Rigs
Steel - SRS #4490
DESCRIPTION: Drill Rod; Condition: Never Used; Tools/Options: 1,300' of 5" X 20' Drill Rod with 3.5" IF Threads, 4X4 Flats on Box End. Pipe is approx. 5-6 years old but has never been used. Was going to be used on a TH-60.
Pump Hoist - SRS #4488
DESCRIPTION: 1998, Pulstar; Model: P20; Mounted On: 1999 Ford Super Duty 2WD; Truck Engine Make: 7.3 L Diesel; Tools/Options: Pulstar P20 Year: 1998: 3-Lines, 20,000#. Truck has a 6-Speed Manual Transmission, Currently shows 300,000 Miles.
Rotary D - SRS #4486
DESCRIPTION: 1987, Driltech; Model: D25KW; Compressor: 825/350 GHH; Engine: CAT 3406; Mounted On: Ford L8000; Truck Engine Make: Ford 240 Diesel; Tools/Options: Driltech D25KW Year: 1987: CAT Deck Engine Replaced along with a Refurbished Intercooler and Head. CAT Rebuilt the Turbo in 2015. Brand New Cooler Hyd./Compressor 2016, Fuel Tank Removed, Flushed and Cleaned for Deck Engine, All Fluids and Filters Services, New Air Hoses, New Shutoff Solenoid, New Batteries, FMC Water Injection Pump, Hammer Lubricator, 6-Rod Carousel, 35,000# Pullback. Truck has a 13-Speed Road Ranger Transmission and approx. 60,000 + Miles, Engine was Overhauled in 2007.
Sold - SRS #4460
DESCRIPTION: 1998, Smeal; Model: 3T; Engine: PTO; Mounted On: 2021 Ram 4WD Single Cab; Truck Engine Make: Cummins Diesel; Tools/Options: Smeal 3T Year: 1998: SOLD Solid Unit with a Little Surface Rust. Main Line Winch and Sand Line, Remote Control for Winches. Truck has an Automatic Transmission and approx. 75,000 Miles, Near New. SOLD
Sold - SRS #4377
DESCRIPTION: 2006, Atlas Copco; Model: T3W DH 55K Pullback; Compressor: IR 1070/350 HR 2.5 with Clutch; Engine: CAT C15 565 HP; Mounted On: 2007 IHC Paystar (Navistar); Truck Engine Make: CAT C13 380 HP; Condition: SOLD; Tools/Options: Atlas Copco T3W Deephole Year: 2006: SOLD 7,600 Original Hours. 55K Pullback, Heavy Duty Reinforced High Strength Steel Double Frame Full Length of Chassis. 4 Hydraulic Outrigger Stabilizer Jacks. Over Pressure Control System on Jacks. 4 Motor, High Torque - High Speed Tophead Drive, 35' Tower with 2 Retract Positions so Hammer can be Retracted while Installing Casing, 20" Hydraulic Open & close and Swinging Open & Close Access to the Centralizer Bushings. Air Operated Table Breakout Wrench and Air Operated Retract Access Gates. Hydraulic Powered Breakout Wrench, 7-Rod Carousel set up for 4.5" Diameter Drill Pipe Table Opening, 18" Bare Drum, Single Line Hydraulically Powered Main Winch. 2-Stage Oil Flooded Screw Compressor. 1800 RPM 565 HP High Duty Cycle Industrial C15 Engine. In-Out Box Disconnect Device between Engine & Compressor. 20 GPM Water Injection with Variable Speed Control, Jib Boom for Main Winch Line with Dual Controls, Swing and Extend Capabilities, Single Rod Load & Rod Storage Box, Under Deck High Capacity Fuel Tank for Deck Engine, Under Deck Tool Box. 500' Rod Storage (25 pieces of 4.5" X 20' Cyclone Style Flush Joint Pipe) Truck Odometer Reads 3,248 Miles and 3,533 Engine Hours. Will Include some Used Drill Pipe and a Used 6" & 8" Hammer. Tophead was Replaced with a Rebuilt one by Previous Owner. SOLD
Sold - SRS #4348
DESCRIPTION: 1978, Driltech; Model: D40K; Compressor: Sullair 750/350 Rebuilt; Mud Pump: GD 5X6 Rebuilt Fluid End; Engine: CAT 3406 Rebuilt; Mounted On: CCC; Truck Engine Make: CAT 3406C - 400 HP Rebuilt; Condition: SOLD; Tools/Options: Driltech D40K Year: 1978: SOLD Dual Carousels, Rebuilt Engine Installed, approx. 1,103 Total Hours on it. Engine in Carrier has approx. 2,488 Hours Since Rebuild. Factory Rebuilt Sullair Compressor has approx. 5,415 Hours. Has a few Leaks/Drips. Includes 1,000' of 4.5" X 25' Drill Pipe and Breakout Tools. Fluid End on Mud Pump Rebuilt Last Job. Brand New Tires on Rear. Maintenance Records Available. Ready to Work !!
Sold - SRS #4270
DESCRIPTION: 2009, Schramm; Model: 450GT; Compressor: Sullair 1050/350; Mud Pump: Mission 4X3; Engine: PTO; Mounted On: Tracks; Truck Engine Make: CAT C15; Condition: SOLD; Tools/Options: Schramm 450 GT Track Drill Year: 2009: Currently has 5,047 Hours, New IDT 6" Hammer with QL Shank, Auxiliary Hydraulics, 15-Rod Carousel. Includes 375' of 3.5" X 25' Drill Rod. SOLD
Rotary S - SRS #4485
DESCRIPTION: 1979, Schramm; Model: T985; Compressor: (2) 425/250; Engine: (2) 8V71 Turbo's; Mounted On: 4-Axle CCC; Truck Engine Make: 6V53; Tools/Options: Schramm T985 Year: 1979: Fresh Paint, Two Deck Engines, Two Compressors put out 350 PSI. Rig has had Recent M&R, not much has been done to Carrier Engine. One Front Jack, Two Rear, Fuller Transmission. Includes 1,000' of Drill Rod, Hammers, Bits.
Truck - SRS #4484
DESCRIPTION: Mounted On: 1999 IHC 4WD Single Axle; Truck Engine Make: DT 466; Tools/Options: 1999 IHC 4WD Single Axle: Switched over to the Mechanical Motor and the 4WD Unit was on another Truck that they Transferred it to. Allison Automatic Transmission with PTO.
Cable - SRS #4483
DESCRIPTION: Cyclone; Model: 36; Engine: Red Seal Continental; Mounted On: 1956 Military Tandem Axle; Truck Engine Make: Chevrolet - Gas Engine; Condition: Very Good; Tools/Options: Cyclone 36: Two available, One has some New Hoses (10-15), Crown is being Redone. 3-Line Machine, Continental Engine is Powered by a 4-Speed Transmission. All 6 Hydraulic Cylinders have been Rebuilt, Mostly all New Hoses, New Hydraulic Fluid and Filters. Approx. 800' of Main Line in Very Good Condition, 36' Mast, New Paint on Rig. Ready to Work. Truck has a 4-Speed Transmission, Runs Very Good, Brakes need a Little Work, Emergency Brake Works Well. Includes Bucket, Stem, Bit and Bailer. Lots of other Tooling available for an extra cost, Jars, Bits, Stems. Auger Attachment, Stems, etc. A few Bottom Hole Assemblies also available.
Sold - SRS #4472
DESCRIPTION: 2007, Drillmax; Model: 250; Compressor: Developmental; Mud Pump: Moyno 3L6; Engine: PTO; Mounted On: Ford F550 4WD Super Duty; Truck Engine Make: Ford; Condition: SOLD; Tools/Options: Drillmax 250 Year: 2007: SOLD New Engine Installed in approx. 2024, < 1,000 Hours on it. Most Recently had been used for a backup rig. 200/100 Air Compressor, to be confirmed. Rig is set up for 2" work. Has a Pipe Rack, Single Rod Loader is Available. No Sandline.
Miscellaneous - SRS #4482
DESCRIPTION: Condition: Excellent; Tools/Options: Decompression System with Water Separator. 7.5 HP, 208 3-Phase, 50 AMP Vacuum. 16' X 10' Shed.
Rotary S - SRS #4481
DESCRIPTION: Schramm; Model: T64; Compressor: 450/250 To be Confirmed; Engine: 8V Detroit; Truck Engine Make: 6V Detroit; Tools/Options: Schramm T64: Compressor size to be confirmed. Includes 400' of Drill Rod, 8" Stabilizer, Breakout Tools.
Sold - SRS #4478
DESCRIPTION: 1988, Ingersoll Rand; Model: T3W; Compressor: 825/350; Engine: Cummins - Remanufactured; Mounted On: Ford L8000; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Ingersoll Rand T3W Year: 1988: SOLD Pipe Rack, 4 Jacks, Driller & Helper Platforms, New Compressor Cooler, Fairly New Compressor with approx. 1,000 Hours on it. Also has a Fairly New Reman Deck Engine. Rig is set up to Run 4.5" OD Drill Rod with 2-7/8" IF Connections.
Rotary D - SRS #4477
DESCRIPTION: Late 70's Early 80's, Davey; Model: M8A Roussell; Compressor: 500/125; Engine: Detroit 671 (Needs Overhauled); Mounted On: 1990's Sterling; Truck Engine Make: CAT 3306; Tools/Options: Davey M8A Roussell: Year Model is Late 70's - Early 80's. 32'6" Kelly, Mast approx. 36'. Truck is a mid 1990's. Compressor is either a Davey or LeRoi. 60-80 Gallon Water Tank. Extra Parts Available and approx. 100' of Drill Rod. Deck engine needs an Overhaul (pistons, sleaves, bearings, gaskets, new injectors).
Rotary C - SRS #4476
DESCRIPTION: 1978, Chicago Pneumatic; Model: 650 Explorer; Compressor: 900/300 to be confirmed; Engine: CAT 3406; Mounted On: 4-Axle CCC; Truck Engine Make: Cummins; Tools/Options: Chicago Pneumatic CP 650 Explorer Year: 1978: 50K Pullback. Set up to run 4.5" X 25' Drill Rod with 3.5" API Threads. Engine is good, fires right up. Air Compressor makes good air. Carousel needs some repairs. Truck Engine has a Jake Brake. Truck Run Good. It was Running Frequently until Replaced with another Drill. Includes approx. 300' of Used Drill Rod.
Water Truck - SRS #4474
DESCRIPTION: 2003, Vacuum Source Soil Vac System; Model: VT250DHD; Compressor: Removed; Engine: Kubota 4-Cylinder 59 HP; Mounted On: 1998 IHC 4700 SINGLE AXLE; Truck Engine Make: 444 Diesel; Tires: 11R22.5; Tools/Options: Vacuum Source VT 250DHD: SOIL VACUUM SYSTEM, Unit has 2,552 Hours on it. 250 Gallon Spoils Tank. Truck is a Single Axle Truck with an automatic transmission. Odometer Reads 185,693 Miles. Compressor (850 CFM @ 15 inHg) and Water Lance Removed.
Sold - SRS #4469
DESCRIPTION: 2004, Driltech; Model: D25; Compressor: 1000/350; Engine: CAT C15; Mounted On: 2004 Sterling; Truck Engine Make: Mercedes; Condition: SOLD; Tools/Options: Driltech D25 Year: 2004 SOLD Rod Box, Two Front and Two Rear Jacks. Includes approx. 600' of Driltech Drill Rod. Maintenance Records Available. 6,500 Original Hours and 46,000 Miles. SOLD
Sold - SRS #4406
DESCRIPTION: 2021, Atlas Copco EPIROC; Model: TH-60 Deephole; Compressor: 1070/350; Mud Pump: See Below; Engine: PTO; Mounted On: 2021 Peterbilt 367; Truck Engine Make: Cummins X15 600 HP; Condition: OFF MARKET - PUT TO WORK; Tools/Options: Atlas Copco TH-60 DH Year: 2021: OFF MARKET - PUT TO WORK. 36' Mast with 70K Pullback. Mud Piping with Auxiliary Hydraulic Pump to Run Offboard Mud Pump. 25 GPM Bean Pump (w/o Foam Injection), 7-Rod Carousel, 18,000# Lifting Capacity Main Hoist, Sandline Hoist, Single Rod Loader, Rod Spinner, Steel Platforms, Torque Limit Control, Dual Jib Controls, Dual Hoist Controls, 7 Gallon Electric Oiler, 3" Air Piping. Set Up to Run 4.5" X 20' Drill Rod with 2-7/8" IF Threads. 26' of Head Travel from Spindle Shoulder to the Table. 500' of 4.5" Drill Rod Available. Drill is Capable of Carrying 500' of Rod. Truck has an 18-Speed Fuller Transmission, approx. 18,117 Miles, approx. 3,236 Engine Hours and approx.. 1,784 Compressor Hours. Recently (2025) changed all the Hendrickson suspension, did a complete service and replaced the belts. Truck has 22,000# Front Axle and 46,000# Rears.
Sold - SRS #4468
DESCRIPTION: 2012, Atlas Copco; Model: T2W; Compressor: 750/300; Mud Pump: See Below; Engine: PTO; Mounted On: IHC 7600; Truck Engine Make: CAT C13; Condition: SOLD; Tools/Options: Atlas Copco T2W Year: 2012: SOLD Set up to run 4.5" Drill Rod, 9-Rod Carousel. 4X3 Centrifugal Mud Pump Mounted in the Mud Pit with is Included. Drill was not being used for mud drilling and has never run mud through it but it was tested and works fine. It has a special tophead (military), spare tophead & motor included. Truck has an Automatic Transmission. CAT engine was recently replaced and has approx. 3,200 Hours on it. Hour Meter wasn't working properly at the time shows 26,000 hours but actual hours are approx. 5,500. Mostly all the hours are air drilling. Atlas Copco Casing Hammer Available for an Extra Cost. SOLD
Sold - SRS #4446
DESCRIPTION: 1973, CME; Model: 55; Engine: 300 cid Ford Gas; Mounted On: Ardco K Buggy; Truck Engine Make: 300 cid Gas; Condition: SOLD; Tools/Options: CME 55 Year: 1973: SOLD One Winch, Cathead. Rod Rack, Auger Rack. Stout Carrier, 15,000# Gross Weight. Pulled with a Ram 3500. Tooling Available. Also has another CME 55 mounted on an Ardco Buggy available, it has (2) Winches (Pullmaster & Ramsey) SOLD
Sold - SRS #4366
DESCRIPTION: 1989, Schramm; Model: T660-H; Compressor: 900/350 GHH; Engine: 855 Cummins 450 HP; Mounted On: 2009 Mack Granite; Truck Engine Make: 485 HP; Condition: SOLD; Tools/Options: Schramm T-660H Year: 1989: SOLD Rig is Capable of Holding 280' of 4.5" Drill Rod Standing up between the Lazy Susan and Rod Rack on the Side of the Mast. 18" Table Opening. 40K Pullback, 30' of Travel as well as a Foremost Floating Sub. New Upgraded Piggyback Pump & Rotation Pump (2021), Deck Engine Completely Rebuilt in 2019, Upgraded Hydraulic Pumps, New Preheat Deck Engine Heater in 2022, Added Helpers Side Controls for Winch and Jib Boom. Compressor also rebuilt around the same time as the deck engine (2019), best guess on hours is approx. 3,000. Truck has an 18-Speed Transmission and approx. 46,345 Miles, Routine Maintenance done Yearly, New Injectors in 22/23. Includes Table Slips, Spare Rebuilt Starter for Deck Engine, New Water Pump for Deck Engine, Drive Coolers for Funk Box, New Upgraded Piggyback Hydraulic Pump for Water Injection/Rig Setup Circuit, New Braden Winch, New Hydraulic Motor for Radiator Fan, New Hydraulic Motor for CAT Pump, New hydraulic Rotation Motor Plus more Smaller Items. Complete Inventory List of Spare Parts & Items Included along with M&R Records Available. SOLD
Rotary G - SRS #4454
DESCRIPTION: Gardner Denver; Model: 1000 HD; Mud Pump: 5X6 Piston; Mounted On: 2004 IHC 7400; Truck Engine Make: International DT 530; Tools/Options: Gardner Denver 1000 HD: 4-Part Kelly Line, 3-Part Trip Line, 3-3/4" Fluted Kelly approx. 5 Years Old. Recently Installed 7-1/2" Retractable Table Rebuilt when Installed. Mud Pump Installed in approx. 2023, had a Complete Rebuild at that time. Mud Side Rebuilt once Since. Manual clutches on Drawworks and Mud Pump. Double Frame Truck, Complete Rebuild on Engine < 50 Hours ago. Brand New Clutch, and Tires < 2000 Miles Since. Eaton fuller Transmission. Walking Beam and Rear Brakes have < 1,000 Miles. Includes 380' - 400' of 3.5" Drill Rod with 2-3/8" IF Thread, No Subs..
Rotary S - SRS #4465
DESCRIPTION: 1978, Simco; Model: 5000 WS; Mud Pump: Mission 4X3 Centrifugal; Engine: Ford 300; Mounted On: 1991 GMC Topkick - Single Axle Truck; Truck Engine Make: CAT 3208; Tools/Options: Simco 5000 WS Year: 1978: Single Axle, Automatic Transmission Truck, Pipe Rack, Driller & Helper Platforms, Toolboxes, Two Rear and One Front Jack. Mud Pump Rebuilt approx. 15 Wells Ago. No Sandline, Gearmatic Model 25 Winch, 13,600# Maximum Line Pull, Hydraulic Breakout Wrench, 10" Hinged Table, Swing out Tophead to Set Casing. Includes 150' of 4.5" X 15' Aluminum Flush Rod on the Truck, Multiple Bits. More Rod Available. Truck has approx. 106,373 Miles on it.
Compressors - SRS #4464
DESCRIPTION: 2015, Doosan; Compressor: 750/175; Engine: Cummins; Mounted On: Tag Along - Pull Behind; Tools/Options: Doosan 750/175 Year: 2015 4,648 Hours.
Rotary E-F - SRS #4286
DESCRIPTION: 2018, Foremost; Model: DR 24; Compressor: IR 900/350; Mud Pump: 3X4X13; Mounted On: 2019 Kenworth 6X4 T800; Truck Engine Make: Cummins 525 HP; Condition: Good - Price Reduced; Tools/Options: Foremost DR 24 Year: 2018: Compressor has approx. 1,500 Hours and approx. 2,700 Total Hours. Includes RC Topdrive, 2-Speed with 9,6666 ft./lbs. Torque, Standard 24" Lower Drive with 83,335 ft./lbs. Torque. Auxiliary Winch with Swinging Jib (6,000# capacity), 6" Casing Jaws Installed in Lower Drive, 10" Discharge Swivel complete with 4-1/2" Cone Seal, Tool Box. Truck has an 18-Speed Transmission and approx. 22,000 Miles. Tooling Available: 1,000' of Brand New Drill Rod with 2-7/8" IF Tool Joint, 6", 8", 12" and 18" Jaws. Never used 6" Hammer, New 12" Tricone Bit, Hydraulic Welder.
Water Truck - SRS #4462
DESCRIPTION: Flatwater Fleet; Model: 1800 Gallon; Mounted On: Unmounted; Tools/Options: Flatwater Fleet 1800 Gallon: 1,800 Gallon, 18' Deck, 3,000# 1-Part Line Capacity IMT Crane PTO Operated. Brand New Bottom and Baffles (pressure tested), Wired Remote for Crane, Standard Auxiliary Fuel Tanks. Pintle Hitch, Drop Down Work Bench. Will Sandblast and Paint to Customers Color Choice. Tank was mounted on a Ford L9000 but due to the 18' deck it does fit on a shorter chassis to sit correctly.
Sold - SRS #4461
DESCRIPTION: 1993, Ingersoll Rand; Model: T3W; Compressor: IR 900/350; Engine: CAT 3406C; Mounted On: Ford L8000; Truck Engine Make: Cummins 8.3L; Condition: SOLD; Tools/Options: Ingersoll Rand T3W Year: SOLD 1993: 9-Rod Carousel, Compressor was Remanufactured in 2006, Original Compressor. Engine Replaced (reman engine) in 2019, approx. 8,000 hours since. Funk Box Rebuilt in 2022, New Rotation and Head Motors, New Feed Pump, Rebuilt Triplex Pump in 2022. 20 GPM 4-Piston Bean Pump Rebuilt recently, Oil to be Included but not Installed. Total Rig Frame Hours are approx. 15K. Rig is set up to run 3.5" Drill Rod, will include approx. 200' and a used 6" hammer. SOLD
Cable - SRS #4356
DESCRIPTION: Speedstar; Model: SS 55; Engine: Thermo King; Mounted On: 1988 IHC; Truck Engine Make: 6.9 L Diesel; Condition: PRICE REDUCED; Tools/Options: Speedstar 55: Includes Tooling with Wrenches for Drill Bar and Some Bits. Truck has an Automatic Transmission. Calipers on the Truck Need Rebuilt. Deck Engine was Rebuilt in 2009, < 100 Hours Since. Sandline Cable was also Replaced (550'), Hardly Used Since. Unit has been Stored in a Heated Shop.
Sold - SRS #4459
DESCRIPTION: 1996, Smeal ; Model: 6T; Mounted On: Unmounted; Condition: SOLD; Tools/Options: Smeal 6T: Main Line Winch and Sand Line. Remote Control for Winches. There is a Little Surface Rust on the Pump Hoist. SOLD
Rotary D - SRS #4458
DESCRIPTION: Deeprock; Model: 100; Mud Pump: 3X4X13; Engine: Perkins Diesel; Mounted On: 2004 IHC 4300; Truck Engine Make: DT 466; Condition: Ready to Drill; Tools/Options: Deeprock 100: Mission Mud Pump Rebuilt (2025). Tophead & Outrigger Cylinders are also Rebuilt. A Perkins Diesel Engine Runs the Rig and a 4-Cylinder Perkins Diesel runs the Mud Pump. Ready to Drill. Truck has approx. 198,000 Miles on it. Allison Automatic Transmission. Truck and rig are both in very good condition.
Auger - SRS #4457
DESCRIPTION: 1991, Mobile; Model: B47; Mounted On: Tandem Trailer; Truck Engine Make: 4-Cylinder Deutz; Condition: Some Rebuilds; Tools/Options: Mobile B47 Year: 1991: Cathead, Mast, 3L6 Moyno, Two Winches. Rebuilt Cylinders along with some other Rebuilds. Tool Boxes, Slide-A-Ramic Head, 4-Speed. SPT Set Up, Oil cooler, New Bushings. Hours Unknown. Fresh 4-Cylinder Diesel.
Rotary C - SRS #4452
DESCRIPTION: 1980, Chicago Pneumatic; Model: 650WS; Compressor: 825/250; Engine: 3406B REMAN; Mounted On: 1988 IHC Truck; Truck Engine Make: Cummins Big Cam 350; Condition: Well Maintained; Tools/Options: Chicago Pneumatic 650WS Year: 1980: Remanufactured Engine with approx. 2,800 Hours on it. Compressor can be turned up. Truck has approx. 93,000 Miles on it. Some Rebuilds done during previous ownership. Well Maintained, Runs Good.
Sold - SRS #4354
DESCRIPTION: Failing; Model: 1500; Mud Pump: 4.5" X 5" Gardner Denver; Engine: DT466B; Mounted On: 1981 IHC; Condition: Ready to Drill; Tools/Options: Failing 1500: 2-7/8" X 20' Kelly. Set up to Run 20' Drill Pipe. Retractable Table, Sandline, 35' Mast. Includes 400' of Drill Rod. Tooling available for an extra cost.
Sold - SRS #4455
DESCRIPTION: 2014, Hunke; Model: 4THRGPP; Engine: PTO; Mounted On: 2014 Ford F-350 4WD; Truck Engine Make: 6.7L Diesel; Tires: 17"; Condition: SOLD; Tools/Options: Hunke 4THRGPP Year: 2014: 9' Omaha Utility Bed, Remote Hookup, Outriggers, Pipe Racks. Odometer Reads 4,818 Miles, Manual Transmission. Only 215 Total Hours. SOLD
Sold - SRS #4365
DESCRIPTION: 1999, Ingersoll Rand; Model: T3; Compressor: 900/350 (BRAND NEW DOOSAN); Engine: CAT 3406 (Rebuilt in May 2022); Mounted On: 2005 Kenworth T-800; Truck Engine Make: Cummins ISX 565 HP; Condition: SOLD; Tools/Options: Ingersoll Rand T3 Year: 1999 SOLD Deck Engine rebuilt in May 2022. Brand New Doosan Compressor was Installed at the same time with a 5 Year Warranty. Approx. 950 Hours on both at this time. Rotation Head Completely Rebuilt in April 2024 as well as most Hydraulic Pumps. Set Up to Run 3.5" Drill Rod. Rig has an 11" Table Opening, 34' Mast (from bottom to top of the jib). Truck has 212,000 Frame Miles but has a Brand New Cummins Engine with only approx. 18,500 Miles on it, also has an 18-Speed Transmission. M&R Records Available. SOLD
Sold - SRS #4399
DESCRIPTION: 1981, Midway ; Model: 1500; Compressor: LeRoi 256 SDS; Mud Pump: Gardner Denver 5-1/2" X 8"; Engine: PTO; Mounted On: 2014 Kenworth T-800; Truck Engine Make: Cummins 600 HP; Condition: SOLD; Tools/Options: Midway 1500 Year: 1981: SOLD Low Hours and Miles, 8-1/2" Retractable Table, 38' Derrick with an 18' Mast Extension (56' with extension). 3-3/4" X 23' Kelly, 2" Little Giant Swivel, Compressor Disconnect Clutch, Standard Size Pulldown Chains, (4) Leveling Jacks, No Carousel. Large Rod Rack that Holds Approx. 800' of Drill Rod. Rig Runs 3-1/2" Drill Rod. New Mast Cylinder, New Hoses (air & hydraulic), New Piping. Odometer Currently Reads 288 Miles and 36.4 Hours, Full Lockers and 46,000# Rear Ends.
Sold - SRS #4023
DESCRIPTION: 1981, Speedstar; Model: SS-40; Mud Pump: 7.5" X 10"; Engine: 6V71NA Detroit; Mounted On: 8X4 CCC; Truck Engine Make: 8V71 Detroit; Condition: SOLD; Tools/Options: Speedstar SS-40 Year: 1981: SOLD Double Drum Drawworks, Sandline Drum, Air Clutches, Catheads, Hydromatic Brake System, 4 Hydraulic Leveling Jacks, Under-Drive Air Clutch for Mud Pump Installation, King 50KG Mud Swivel, Allison Automatic Transmission, Hydraulically Raised 60' Derrick, (2) McKissick 3-Sheave Traveling Blocks, Kelly Bar, Derrick Night Lights, Speedstar 18" Rotary Table. Rear Hinged Rig Floor Platform, 4" Derrick Standpipe, 2" Mud Mixing Valve at Pump & 4" Ball Valve on Back Side of Mud Mixing Valve. Rebuilt Hydraulic Cylinders Including Outriggers, Derrick Raising and Tong Cylinders. Hydraulic Hoses on Derrick Raising Cylinders & all Outrigger Cylinders were replaced approx. 2 Years Ago. New Clutches, Recently Sandblasted, 2023, (currently being painted). Recent work includes Rebuilt Mud Pump (fluid end, clutches, belts), Rebuilt Deck Engine, New Brakes, Drums, Shoes on Carrier, Good Tires. Still needs Mud Lines, Gauges and Wiring. SOLD
Sold - SRS #4453
DESCRIPTION: 2004, CME; Model: 75; Mud Pump: Plumbed, Mud Pump Available; Engine: Cummins 6BT; Mounted On: 2004 IHC 7400 Tandem; Truck Engine Make: DT 466E; Condition: SOLD; Tools/Options: CME 75 Year: 2004: SOLD One Owner Drill. 5-Speed Transmission, 3 Pump Hydraulic system, Tandem Gear Pump and One Variable Displacement Pump Dedicated for the Moyno. 25' Mast from Base Frame (angle drill spec), High Speed Head, In/out Side to Side Slide Base, Fluted Kelly with Quick Disconnect, Hydraulic Chuck (2-5/8"), 8,500# Main Winch, 3,200# Auxiliary Winch, 1,800# Auxiliary Winch, Fast Wireline Winch, 140/300# Auto Hammer, 4-1/2" Hydraulic Rod Holder and Breakout Wrench, Hydraulic Underside Slide Out, Auger/Casing Rack Under Water Tank Storage, Two Level Rod Rack for 10' Rod. Will have a Moyno 3L8 Pump, (Gardner Denver mud pump available for extra cost), 2" Mud Discharge Plumbing Under Deck, 3" Suction & Freshwater Plumbing, 900' Gallon Stainless Water Tank. Approx.16,920 Total Rig Hours, Truck has approx.105,300 Miles, Allison MD 3060 Automatic Transmission, Double Frame, 20K Rears, 14K Front Axle, 20,000# Front Winch. Good Rear 11R22.5, Front 385/65R22.5. Current Owner was Drilling Geotechnical, Mud Rotary, Rock Coring. No Tooling Available. SOLD
Sold - SRS #4397
DESCRIPTION: 1989, Speedstar; Model: Mini Star; Compressor: Sullair Developmental; Mud Pump: Centrifugal; Engine: John Deere; Mounted On: 2013 IHC 7300 4WD; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Speedstar Mini Star Year: 1989: SOLD 12K Pullback & Pulldown, 4K Winch, Driller & Helper Platforms, Rod Box. Single Rod Loader, Tophead was Recently Rebuilt, all New Seals and Bearings, Mud Pump only a few Years Old. Deck Engine has New Exhaust Manifold & New Injectors. Truck has 57,000 Miles on it. Truck is Like New. Rig was Recently Painted. Includes 400' of 2-3/8" IF X 20' Mayhew Jr Drill Rod, Near New, 20' Stabilizer, Hoisting Plug. SOLD
Rotary P-Q - SRS #4440
DESCRIPTION: Portadrill; Model: 10TE59; Mud Pump: See Below; Engine: 6-71 Detroit; Mounted On: 1994 IHC Paystar 5000; Truck Engine Make: L10 Cummins; Condition: Ready to Drill PRICE REDUCTION; Tools/Options: Portadrill 10TE59: BIG PRICE REDUCTION!! 55' Mast, Portadrill Swivel 2-1/2" Opening, 4-1/4" X 35.10' Kelly, 8" Retractable Portadrill Rotary Table. Includes H-25 Bethlehem 7-1/4" X 12" Mud Pump Powered by a 350 Cummins. 1,950' of 3.5" Drill Pipe with Breakout Flats, (2) 30' Drill Collars, misc. Subs & Bits. Pipe Tub for Drill Pipe and Misc. Items, Doghouse (old school bus with 366 gas engine, auto transmission), Hydraulic Unit 2-71 Detroit Power, Hydraulic Power Tongs 2-3/8" X 4-1/2" Casing, Small Kelly for Working Inside 4-1/2" Casing.
Water Truck - SRS #4451
DESCRIPTION: Ballard; Model: 2,000; Mounted On: 1996 Ford; Truck Engine Make: Detroit 370 HP 60 Series; Tools/Options: Ballard 2,000 Gallon Tank. Tank Leaks a few Gallons/minute. 60 Series Engine has 42,000 Miles on it, Eaton 10-Speed Transmission, 52,000# GVW. 18'8" Bed, 21' Overall
Auger - SRS #4450
DESCRIPTION: 2014, CME; Model: 850X; Engine: PTO; Mounted On: Tracks; Truck Engine Make: Cummins QSB 6.7L; Tools/Options: CME 850X Year: 2014: High Speed Rotation, CPT Controls, Work Tables, Cathead, In/Out Slide Base, Auto Hammer, Breakout Wrench, Moyno Pump. 8,500#, 3,200#, 1,800# Hydraulic Hoists, Hydraulic Wireline Hoist with 1,800# Pull. Auger & Rod Guides for Angle Drilling, Water Swivel, Fluted Kelly and Chuck Assembly, Spindle Adapter, Moyno 36 GPM & a Moyno 84 GPM Water Pumps. Additional Tool Storage Compartments, Continuous Sample Tube System. Turbocharged and Air Cooled 6-Cylinder Tier 4 Diesel Engine. 195 HP Driving and 117 HP Drilling both @ 2,300 rpm. 25,800# Maximum Track Force, Zero Turn. 20,000# Hydraulic Front Winch. 5-Speed Forward Rotary Transmission, 15,410 ft. lbs. Maximum Rotary Torque, 670 Maximum rpm Rotary Speed. 28,275# Retract Force3, 18,650# Pulldown Force, 90'/min. Retract Rate (max) and 55'.min. Feed Rate (max), 72" (6') Stroke. Rod & Tooling Available for Extra Money. Was being used for Geo-Tech Drilling, Mud Rotary, Air Rotary, Auger Drilling.
Sold - SRS #4374
DESCRIPTION: 1989, Reichdrill; Model: T-650-W; Compressor: 900/350 GHH; Engine: CAT 3406B; Mounted On: 1989 Mack DM 690 6X4; Truck Engine Make: Mack 300 +; Condition: SOLD; Tools/Options: Reichdrill T-650-W Year: 1989: SOLD CAT 3406B Rebuilt from Crank Up, approx. 600 Hours Since. Compressor was also Rebuilt approx. 500 Hours Ago. Deck Engine Rated at 400 HP @ 1800 RPM, Twin Screw, 2-Stage Air Compressor. Auto Indexing, Air Pressure Regulator, 20 GPM Water Injection, Electric Air Line Lubricator, Vandal Cover, Operator & Helpers Platforms, Helpers Walkway. New Style Loader, New Style Tyrell Head, 15 Piece Pipe Rack, Hammer Holder, Stabilizer Holder, Torque Control, Spare Stacker Section. Includes 600' of 4.5" X 20' Reichdrill Style Drill Rod with 3.5" API Connections, Pipe Sling, J wrench, Petol Breakout Wrench, Table Bushings, New 6" Hammer. Truck has 48,000 Original Miles. Total Rig hours are 11,600. Parked during winter months, average of 300 - 400 Hours per year during current ownership. Purchased it with approx. 5,500 hours. SOLD
Rotary T-Z - SRS #4161
DESCRIPTION: 2003, Versa-Drill; Model: V-2000; Compressor: 1070/350; Mud Pump: Has hydraulics for one; Engine: PTO; Mounted On: Kimble 4WD; Truck Engine Make: CAT C16; Condition: PRICE REDUCED; Tools/Options: Versa Drill V-2000 Year: 2003: 80K Pullback, Tophead has all New Bearings and Seals. Rod Handling System that can carry 500' of Drill Pipe. It has Power Beyond for 3X4 Mud Pump. New Starter and New Clutch Installed February 2023. Newer Tires on the Front & Rear, New Tophead Drive Motors Installed in 2023. Rebuilt Rotary, Main Winch, 4 Rear Pumps (included but not installed), Walking Beam Suspension. Front End Gone Through, Some Hoses Replaced, New Fluids.
Sold - SRS #4449
DESCRIPTION: 1996, Driltech; Model: DK25; Compressor: 900/350; Engine: CAT 3406B; Mounted On: 1996 Ford L8000; Truck Engine Make: Diesel; Condition: NOT AVAILABLE; Tools/Options: Driltech DK25 Year: 1996: Deck Engine ECM and Top End Rebuilt in 2022. Compressor Rebuilt in 2018, Hours Unavailable, Gauge isn't Working (last reading showed 9,440 Engine Hours). (4) Jacks, 2 Front and 2 Rear, Rod Box. New 24 GPM 4-Cylinder Bean Water Injection Pump Lots of Spare Parts Including Rotation Pumps, Seal Kits and Tooling. Small Welder on Deck. Odometer Currently Reads 77,496. NOT AVAILABLE
Sold - SRS #4445
DESCRIPTION: 1973, Acker; Model: AD II; Engine: 300 cid Ford Gas; Mounted On: 1990 Ford F-800; Truck Engine Make: 429 Gas; Condition: SOLD; Tools/Options: Acker AD II Year: 1973: 3L6 Moyno, Two Winches and Cathead. No Leaks. Truck has New Tires & Brakes. Tooling Available. SOLD
Rotary G - SRS #4443
DESCRIPTION: 1990, Gill Beetle; Mounted On: Tracks; Tools/Options: Gill Beetle Year: 1990: Tophead Drive. Includes 200' of Aluminum Drill Rod and 100' of Steel Drill Rod. Carousel holds 6 Rods. IR Side Air Available for an extra cost.
Rotary G - SRS #4442
DESCRIPTION: Geo Drill; Compressor: 900/350 Sullair; Mounted On: 2005 Sterling; Tools/Options: Geo Drill: 15-Rod Carousel. Includes 300' of 20' 3.5" Regular Drill Rod.
Rotary S - SRS #4441
DESCRIPTION: 1977, Speedstar; Model: SS-15; Compressor: LeRoi 600/250; Engine: PTO; Mounted On: CCC; Tools/Options: Speedstar SS-15 Year: 1977: Tophead Drive, 43' Mast, Manual Clutches. One Front Jack and Two Rear Jacks, Driller/Helper Platforms. Includes 300' of Drill Rod, Tiger Tierra Casing Hammer Available for an Extra Cost. Approx. 400,000 Miles. No Hour Meter.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |