiler Box.. Rig has approx. 16,000 Total Hours. Deck Engine was Rebuilt in 2011, has approx. 8,400 Hours on it. Compressor has approx. 1,025 Hours on it, replaced in March 2022. Truck has approx. 69,000 Miles on it, 10-Speed Manual Transmission with Hi-Lo Range, Jake Brake. Maintenance Records Available upon Request. Includes 420' of 4.5" Drill Rod, 6" & 8" DTH Hammers and Misc. Hand Tools. Also includes a WATER TRUCK, 2000 Ford F-650 with 141,000 Miles, 750 Gallon Water Tank and 250 Gallon Fuel Tank, 6-Sped Manual Transmission Powered by a Cummins 5.9L Engine, Under CDL. 2009 IHC Maxxforce GROUT/PUMP TRUCK Powered by an IHC Dura Star Engine, 6-Speed Transmission, approx. 89,000 Miles on it. There is a cement Mixer on the back, 200 Gallon Water Tank and Multiple Tool Boxes, CDL Required. 2001 DITCH WITCH 3700 TRENCHER with H313 Digging Attachment, All Hydrostatic and has 2,200 Total Hours, CUSTOM TRAILER goes with it, 2" Ball Receiver. The Pump Grouter is a DSI Model with a 16 HP Briggs and Stratton Engine. Hasn’t been used much Recently. HYDROFRAC MACHINE has a TelePlex 50 GPM Pump Unit and a 4-Cylinder Gasoline Continental Engine that has been Rebuilt (includes a Packer). Two Water Tanks that go with the Frac Machine. One is 1,000 Gallon and the other is 2,000 Gallon and has a crack at the very Top. Manuals available for all of the equipment. There is an Extra 500' of 4.5" Drill Rod for a Total of 920'. Also Includes 12 Rig Mats, 55 Gallon Drums with Air Pumps of RDO, Compressor and Hydraulic Oil for the Rig along with Many Extra Parts for all the Equipment.. SOLD
Sold - SRS #4159
DESCRIPTION: Mounted On: 2002 Kenworth; Truck Engine Make: 455 HP; Condition: SOLD; Tools/Options: 2,500 Gallon Flat Tank, Fuel Pump, Fuel Transfer Tank, Tool Boxes, Pipe Rack. Well Maintained. Truck has a 13-Speed Eaton Transmission, Jake Brake and approx. 980,000 Miles on it. Truck Engine was Replaced about 250,000 Miles ago with a Rebuilt Engine. SOLD
Sold - SRS #4204
DESCRIPTION: 2004, CME; Model: 550X; Engine: PTO; Mounted On: Buggy; Truck Engine Make: Cummins; Condition: Runs Great; Tools/Options: CME 550X Year: 2004: Rig has 4,600 Hours, Auto Hammer, Angle Package, Three Winches plus a Wireline, 8 Series Moyno, New Coupler, Bearing Plates, U-Joints. Runs Great. SOLD
Auger - SRS #4203
DESCRIPTION: 1995, Mobile; Model: B47; Engine: PTO; Mounted On: Marooka Tracks; Truck Engine Make: Deutz Diesel; Condition: Runs Great; Tools/Options: Mobile B47 Year: 1995 Cathead, Winch, Hydraulically Drive. Runs Great.
Auger - SRS #4202
DESCRIPTION: 2015, Kubota; Mud Pump: Capable of One; Engine: PTO; Mounted On: Rubber Tracks; Truck Engine Make: D1105 - 2008 Tier 4; Tools/Options: Kubota Year: 2015: 210 Hours, Near New, No Auto Hammer. Drill can Auger or Mud Rotary Drill with External Pump, Room on Board for one. Capable of up to 4.25" Augers. There is a Place on Board for one. Tooling available for an extra cost.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |