Rigs
Sold - SRS #4378
DESCRIPTION: 1979, Bucyrus Erie; Model: 22W Series III; Engine: 4-Cylinder Deutz Diesel Air Cooled; Mounted On: 1985 IHC S2500; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Bucyrus Erie 22W Series III Year: 1979: SOLD 3 Hydraulic Outriggers, Tool Guide, No Cat Head. Hydraulics were added to the rig. Truck has an Eaton Fuller Transmission and approx. 200,877 Miles on it. Includes a Rope Socket. Belt Guard will be Reinstalled. Drill has 5/8" Drill Line, Lengths of Cable Unknown. It was being used to drill 100' to 200' Water Wells. Includes a Rope Socket. Road Legal. SOLD
Parts Tooling - SRS #4392
DESCRIPTION: Weldco Beals; Model: 615; Condition: Working Order; Tools/Options: Weldco Beals 615 Casing Hammer.
Pump Hoist - SRS #4390
DESCRIPTION: Mounted On: 2002 Ford F350 4WD; Truck Engine Make: 7.3L; Tools/Options: Truck has 250,000 Miles on it, Engine has been rebuilt. Hoist is set up like an old Cooper rig but with hydraulic rams on the pole & outriggers. Manual drum with free fall and big hand brakes. 36' Mast, Owner says it has 21,000# Pull Capacity
Water Truck - SRS #4391
DESCRIPTION: 1998, Flatwater Fleet; Model: RTB3200X; Mounted On: 1997 Navistar 2674 6X4; Truck Engine Make: Cummins M11 Plus 450 HP; Condition: Garage Kept; Tools/Options: Flatwater Fleet RTB3200X Year: 1998 1997 Navistar 2674 6X4: 3,200 Gallon Flatwater Fleet Water Bed, Crane, Auto Greasing system. Odometer Reads 43,055 Miles, 450 HP Engine
Truck - SRS #4388
DESCRIPTION: 2004, Mack; Model: Granite Day Cab CX613; Engine: Diesel; Tools/Options: 800,000 + Miles. Tandem Axle, 40' Flat Deck Traveling Axle Hydraulic Trailer with Recovery Winch. Runs Good. A/C Works, Wet Line Kit. 12K Front Axle and 20K Rears. Can be sold as a package with a track mounted 2011 Versa Drill V50GTRX and a 2011 truck mounted Deeprock 150 for extra cost.
Rotary D - SRS #4387
DESCRIPTION: 2011, Deeprock; Model: 150; Mud Pump: Mission 4X3; Engine: Perkins Diesel; Mounted On: 2011 Ford F650; Condition: Ready to Drill; Tools/Options: Deeprock 150 Year: 2011: Auto rod handler allows for single person operation. Low Miles on Truck. Includes 300' of 2-3/8" X 10' Mayhew Jr. Rod. Can be sold as a package with a track mounted 2011 Versa Drill V50GTRX and a 2004 Mack Granite with 40' Flat Deck Hydraulic Trailer for extra cost.
Sold - SRS #4385
DESCRIPTION: 2000, Driltech; Model: D25; Compressor: 1000/500; Engine: CAT 3406e; Mounted On: Sterling; Truck Engine Make: 420 HP CAT C12; Condition: Working Drill Great Price SOLD; Tools/Options: Driltech D25 Year: 2000: SOLD Currently has approx. 3,800 Hours since Engine Rebuild and approx. 4,500 since Compressor was Replaced. New Chains & Sprockets, New Tophead Slides. Winch is 1 Year Old. Bottom Stacker Valve on Control Panel was Replaced approx. 2 Years Ago. Most Work was done in the Last 2 Years. Will be Set up to Run 4.5" Drill Rod, 4 Jacks, Pipe Rack. Truck has a 10-Speed Transmission and approx. 67,000 Miles on it. Not available until the end of October. No Pipe Included. SOLD
Sold - SRS #4307
DESCRIPTION: 1988, Speedstar; Model: Star 25K; Compressor: 900/350; Mud Pump: 3X4; Engine: PTO; Mounted On: 1988 Paystar 5000; Truck Engine Make: 400 HP Diesel; Condition: PRICE REDUCED; Tools/Options: Speedstar 25K Year: 1988: Rig has some 30K Components on it also, Hydraulic Motor and Pump Set Up are 30K. Sandline, Breakout Wrench, Pipe Spinner, 6-Pod Carousel (carries 120' in the carousel & 280' in the rod box), Rod Loader, 19" X 24 Table. Four Jacks. Back in the 1990's it had it's 2nd 400 HP Engine Installed. Includes approx. 700' of Drill Rod, Rig is Set Up to Run 4.5" X 20' Drill Rod with 3.5" Regular Threads Box and Pin, Bits, a Mud Shaker Powered by a 50 HP 3-Cylinder Diesel, all Mechanical Pick Up Tube. and an Extra Hydraulic Motor for the Tophead along with a bunch of parts. Drill has a Few Hydraulic Rams Leaking that the Owner is willing to Repair.
Rotary C - SRS #4297
DESCRIPTION: 1984, Challenger; Model: 361; Mud Pump: See Below; Engine: (2) CAT 3406C; Mounted On: Sub Structure; Tools/Options: Challenger 361: 850 HP Double Drum Stacked Drawworks with Hoisting & Kelly Drum. Compounded CAT Engines are 400 HP, Allison Automatic Transmission, 24" Hydromatic Brake. 3-Sheave 24" 100-Ton Hook Hoist, 3-Sheave 24" 100-Ton Kelly Hook Traveling Blocks. 3-1/2" Howard Turner Swivel, Western Rubber 6WC RC Swivel, 4-1/2" Square OD Kelly, 6" OD Square Kelly for Flooded Reverse Drilling. Challenger Model 240-84, 240,000# Hook Load, API Rated for 6-Lines, Mas is 84' from Top of Rotary Deck to Bottom of Crown, 24" Crown Sheaves Grooved for 1" Wire Rope, 11' KB Substructure Rated at 480,000#. Racking Platform Capable of Racking 5,600' of 4.5" Drill Pipe and 7,500' of 3.5" Drill Pipe. Mud System Tank is 30' Long X 4' High with 193 bbl.. Capacity, 4' X 6' Sand Trap - 38 bbl.., Settling Pit is 5'4" - 32 bbl.., Compartment One is 19' X 4' - 122 bbl.. 2-NOV Brandt Linear Shale Shakers Rated at 400 GPM each with .084 Screens, Blow bbl. Air/Gas Separator, 12-Cone Brandt Desilter, 2-Cone Harrisburg Cone Desander. HFF-1000 6-3/4 X 10 Triplex PBA V12 Detroit Diesel. Secondary Mud Pump is a Unitized Skid Mounted High Volume Dowell Triplex Mounted on Mud Tank. 7-3/4" X 8" 850 HP Triplex with a 17' X 5' Mud Tank. This Unit is Powered by Two Tandem Mounted CAT 34068 Engines. 450 kW Cummins Onan Generator PBA a Cummins KTA19G3 (approx. 1500 Hours). 18" Howard Turner Rotary Table, 3" ID Rotary Hose Rated at 5,000 PSI Working Pressure, 7,500 PSI Tested with 4" API Male Threads each End. 6" Flooded Reverse Material Hose. Auxiliary Equipment Includes 69' Catwalk with V-Door, 3,000 Gallon Fuel Tank with Parts House, Elevated Hydraulic Dog House, 2-Quadco Weight Indicators/Current Calibration Docs, Sub & Tool Skid, Type C Tongs, 6,000# Gearmatic Hydraulic Floor Winch, 6,000' Wireline Winch for Survey Tool, Current LED Yard & Rig Lighting per IADC Code, Plug & Play Electrical House with Safety Protection, 96 Joints of 4.5" XH Drill Pipe (approx. 3,000'). 30' Long X 4' High Tank with 193 bbl. Capacity, (2) 7.5 HP Morse Agitators, Two Drill Pipe Baskets, Compartment 2, 4" Double Life Mud Hopper, 50 HP 6 X 5 X 14 Centrifugal Pump, Pit will Accommodate 10" Flood Line for Reverse Drilling, Total Mud Tank Capacity is 385 bbl. LED Lighting System is < 1 Year old. Newer Primary Mud Pump. Package Includes Drill, Doghouse and Generator. Everything else is an extra cost.
Mud Grout Pumps - SRS #4384
DESCRIPTION: Mud Pump: Gardner Denver 7.25" X 14" Duplex FK FXK; Engine: 871 Diesel; Mounted On: 1983 Fontaine Tri-Axle Trailer; Condition: Great; Tools/Options: Gardner Denver 7.25" X 14" Duplex FK FXK Mud Pump with Power. Chrome Lined Cylinders, 900 GPH, 900 PSI. Matco Quick Change Head. Also Includes a Mounted 17,000# Capacity Palfinger PK 17502 Crane with Hydraulic Outriggers Powered by an Isuzu Diesel. Wireless Remote for Crane. All Systems Work, Excellent Condition.
Parts Tooling - SRS #4383
DESCRIPTION: Tools/Options: Upsy Daisey Pump Pullers, Two Available. 3/4 HP Engines
Sold - SRS #4254
DESCRIPTION: 2006, Reichdrill; Model: T-650 D II; Compressor: Sullair 900/350; Engine: CAT 3406; Truck Engine Make: Mack Diesel; Condition: SOLD; Tools/Options: Reichdrill T-650 D II Year: 2006: SOLD Deck Engine & Compressor has < 600 Hours on it, both were Rebuilt. 38,000# Pullback, Jib, Water Injection Pump (tank removed), Hammer Oiler, 8-Rod Carousel, Dust Collector, No Rod Box, (1) Front and (2) Rear Jacks. 8 New Drive Tires, Valve Banks Resealed, Rebuilt Air on/off Solenoid for Compressor, 90% New Hoses, New: Cooler Fan Motor, Deck Batters, Dust Filters, Hammer Oiler Adj. Valve, Air Line from Head, Throttle Cable, Compressor Exhaust, Pump on Funk Box, AC Motor, Table Bushing, Truck Alternator, all Recently New. Includes (4) New 4.5" X 25' Drill Rods < 500', New 6" Hammer and 6-1/4" Bit with < 300. Truck has 56,612 Miles on it and approx. 15,245 Engine Hours. SOLD
Sold - SRS #4330
DESCRIPTION: 1998, Versa-Drill; Model: V100; Compressor: 300/200 - Needs Rebuilt; Mud Pump: GD 5X6 and 3X4; Engine: PTO; Mounted On: 1998 IHC 6X6; Truck Engine Make: DT 530 E; Tires: New; Condition: SOLD; Tools/Options: Versa-Drill V-100 Year: 1998: Remanufactured Engine < 500 Hours Ago, at the same time had New Aluminum Fuel Tanks Installed, Newer Rotation Pump (<500 Hours). Four Jacks, Pipe Rack, 7-Pod Carousel. Painted within the last few years and had a hydraulic motor added to handle a mud guzzler. Control panel isn't labeled and compressor needs rebuilt. Rig is Set Up to Run 3.5" O.D. X 20' Drill Rod with 2-3/8" IF Threads. No Drill Rod Available. Truck has a 7-Speed Standard Transmission. Odometer Reads 93,419, accuracy not guaranteed. SOLD
Sold - SRS #4380
DESCRIPTION: 1995, Ingersoll Rand; Model: TH-60; Compressor: IR 900/350 HR2; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: 2012 Peterbilt; Truck Engine Make: Cummins ISX15 525 HP; Condition: SOLD; Tools/Options: Ingersoll Rand TH-60: SOLD Rebuilt & Remounted. Set Up to Run 4.5" Drill Pipe, 18 GPM CAT Water Injection Pump, Sandreel (no rope but some may be able to be provided), Downhole Lubricator, Driller & Helper Platforms,. All New Hoses and Pumps, Sand Blasted and Painted, Replaced Pulldown Cables, Tophead Drive Gearbox, Replaced Bushings in all Feed & Winch Sheaves, Reworked Control Panel with New Gauges, Switches, Valves, etc., Installed New Carousel Rotation Gearbox, Replaced 3.5" Carousel with a 4.5" used one, Installed New Swing Table Assembly and New Under Rob Box Tool Box, Fluids & Filters Serviced, Repacked Leveling Jacks and Pulldown Cylinder, New Seals in Hydraulic Controls, Fabricated New Slide Table & Repaired Table Slide Tracks, Installed New Packing in Fluid Swivel, New LED Lights, Updated Throttle Controls to Newer Truck, Rebuilt UL 88 Assemble .Complete Rebuild List Available. Odometer Reads 8,804 Hours and 66,617 Miles. SOLD
Auger - SRS #4379
DESCRIPTION: 2015, Diedrich ; Model: D50 Turbo; Engine: PTO; Mounted On: 1987 Ardco Buggy Refurbished in 2015; Truck Engine Make: Detroit Diesel; Condition: Good; Tools/Options: Diedrich D50 Turbo Year: 2015: Ardco Buggy was Refurbished in 2015. 21' Mast, Runs AWJ & NWJ Rod, Capable of 3" - 6" or Larger Casing. Auto Hammer, Capable of up to 250' Depths. 9,012 ft-lbs. Rotary Torque, 14,452# Pulldown, Moyno 3L6. 3 Winches, Auger Rack, Slide Base, In/out Wiggle Tail, 4 Hydraulic Jacks. Rig has approx. 5,700 Hours on it. Rig is Capable of SPT, CPT, Rock & Wireline Coring, Sampling, Auger, No Breakout Wrench, Rod Clamp, Water Tank, Cathead.. No Rod or Tooling Available.
Sold - SRS #4192
DESCRIPTION: 1996, Schramm; Model: T450WS; Compressor: 815/350 with Clutch; Engine: Detroit; Mounted On: 1995 Ford; Truck Engine Make: Ford; Condition: SOLD; Tools/Options: Schramm T450WS Year: 1996: SOLD Drill is set up to run 3.5" Drill Rod. 30.5' Mast, Rated at 32,000# Pullback, No Sandline, Single Winch, 3 Hydraulic Jacks, Pipe Rack, Bean Water Injection. Oiler does not work. Compressor Clutch has been Replaced. Truck has an Eaton Fuller 13-Speed Transmission, Two Fuel Tanks, one 50 Gallon and one120 Gallon, Odometer Currently Reads 73,402 Miles. Rebuilt Engine Installed in 2016. No Carousel. Rig is Currently having new Bearings Installed in the Winch, Freshly Painted. SOLD
Sold - SRS #4110
DESCRIPTION: Mounted On: 2001 Peterbilt 357 6X4; Truck Engine Make: Cummins 305 HP; Condition: SOLD; Tools/Options: 2,000 Gallon Tank, 6,000# Crane, 20' Bed. Truck Currently has 152,269 Miles and 2,619 Hours, Full Lockers, No Jake Brake, 8-Speed Transmission, Cruise Control and AC. SOLD
Sold - SRS #4364
DESCRIPTION: 1989, Speedstar; Model: Mini Star; Compressor: Developmental; Mud Pump: Centrifugal; Engine: John Deere; Mounted On: 1996 Chevrolet 2WD; Truck Engine Make: CAT C7; Condition: SOLD; Tools/Options: Speedstar Mini Star Year: 1989: SOLD Everything Works but Needs TLC & Attention. 12K Pullback & Pulldown, 4K Winch, Driller & Helper Platforms, Rod Box, Set Up to Run 2-3/8" IF Drill Rod. Small Tophead Drive Under CDL. Mud Pump is only a few years old and bottom end was rebuilt not long ago. Includes some Extra Parts, No Drill Pipe Available. Road Worthy, DOT Inspected. SOLD
Sold - SRS #4376
DESCRIPTION: Dresser; Model: T70W; Compressor: None; Mud Pump: None; Engine: PTO; Mounted On: 1981 4-Axle Crane Carrier; Truck Engine Make: Detroit 50 Series; Tools/Options: Dresser T70W: Versatile Tophead Drive/Drawworks Combination. Rig was Rebuilt in 2006 with all New Modern Hydraulics and a Newer Model Detroit Engine Replacement. Standard 41'7" Mast Clearance for Handling Range II Pipe, Two Mast Raising Cylinders - Combination of 70K Pullback, Tophead drive has 0-120 RPM and 5,000 ft./lbs. Torque, Hydraulic Powered Drawworks with 4-Part 5/8" Traveling Block for Fast Hole Tripping Operations, Drillers Platform Work Area, 27" Table Opening with Unique Slip Inserts for Different Size Casing and Drill Pipe, Holds both Vertical and Horizontal Directions, 2-Sets of Web Wilson Tongs Hung on Lines, Extra Hydraulic Winch, Wireline Winch, Drill Pipe Spinner, (3) 48" Hydraulic Leveling Jacks, 25 GPM Water Injection, Single Rod Handler, Pivoting Jib Boom. < 7,000 Hours. Fuller RTO 10-Speed Transmission. Carrier Engine Powers all Hydraulics. Recently tankan into the shop for inspection and ready to go. SOLD
Rotary E-F - SRS #4234
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6; Engine: PTO; Mounted On: 1994 Ford L8000; Truck Engine Make: Cummins; Tools/Options: Failing 1500: 5-1/2" Stationary Rotary Table, 20' Kelly, Mechanical Clutches, 2 Front and 2 Rear Jacks, Driller & Helper Platforms, Catwalk, Rod Box. Truck has an Eaton Fuller 8-Speed Transmission with Lo-Lo. Includes 300' of drill rod, 2 drill bits with subs, table catch, new kelly with pins. Also just put in new pump sleaves and pistons .
Sold - SRS #4375
DESCRIPTION: 2001 , Foremost; Model: DR 24; Compressor: Atlas Copco 900/350; Mounted On: 2001 Kenworth T800; Truck Engine Year: PTO; Truck Engine Make: CAT C15 475 HP; Condition: SOLD; Tools/Options: Foremost DR-24 Year: 2001: RIG HAS BEEN SOLD 58,000# Pullback, Lower Casing Drive 1,000,000 in./lbs. Torque, 12' Stroke, 6,000# Pull Jib Boom Winch, Hydraulic Water/Foam Injection. 9,947 total Rig Hours. 61,700# GVW. Includes 580' (29 Joints) of 18" X 20' Drill Pipe, (2) Pieces of 18" X 12'8" Starter Pipe, (1) Used Numa 18" Downhole Hammer. Truck Engine has approx. 23,328 Hours.
Pump Hoist - SRS #4371
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 1997 Ford Super Duty 2WD; Truck Engine Make: Gas; Tools/Options: Smeal 5T: Truck has a 5-Speed Manual Transmission, Remanufactured Engine. 157,237 Chassis Miles. No Remote, Sandline Operates but no Cable on Drum. Tool Boxes, Pipe Rack, Hydraulic Outriggers. Hoist is only used a few times a month.
Sold - SRS #4239
DESCRIPTION: 1976, Speedstar; Model: SS-15; Compressor: See Below; Mud Pump: 5X6 & a Centrifugal; Mounted On: CCC; Truck Engine Make: Cummins 290; Condition: SOLD; Tools/Options: Speedstar SS-15 SOLD Year: 1976: 8-1/2" Retractable Table. Centrifugal mud pump was never used, condition unknown. Air compressor not mounted. Long Mast, can pick up 45'ers. Rig is Set Up to Run 3.5" IF Drill Pipe. SOLD
Sold - SRS #4318
DESCRIPTION: 2018, EPIROC; Model: Diamondback 40; Compressor: 1070/350 with Clutch; Mud Pump: 7.5" X 10"; Engine: PTO; Mounted On: 2019 Peterbilt 367; Truck Engine Make: Cummins X15 600 HP; Condition: SOLD; Tools/Options: EPIROC Diamondback 40 Year: 2018: SOLD Centerline Mud Pump: Drillers Console, Cyclone Hydraulic Tank, Primary Hydraulics, Rear Jack Module, Mud & Air Hosing, Lighting, Electrical Wiring for Standard Options, Tower Trunnion, Tower Raising Cylinders, Mud & Air Piping Valves Nordstrom and Operated Hydraulically from the Drillers Console. Compressor Module includes Oil Cooler, Hydraulic Oil Cooler and Oil Separator Tank. Electronic Air Regulation System for Control over Volume and Pressure. Namco Box includes Compressor Disconnect Function to fully Disengage Compressor. Standard 34' Derrick with 40,000# Pullback and 30,000# Pulldown with all Hoses, Carriage and Feed System. Duplex Mud Pump that Produces 300 GPM @ 350 psi. 3" ID Head. 8,000 Ft-lbs@107 RPM 2-Speed Rotary Head and 5,362 Ft-lbs.@ 161 RPM. Top Bearing Lubricated with an Oil Pump. 0-184 Variable Control, 3" ID through the Head. 9-Piece X 3.5" Fixed Carousel with capability to remove or load rods from the side of carousel. 24" Table (T3W/TH-60 style) with Hydraulically Sliding Wrench which Slides from the Center Rear of the Table. The Rear of the Table Slides Hydraulically to give more room around the Table or to Clamp Casing in the Table. The Table has a 12.88" Bushing Insert that Bolts in the Outer Adapter. The Front of the Table is Pinned either Side to Allow for Pivoting to the Driller's or Helper's Side. The Table Front can also be Removed. 25 GPM Bean Water Injection with Foam, 18,000# 1-Part Main Winch, Braden Winch that Mounts to a Saddle on the back of the Tower. Jib, comes in the Kit and is Bolted to the Crown of the Tower. Winch is operated from the Driller Side. Sandreel Winch. Petol Breakout Wrench is bolted to the Helpers Side of the Tower, Wrench is Operated from the Drillers Console. Manual Included. Stand Alone Rod Box with Slide, Rod Spinner, Torque Limit Control, 7-Gallon Electric DHD Lubricator, Hydraulic Welder, Hub Odometer, Toolbox, Decking Located above DHD Lube Tank for Additional Storage Space. Truck has 22,000# Front Axles and 46,000# Rears, Differential Lock on both Rear Axles, Namco Transfer Case to Engage and Disengage Drilling Functions. Standard 247" Wheelbase, Fuller Transmission. Drill is set up to run 3.5" OD Pipe with 2-5/8" Threads. Rig is Capable of Carrying 480' of Pipe, 9 Rods in the Carousel and 15 in the Pipe Rack. Includes Pipe in the Carousel, 180', some Bits and Two Collars. More Pipe is Available for an Extra Cost. Odometer Reads 32,729 Miles and Cab Hour Meter Shows 4,656 Engine Hours and 1,480 Compressor Hours. Mfg. Specs above to be Confirmed. SOLD
Rotary E-F - SRS #4360
DESCRIPTION: 1979, Failing; Model: 1250 Holemaster; Compressor: 650/250; Mud Pump: (2) Failing 5X6; Mounted On: Ford LT9000; Condition: Ready to Work; Tools/Options: Failing 1250 Holemaster Year: 1979: Drill has been Rebuilt. Two Mud Pumps and Two Hydraulic Pumps, Injection Pump, Pickup Pump. 5-1/4" Retractable Table. Loop Hose Reel and Extra Bailing Line/Stinger Line, Dual Fuel Tanks, Retractable Table, Rod Box Holds 20' Pipe. Refurbished & Warrantied Motor Installed 2023. Entire Drive Train was changed as well.
Sold - SRS #4359
DESCRIPTION: 1989, Reichdrill; Model: T-625W; Compressor: Sullair Twin Screw 850/350; Mud Pump: Wilden (newer); Engine: CAT 3406B; Mounted On: IHC F-2544; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Reichdrill T-625W Year: 1989: SOLD New 2-Cylinder FMC Water Injection Pump, Electric Lubricator, Operator & Helper Platforms, Helper Walkway, Vandal Cover, 650 Style Rod Loader, 12 Piece Pipe Rack. 65K Original Miles & 14K Original Hours. New FMC Pump, Rotary Head, Bullshaft, Bearings & Seals, Races. Includes 420' of CP Rod. SOLD
Parts Tooling - SRS #4358
DESCRIPTION: Cyclone; Model: 35R; Tools/Options: Mast and Turntable off of a Cyclone 35R.
Sold - SRS #4355
DESCRIPTION: Mud Puppy; Model: 255 2SC; Engine: Deutz 73 HP; Mounted On: Trailer; Condition: SOLD; Tools/Options: Mud Puppy MP 255 2SC: Model T11 Sand Guzzler & Model 118 Centrifugal Desander Pump, 1,000 Gallon Tank. All New Hoses on Unit, New 118 Desander Pump all Replaced at 1,677 Hours. Two Sand Guzzlers, Includes all Suction Hoses. Changed Hydraulic Oil & Filters and Replaced all New Sand Cones at 1,677 Hours. Inside of the Tank was Sealed to Prevent Rust. UNIT HAS BEEN SOLD
Truck - SRS #4357
DESCRIPTION: Mounted On: 2017 Freightliner 4X2 Flatbed; Truck Engine Make: 525 HP; Condition: Ready to Work; Tools/Options: M211242S Freightliner, 23' Long Flatbed, Cathead Pipe Racking Capabilities using External Power. Odometer Reads 114,868 Miles.
Compressors - SRS #4353
DESCRIPTION: 2002, Ingersoll Rand; Model: XHP-900/350; Engine: CAT 3406; Mounted On: Skids includes Trailer; Tools/Options: Low Hours. Can be Sold without the Trailer for Less.
Sold - SRS #4352
DESCRIPTION: Semco; Model: S6000; Engine: 3-Cylinder Diesel; Mounted On: 2002 Ford F350 4WD Extended Cab; Truck Engine Make: 7.3L; Condition: Working; Tools/Options: Semco S6000: Extended Cab. UNIT HAS BEEN SOLD. Includes 5 Pipe Wrenches and (2) 1" Elevators. No Sandline, 35' Mast Extended. Brand New Hydraulic Pump, Replaced almost all of the Hydraulic Lines. Regular Maintenance and Repairs done. Not perfect but it does the job. Will sell just the Hoist.
Sold - SRS #4329
DESCRIPTION: Failing; Model: 1250; Compressor: 100 CFM/125 psi @ 1,000 rpm; Mud Pump: 5" X 6-1/2" Piston; Engine: PTO; Mounted On: 1990 IHC; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Failing 1250: SOLD Two Stage Air Compressor, 8-1/2" Mayhew Hydraulic Sliding Table, Little Giant 2" Swivel on Kelly, Kelly was Replaced in 2022 with Kelly Savers. Sandline, Mud Pit with 4" Suction Hose & Sleeve. Truck has a 10-Speed Transmission with Low Range Deep Reduction, Power Inverter Wired in Cab to Run a 110 Volt Plug in. Microwave & Storage Box in Place of Passenger Seat, approx. 433,630 Miles, Engine Rebuilt in 2006 (pistons, sleeves, bearings, seals, rebuilt head). Includes 320' of 2-7/8" X 15' Drill Rod with 2-3/8" IF PinXBox (in rod box), Hoist Plug & Rod Holder Bushing, Electric Winch to Pull Stabilizer into its tray, 2" Water Hookup on both Sides of Rig, Diaphragm Pump Located on Helpers Side to Spray Down Rig, Belt Driven Hydraulic Pump Run by a Toggle Switch for Desander Pump. Replaced Mud Pump Clutch Setup in 2019, All New Plumbing and Hoses for Mud Lines in approx. 2022. Assortment of Extra Parts Available. SOLD
Water Truck - SRS #4309
DESCRIPTION: Model: Water Truck; Mounted On: 2007 Mack; Truck Engine Make: 400 HP; Condition: OFF MARKET - PUT BACK TO WORK; Tools/Options: Water Truck: 1,200 Gallon Water Bed with Grouter. 19' Long Bed. Truck has a Jake Brake, 8-Speed Low Hole Transmission, Air Ride. Welder is not Included. OFF MARKET, PUT BACK TO WORK.
Sold - SRS #4213
DESCRIPTION: Gus Pech; Model: GH48; Engine: CAT 3208; Mounted On: 1998 Volvo WG 64; Truck Engine Make: CAT 3306; Condition: SOLD; Tools/Options: Gus Pech GH48: SOLD Owner Believes the Drill is around a 1979 Year Model. 18,000# Braden Main Line, 14,000# Vickers Sandline, 48" Turn Table with a Dowmax Motor, 3-Scope Kelly Bar (approx. 68'), 8" RC Reverse Circulation Bar, 180' of Drill Pipe. Truck has approx. 52,000 Miles on it, 8-Speed Fuller Transmission with Deep Reduction (low & lo-lo), Rockwell 20,000# Front Axle and 40,000# Rears with a 4.63 Ration Full Locking Wheel Differential, Interaxle Diff. Lock, A/C. Tooling Available for an Extra Cost: 24", 30" and 36" Buckets, 24" Auger, Bucket Reamer, 18", 22", 28" and 54" RC Bits, RC Table, 8" RC Discharge Hose. Spare Parts: Bucket Teeth and Bucket Shanks (weld on), Pumps, Cylinder Parts, New Mainline Cable, Winch Parts, Valves & Valve Parts, Gus Pech Manual.
Truck - SRS #4351
DESCRIPTION: Mounted On: 2013 Freightliner Flatbed; Truck Engine Year: Cummins ISB 6.7L Diesel 220HP @2300 RPM; Condition: Ready to Work; Tools/Options: 26' Bed with Hydraulic Cathead for Pipe Handling Capabilities. Plug-ins for the Cathead are on the back of flatbed for an external power source to operate the catheads. 26,000 GVW, Automatic Transmission. Odometer Reads 116,555 Miles.
Truck - SRS #4350
DESCRIPTION: Mounted On: 2017 Talbert 25 Ton Trailer; Condition: Near New; Tools/Options: Tag-A-Long Trailer. 30' Bed, the back 25' has Gravity Tilt. Front Toolbox and Adjustable Pintle Hitch. Like New (still has factory pain on deck plates).
Rotary S - SRS #3556
DESCRIPTION: 1976, Speedstar; Model: SS-15-THH; Compressor: LeRoi 252 S2C; Mud Pump: See Below; Engine: PTO; Mounted On: CCC; Truck Engine Make: 350 Cummins; Tools/Options: 40' Mast, 3-Line Machine with an Auxiliary Line, BJ Tongs, 4-Cylinder Bean Injection Pump, Auto Oiler. A Centrifugal Mud Pump is Available, run by a Gas Engine, Set Up with PTO, Could be Mounted on Deck. Engine and Compressor have < 550 Hours on them. Carrier has a 13-Speed Transmission. Pipe and Misc. Tooling Available
Sold - SRS #4347
DESCRIPTION: Smeal; Model: 6T; Engine: 6.6 L Duramax; Mounted On: 2022 Chevy 5500 4WD; Condition: SOLD; Tools/Options: Smeal 6T : Sandline. Truck has approx. 98,000 Miles on it. Includes Generator. SOLD
Sold - SRS #4345
DESCRIPTION: Griffin; Model: 2,400 Gallon; Mounted On: 1994 Mack R-600; Truck Engine Make: 300 HP; Tires: New 24:5-11.00; Tools/Options: Griffin 2,400 Gallon Flat Tank, 21' Bed, Tailgate Comes Out, 3" and 2" Dump Valves. Had a Small Leak that has been Patched. Has a Thick Bottom. Truck has a 7-Speed Transmission.
Auger - SRS #4344
DESCRIPTION: 1983, Western Bore; Model: 100:52 HD; Engine: CAT 3208; Mounted On: 1970 Western Star; Truck Engine Make: Cummins 335; Tires: New 24-5:11.00; Condition: Runs Well; Tools/Options: Western Bore 100:52 HD Year: 1983: 100' Kelly plus has 25' and 15' Extensions. 52" Table with a Dowmax 2600 Motor, Crown, Hydraulic Dumping Arm and Kelly Kicker, 4 Outriggers, (2) H-25 Pull Master Winches. Includes 36", 24" and 18" Buckets, 60 and 160 Gallon Bailers and all Associated Tooling along with the Operating/Parts Manual for Rig & Truck. Heavy Spec Truck has a 13-Speed Transmission. Rig was Built on the Truck, Great Condition for Age.
Water Truck - SRS #4343
DESCRIPTION: Water Truck; Mounted On: 1981 Ford F-8000; Truck Engine Make: Cummins 903; Tools/Options: 3,000 Gallon Tank, Pipe Slides.
Mud Grout Pumps - SRS #4342
DESCRIPTION: Mud Pump: (2) 4X3 Centrifugal; Engine: Deutz; Mounted On: Trailer; Tools/Options: (2) 4X3 Centrifugal Mud Pumps: Trailer Mounted Home Made Mud System.
Rotary - SRS #4341
DESCRIPTION: Gardner Denver; Model: 1000; Compressor: 500/150; Mud Pump: 4X3 Mission; Engine: CAT 3208; Mounted On: 1972 Ford F8000; Truck Engine Make: CAT 3208; Tires: Needs New Tires; Tools/Options: Gardner Denver 1000: Needs New Tires. Includes 700' of 3" X 20', One 6" X 20' Collar, Drill Pipe Slips and Collar Slips..
Sold - SRS #4339
DESCRIPTION: 2011, Mud Puppy; Model: MP-255-25C; Engine: Deutz Diesel; Mounted On: Trailer; Condition: SOLD; Tools/Options: Mud Puppy MP-255-25C Year: 2011: 2,910 Hours, 1,000 Gallon Tank, Desander Pump with (4) Desander Cones, Dual 4X5 Vibrating Screening Deck. SOLD
Sold - SRS #4338
DESCRIPTION: Mud Puppy; Model: 255-400; Mounted On: Refurbished Triple Axle Trailer; Condition: SOLD; Tools/Options: Desanding Unit. Less than 500 Hours. SOLD
Sold - SRS #4337
DESCRIPTION: Pulstar; Model: P10; Engine: PTO; Mounted On: 2018 Dodge Ram 5500; Tools/Options: Pulstar P10 Year: SOLD Winch Line, Auto Wire Winder. Truck has 190,000 Miles on it, and Trailer Hitch.
Sold - SRS #4336
DESCRIPTION: GEFCO; Model: Star 40K; Compressor: Sullair 1050/350; Mud Pump: High Pressure; Engine: PTO; Mounted On: 2004 Peterbilt 357 8X4; Truck Engine Make: CAT C15; Condition: SOLD; Tools/Options: GEFCO Star 40K: 25,000# Pulldown, 40,000# Pullback, Injection Pump with Foam, Jib, 70,000 in-lbs. Maximum Torque Tophead Drive with Winch Line for Drill Pipe, Auxiliary Winch for Bailing Line, Catwalk, Driller & Helper Platforms, (5) Hydraulic Jacks, Side Platforms, 6-Pod Carousel Pipe Rack, Single Rod Loader, Pipe Spinner, Sliding Breakout Table with Hinged Section (up to 16" casing). Air Compressor was Rebuilt in 2022, Just about every Hydraulic Pump has been Replaced in the Last 3 Years. Master Cylinder Rebuilt and Ready to be Installed. Hydraulic Tank Flushed and all Filters were Changed in 2023. Truck had a New Engine put in it in 2020 and has a Jake Brake, Rear Lockers. 36K Front Tandem Axle and 46K Rears, Fuller 18-Speed Transmission, Alcoa Aluminum Wheels, (1) 100 Gallon Aluminum Fuel Tank, Two 135 Gallon Aluminum Fuel Tanks, Standard Reinforced Frame Rig can run 25' or 30' Drill Rod. Currently Set Up for 4.5" OD X 25' Rod. Capable of Carrying 600' on Board. Both 25' and 30' Rod Available for an Extra Cost. (Specs being confirmed). SOLD
Sold - SRS #4335
DESCRIPTION: GEFCO; Model: SD 300; Compressor: 850/350; Mud Pump: Centerline Duplex; Engine: PTO; Mounted On: 1998 IHC 2574 Tandem Axle; Truck Engine Make: Cummins 400 HP; Condition: SOLD; Tools/Options: GEFCO SD 300: SOLD High Pressure Mud Pump, Extra Winch for Stinger Line, Rod Loader, (2) Injection Pumps, Extra Control Circuit for Mud Pickup Pump. Compressor Rebuilt in 2022. Mud Pump not on Board but being Remounted.
Sold - SRS #4326
DESCRIPTION: approx. 6 years old, Ballard; Model: 3,200 Gallon; Mounted On: 1996 or 1998 Kenworth; Truck Engine Make: Cummins 500 HP; Condition: TEMPORARILY OFF MARKET; Tools/Options: 3,200 Gallon Water Bed approx. 6 years old, 350 Gallon Fuel Tank, 6-Ton Crane. Odometer Reads 8,027 Engine Hours and 118,810 Miles.
Sold - SRS #4334
DESCRIPTION: GEFCO; Model: SD 300; Compressor: 850/350; Mud Pump: 4X3X13 High Speed High Pressure Centrifugal 11" Impeller; Engine: PTO; Mounted On: 1998 IHC 2574; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: GEFCO SD 300: SOLD High Speed/High Pressure Centrifugal Mud Pump with an 11" Impeller.. Extra Winch for Stinger Line, Single Rod Loader, Two Injection Pumps, Foam Injection, Extra Control Circuit for Mud Pickup Pump. New/Rebuilt Motor Installed in 2020. Odometer Reads 67,630 Miles. SOLD
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |