Rigs
Rotary H-I - SRS #4559
DESCRIPTION: 1996, Ingersoll Rand; Model: T2W; Compressor: 750/300 IR Screw; Mud Pump: 3X4X13; Engine: PTO; Mounted On: 1995 IHC 2674 6X4; Truck Engine Make: Cummins N14 370 HP; Condition: Working Daily; Tools/Options: Ingersoll Rand T2W Year: 1996: 4 Digit Hour Meter Shows 4,341 Hours ? 30,000# Pulldown and 30,000# Pullback, 18 GPM Bean Pump, DHD Injection Oiler. Dual Motor Tophead, Black Top Cummins Engine in Truck, has a Spicer 10-Speed Transmission, 47,999 GVWR and 451,085 Miles. Set up to run 2-3/8" FEDP Rod, 4.5" Carousel is available. Seals were done in the PTO, Top End in Engine was Redone < 1,000 Hrs. ago along with some other M&R work. Drill Rod Available..
Rotary S - SRS #4558
DESCRIPTION: Seismic; Model: Mud & Air Drill; Compressor: GD 680; Mud Pump: GD 5X6 (Belt Driven); Engine: PTO; Mounted On: 2007 Kenworth; Truck Engine Make: CAT (big one); Condition: Great; Tools/Options: Seismic Mud Drill. Current owner had it down to 500', Mud Drilling. Mast is longer than the standard mast, approx. 34', Mud Pump is Belt Driven and has its own Clutches (can shut off when running air compressor). Has a New Table (same as a Badger, has a Quill that can be removed). Has been Re-decked and repainted. Runs 2-7.8" O.D. Drill Rod with Mayhew Regular Thread. Odometer Reads 3,928 Miles (drilling), 46K Rears, 20K Front Axle Full Lockers, Double Frame, Pre-emission CAT Engine (big one), Spicer Gearbox (new), Pro Heat. Mud Pan Included
Auger - SRS #4557
DESCRIPTION: 2025, Mobile ; Model: B-25; Mud Pump: None; Engine: PTO; Mounted On: Raymar TRK60S Rubber Tracks; Truck Engine Make: 44 HP Kubota Turbo Diesel; Condition: Never Used; Tools/Options: Mobile B-25 Year: 2025, 4-Speed Rotary Head, 76" Single Cylinder Feed System, Auger/Tool Guide Support, Triple Hydraulic Pump, All Controls Located in Control Panel, Emergency Shut Down, 1-5/8" Hex Safety Auger Coupling, Front Mounted Auger. 140# Auto SPT Hammer, NWJ Hammer Rod Pin. 4,500# Auxiliary Hoist, 3,000# Auxiliary Hoist, 18' Mast, Shelby Tube Sampler Extruder (3" X 30") Mounted on Helper Side, Fold Down 18" X 18" Fold Down Work Table, Breakout Accessories - Single Jaw Rod Clamp & 24" Cylinder Mounted Breakout Wrench, Tool Box, 5' Rod Rack, (4) 24" Hydraulic Leveling Jacks. NWJ Thread Connection, 3-1/4" 2K Standard Auger Connection. Rubber Tracks: OAL 74.3" Long, 9" Wide Tracks. Hydraulically Powered Planetary Drive with Internal Brakes, Wireless Remote Control & Manual Controls Mounted on Carrier, 20 Gallon Fuel Tank. Never Used. Includes a 2025 2 Axle, 22' Trailer.
Pump Hoist - SRS #4520
DESCRIPTION: 2008, Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F450 4WD; Truck Engine Make: Diesel; Condition: Working Unit; Tools/Options: Smeal 5T Year: 2008: Manual Transmission, Sandline, Remote. Bed has some rust on it. Odometer Reads 164,481. MOTIVATED SELLER
Pump Hoist - SRS #4489
DESCRIPTION: Reichdrill; Model: Eagle; Mounted On: GMC 5500 4X4; Truck Engine Make: Duramax Diesel; Condition: OFF MARKET BEING USED; Tools/Options: Reichdrill Eagle: Three Line Machine, 6,000# Single Line, Allison Automatic Transmission.
Rotary R - SRS #4363
DESCRIPTION: 2023, Reichdrill; Model: RTD 69; Compressor: 1070/375; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: X15 605 HP; Condition: PRICE REDUCED !!; Tools/Options: Reichdrill RTD 69 Year: 2023: Price Reduced. 43,980# Pullback, 160 HS Chain, 35,000# Pulldown, 140 HS Chain, REGEN, Air Operated Holding Wrench with Hydraulic Raising/Lowering, 7-Pod Carousel for 4" X 20' Drill Rod, 8-Gallon Air Line Lubricator, Multicore Cooler, Thermostat Controlled Fan Circuit for Improved Cooling and Fuel Savings, 34' Mast with 28' Stroke, 22" Table Opening, Dual Winches (8,500#), Hydraulically Extendable Jib, Wireless Radio Helper's Remote Controls for Jib Swing, Extend & Retract, Carousel Index/Lock, Winch Up and 2-Speed Winch Down, 20 GPM Water Injection Pump, Torque Limiter Control, Holdback Control, Feed Override all with bypass on & off. Mudline Stand Pipe with Hose Spud & End Cap, Cribbing Rack, 4 Leveling Jacks(36" & 48"), 18 Piece Rod Box, Drill Pipe Lifting Rod, Two Hammer Holders (7" & 10"), Diverter, Hydraulic Welder, Set Up to Run 4" Drill Rod. Capable of Holding 600' of Rod per Owner. Toolbox, Folding Rear Platforms Vandal Cover, Halogen Night Lighting. Truck has an 18-Speed Transmission, Differential Lock, 20K Steerable Lift Axle, Bluetooth, A/C, Heated Mirrors, Aluminum Wheels, Dual 80 Gallon Fuel Tanks, DEF Tank. Includes 1,000' of Rod. Stabilizer holder for the carousel is available but isn't on the rig, taken off to hold 2 more rods. Approx. 601 Hours and 2,100 Miles.. Condition: Near New
Rotary D - SRS #4552
DESCRIPTION: 2007, Driltech; Model: T25; Compressor: 1150/350; Engine: CAT C15; Mounted On: 2007 Sterling; Truck Engine Make: Mercedes; Tools/Options: Driltech T25 Year: 2007: Approx. 9,000 Original Hours, approx. 4,500 Compressor Hours. Driller & Operators Platforms, Two Rear Jacks and Two Behind the Cab, Rod Rack, Toolbox, Hammer Holder, Carousel. Includes 900' of 4.5" Drill Rod, Bits, Stabilizer. Also includes a 2,000 Gallon Sterling Water Truck with 20' Bed. Rig can be sold separately also.
Rotary D - SRS #4551
DESCRIPTION: 2007, Driltech; Model: T25; Compressor: 1050/350; Engine: CAT C15; Mounted On: 2007 Sterling; Truck Engine Make: CAT C13; Tires: New; Tools/Options: Driltech T25 Year: 2007: Truck has 52,000 Miles on it, 7,800 Total Rig Hours, 1,800 Hours on Reman CAT C15, Rebuilt Compressor, New Air Intakes, New Mesabi Cooler Package, All New Hoses (Compressor and Hydraulic), all 3 Pumps Rebuilt, New Bearings in Funk Box, New Winch Cable, Rebuilt Bean Pump, New Tool Box, Rebuilt 2 Lower Spools, Rig and Truck Painted. Many other Repairs have been done, Head was Rebuilt and Pullback Cylinder Rebuilt 18 Months ago. Includes 400' of 4.5" Drill Rod. Available for an extra cost: New Chains, Sprockets & Pins, Rebuilt Head and Water Swivel, Rebuilt Pullback cylinder.
Rotary S - SRS #4555
DESCRIPTION: 1978, Gardner Denver ; Model: 1500; Compressor: 667 2-Stage; Mud Pump: 5-1/2" X 8" FLUID END AND POWER END (2026) RECENTLY REBUILT; Mounted On: 1978 Ford L9000; Truck Engine Make: CAT 3208; Tools/Options: Gardner Denver 1500 Year: 1978: 10" Sliding Rotary Table, Manual Clutches, Triple Line Kelly and Sandline, 24; Kelly, Rig is set up to run 3.5" X 15' Pipe and has a 15' Rod Box, 4 Leveling Jacks (one recently repacked 2026). Master Cylinder on Driller side has been Repacked, Pinion Bearings in Rotary Table Replaced (2026). Truck has a 13-Speed Transmission and Engine has a New Water Pump and Belts. Will Include what pipe is on it, 345' of 3.5" Drill Pipe. More pipe and stabilizers available for an extra cost.
Rotary A-B - SRS #4554
DESCRIPTION: 2008, Atlas Copco; Model: TH-60; Compressor: 900 HR.2; Mud Pump: Plumbed; Engine: PTO; Mounted On: Peterbilt Tri Drive; Truck Engine Make: 600 HP Cummins ISX; Tires: New; Condition: Spare Drill; Tools/Options: Atlas Copco TH-60 Year: 2008: New Fabco 172 Transfer Case, New Tires, Front & Rear. Completely New Fully Rebuilt Engine (2017 - Borg Warner parts) with approx. 2,600 Hours on it. New Hydraulic Cooler in 2021, Truck has approx. 10,000 Hours and < 124,500 Miles. Drill has approx. 6,200 Hours and approx. 2,470 Compressor Hour. Fleet Maintained, Service Records Available and hasn't been used in 5 years as it was a spare drill. Rod Rack is included. Rig is Plumbed for a Centerline Mud Pump. 7X10 Aluminum Centerline duplex mud pump is available for an extra cost. Rig is set up to run 3.5" Drill Pipe.
Auger - SRS #4550
DESCRIPTION: Diedrich; Model: D-120; Mud Pump: SP-50; Mounted On: 2003 ATV with Rubber Tires; Truck Engine Make: John Deere 6.8 L; Tools/Options: Diedrich D120: Rig had every option available at the time of purchase. Original Owner.
Rotary S - SRS #4549
DESCRIPTION: 1985, Speedstar; Model: 985; Compressor: Removed; Mud Pump: 5X4 Centrifugal; Engine: Detroit 8V92; Mounted On: 4-Axle CCC; Truck Engine Make: Detroit; Tools/Options: Speedstar 985 Year: 1985: 70K Rope Head Drive, Tophead Retracts. Includes 500' of 4.5" Bottleneck Drill Pipe. Drill had and air compressor on it prior to current owners ownership. Table opening is at least 28" plus a bushing Insert that will close it up to approx. 15". Mast is about 42' (to be confirmed). Rotary Head, 60K Winch Line, Swinging Jib with Winch. Detroit Engine under the hood with a Power Tower.
Rotary E-F - SRS #4548
DESCRIPTION: Failing; Model: 314C; Mud Pump: Gardner Denver 5X6; Mounted On: 1984 Ford F700; Truck Engine Make: 370 - 429 V8 Gas; Tires: Hold Air but Older; Condition: Good - Working; Tools/Options: Failing 314C: Includes some bits and attachments. Truck Engine has a 5-Speed Transmission, 2-Speed Rear Axles Runs & Drives. Rig has a Main Winch and it also has a Sandline Winch. Table size looks to be 3-3/4" and it runs either N3 or N4 Drill Pipe. Everything works as it is supposed to, needs a little TLC to make it perfect. Truck will need some brake work and rig will need drop pipes. Tire hold air but are old (+/- 10 years old).
Sold - SRS #4497
DESCRIPTION: 1983, Bucyrus Erie; Model: 22W Series III; Engine: 3-Cylinder Deutz Diesel; Mounted On: 1990 IHC; Truck Engine Make: Diesel; Tires: Good; Condition: SOLD; Tools/Options: Bucyrus Erie 22W Series III Year: 1983: approx. 700' of 3.4" Drill Line and approx. 700' of 3/8" Sandline, Hydraulic Jacks. 2025 Had a Brand New Shaft Installed along with New Bushings and Hoisting Gear. Includes a set of wrenches, tooled up. Truck has approx. 25,000 Miles on it. SOLD
Rotary E-F - SRS #4471
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6; Engine: PTO; Mounted On: 1990 IHC; Truck Engine Make: DT 466; Condition: PRICE REDUCED; Tools/Options: Failing 1500: OPEN TO OFFERS! Retractable Drawworks, Heavy Duty Mast, Fabricated Table (can remove top plate to install surface casing), No Kelly Included, 42' Mast, Set up to Run 2-7/8" External Upset Drill Pipe with Lugs, Four Jacks. Truck has 188,419 Miles on it. Drill Rod, Slips to fit table and Two Older Parts Rigs Available for an Extra Cost.
Rotary E-F - SRS #4470
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6 with Air Clutch; Engine: PTO; Mounted On: 2006 Freightliner; Truck Engine Make: CAT C7; Condition: PRICE REDUCED; Tools/Options: Failing 1500: PRICE REDUCED! Fluid End on Mud Pump Needs New Liners and Pistons. Newly remanufactured Drawworks, All Retractable, Heavy Duty Mast, Heavy Duty Mechanical Breakout Table - Chain is Broken -Assembly C2201-D, 2-7/8" X 27' Long Kelly, 42' Mast, Sandline with 1/2" Cable. Rig is Set up to run 2-7/8" External Upset Drill Pipe with Lugs. Front and Rear Jacks, Operators Platform, Pipe Rack. Approx. 344,193 Miles on Truck. Drill Rod, Slips and Two Older Parts Rigs Available for an Extra Cost.
Miscellaneous - SRS #4547
DESCRIPTION: Engine: 2015 Cummins QSX15, 525 HP California Carb Compliant Engine; Mounted On: Trailer; Tools/Options: Engine odometer reads 900 hours.
Rotary E-F - SRS #4546
DESCRIPTION: 2012, Foremost; Model: DR 12/26P-60/24-900 DR24HD; Compressor: IR 900/350; Engine: PTO; Mounted On: Kenworth T800W; Truck Engine Make: Cummins ISXZ 525 HP; Tools/Options: Foremost DR 12/26P-60/24-900 Year 2012: DR 24HD, 80,000# Pullback with Upgraded 6" Cylinders and Mast Structure Reinforcement. Upgraded RC 150 High Torque, Topdrive 12,000 ft.-lbs., Auxiliary Winch with Swinging Jib, Line Oiler, 12 GPM CAT Water Injection, Drill is set up to run 4.5" reg drill rod. Lower Drive Upgraded to 1.4 Million in./lb. (originally 1 million in./lbs.) Tier 4 Engine, Jake Brake, Upgraded Cooling Package, 20K Front and 46K Rears. Torque Lower drive has been gone through and what needed rebuilt was, Tophead has also been rebuilt. New Hydraulic Pumps and Hoses, Plates in Lower Drive were Rebuilt. New Turbo on Truck Engine. $100K in recent M&R Includes 6" to 24" Jaws, Big 16" Diverter.
Pump Hoist - SRS #4545
DESCRIPTION: Smeal; Model: 4T; Engine: PTO; Mounted On: 2014 Ram 4500 2WD; Truck Engine Make: Hemi Gasoline; Tools/Options: Smeal 4T: Truck has an Automatic Transmission.
Pump Hoist - SRS #4544
DESCRIPTION: Smeal; Model: 10T; Engine: PTO; Mounted On: 1994 Ford F750; Truck Engine Make: Cummins 230 HP; Tools/Options: Smeal 12T Year 1979: Truck has Air Brakes & a 5-Speed. 36' Mast, 8' Layback at 36'
Pump Hoist - SRS #4543
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 2007 Ford F450 4WD; Truck Engine Make: 6.0 L Power stroke Diesel; Tools/Options: Smeal 5T: No Sandline, has the Plug for a Remote. Truck has a Power stroke Diesel and Automatic Transmission, approx. 66,000 Miles on it. Tailgate and Pipe Racks being put back on.
Rotary D - SRS #4542
DESCRIPTION: 1983, Dresser; Model: T70W; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: CAT 3406; Tools/Options: Dresser T70W Year: 1983: 70K Pullback, Tophead Drive. Runs Range II Pipe, Rod Loader (can preload pipe), 12" Hydraulic Table (hydraulic, hinges up & dies are interchangeable), 4 Drums, 3 Winch Lines. Capable of Retrieving Core Barrels. One Front and Two Rear Jacks. Crane Carrier has some Rust. Had a CAT 4 Mast Inspection in 2014.
Rotary E-F - SRS #3836
DESCRIPTION: 2004, Foremost; Model: DR-24 HD; Compressor: 1070/350; Engine: PTO; Mounted On: 2003 Kenworth Tri-Drive; Truck Engine Make: Cummins 565 HP; Tires: Newer; Condition: Working Drill; Tools/Options: Foremost DR24HD Year 2004: approx. 2,800 Compressor Hours and approx. 9,300 Rig Hours. Gear Driven Lower Drive Casing Rotator. Dual High Torque Tophead, Bean Injection Pump, Hammer Oiler. Work done within 750 Hours: All New Flow Hoses to 3", New Fabco PTO Boxes with Coolers, New Mast Hoist cylinder, Two new Front Tires & 4 New Rear Drives, Full Top End of Motor Redone - head, injectors, Fuel Pump, Fuel Lines, Injection Pump, Turbo, All New Exhaust, Mufflers & Tips. Includes: All Wrenches & Plates, Cyclone with Hoses, 6", 8", 10", 12", 16", 20" and 24" Jaws, 10" Discharge Swivel with Adapters, Spare Sub for 2-7/8" Thread, Full Tophead Seal Kit. Truck has 42,000 Miles on it.
Rotary G - SRS #4393
DESCRIPTION: 2018/19, GEFCO; Model: 40K; Compressor: Sullair 1000/350; Mud Pump: Plumbed; Engine: PTO; Mounted On: 2019 Peterbilt 367 6X4; Truck Engine Make: Cummins 565 HP (recently rebuilt); Condition: Good Working Drill; Tools/Options: GEFCO 40K Year: 2019: Newly Rebuilt Engine (Injectors, Turbo, Oil Cooler), Truck Brake Compressor also Rebuilt. Rig is set up to Run 4.5" X 20' Flush Joint Drill Pipe with 2-7/8" IF Tool Joints and a Holte 350 Casing Hammer. 25K Pulldown, 40K Pullback. 18 GPM Bean Water Injection, 7-Gallon Electric Downhole Lubricator, 25,000# Single Line Hydraulic Main Winch over the Jib. Hydraulic Rod Spinner, Modified 60" Breakout Wrench, Auxiliary Winch Mount & Hydraulics (rig has 2 winches, cable recently replaced), 3-Speed Tophead, 15 Piece Rod Box, 6-Rod Carousel, Hammer Holder. Upgraded Joysticks (5-Volt Electric Upgrade), Compressor has approx. 2,300 Hours, approx. 6,000 Total Frame Hours, < 500 Hours on the Newly Rebuilt Engine.. Truck has 22,000# Front Axle, 46,000# Rears, 18-Speed Fuller Transmission. 400' of used pipe included.. Condition: Working Drill
Sold - SRS #4448
DESCRIPTION: 2008, Flatwater Fleet; Model: 2,700 Gallon ; Mounted On: 2006 IHC 7400; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Flatwater Fleet 2,700 Gallon Year: 2008: SOLD (2) 110 Gallon Transfer Fuel Tanks all Redone and Painted. 20' Bed Space with Tool Boxes & Fuel Tanks in the Front, 2'6" Tall. Two Brand New Boxes on the Front and Two on the Back in 2024 and Repainted Box, New Lights on the Back with New Brackets, all Maintenance that was needed was also done at that time. Odometer Currently Reads 172,587 Miles, Allison Automatic Transmission (installed a few years ago), low miles on it. Truck is Kept Indoors. SOLD
Sold - SRS #4332
DESCRIPTION: 2008, GEFCO; Model: 30K; Compressor: 1000/350 Screw, Heavy Duty PTO with Clutch; Mud Pump: 4X3 Mission NEW; Engine: PTO; Mounted On: 2008 Peterbilt 367 6X4; Truck Engine Make: CAT C15 550 HP; Tires: New - Front; Condition: SOLD; Tools/Options: GEFCO 30K Year: 2008: SOLD Hydraulically Driven Mud Pump with Standard 2-1/2" Piping. (4) Hydraulic Leveling Jacks, Tophead Drive with 70,000 in-lb. Torque, 0-120 RPM, 2-11/16" Water/Air Course, Hydraulic Jib Boom with Dual Controls on Driller & Helper Side. Carousel Holds (6) Pieces of 4.5" X 20' Drill Rod, 2-7/8" IF Tool Joints with Top Breakout Wrench. Hydraulic Cylinder with Cable Pulldown Holdback. 25,000# Pulldown and 30,000# Pullback. Man Winch over Jib Boom, 25,000# Single Line Pull with 3/4" Cable. Line Oiler, 18 GPM Bean 4-Cylnder Hydraulic Powered Water Injection Pump. Single Rod Loader, Helpers Side for Loading Rod under Tophead, Hydraulically Powered Split Table Guide with Air Operated Holding Wrench, Hydraulically Powered 60" Breakout Wrench, Hydraulically Powered Rod Spinner. PL2 Auxiliary Winch with 100' of 3/8" Cable (2,000# capacity), Pipe Rack for 15 Pieces of 4.5" X 20 Drill Rod (slide on outside of pipe rack), (5) Operating Lights, Heavy Duty PTO for Compressor and Hydraulic Pump Drive with Clutch. Side Driller and Helpers Platforms. Truck has 22,000# Front Axle and 46,000# Rears, Fuller 18-Speed Transmission, (2) Fuel Tanks (70 & 150 Gallon), A/C, Jake Brake, Alcoa Aluminum Wheels. Includes approx. 640' of Drill Rod, Breakout Wrench, Lifting Plug, CAT Fuel & Oil Filters, CAT Engine Oil, Side Air Filters, Old Mud Pump that was Replaced (needs small weld patch). Recently changed fluids, filters. New batteries and some new hoses. Carousel Activator is not Working, needs Repaired. Mud Puppy Available for an Extra Cost.
Rotary D - SRS #4456
DESCRIPTION: 1986, Driltech; Model: T40K2H; Compressor: Sullair 1000/350; Engine: CAT 3406; Mounted On: CCC; Truck Engine Make: Diesel; Condition: Good Running Drill; Tools/Options: Driltech T40K2H Year: 1986: Rig is Set Up to Run 3.5" Drill Rod. M&R: One Link Removed from the Chains, Replaced the Top of the Bean Water Injection Pump and Installed a Piston Kit, New Master Links on the Chains to Tophead, Repaired Bushing Holes & New Bushings in the Tophead Plates, Replaced Detent Springs on the Feed Spool Control Handle, Rebuilt Tophead, New Bull Shaft, Bearings, Planetary Parts, Seals & O-rings. Filled with 75W-90 Full Synthetic Gear Oil, New Water Injection Hydraulic Hoses, Replaced Numerous Hoses, Welded Crack on Hydraulic Tank Outlet Port, Repaired Main Pump Seal & Shaft, Replaced Hoses in the Rear Cabinet, Full DOT, New Pressure Relief Valve, Welded up Cracks on the Mast Support Tubes, Valve Kit on Rear Valve Bank, New V-belts on the Chassis Engine, Reman on Alternator, New U-joint on the Chassis Drive Line, All Air Filters Changed, New Oil Pressure Switch on the Deck Engine, All New Oils & Coolant, Rear Rearend Rebuilt on the Chassis, New Oil in the Rear Ends, Couple of New Circuit Breakers, New Hydraulic Oil Filters and Oil, Deck and Chassis Coolant Filters, Temp Switch on the Deck Engine, New Air Dryer on the Chassis, Air (on/off) Cylinder Rebuilt, New Air Filter Cover, Checked Rod Carousel.. Condition: Good Running Drill
Rotary G - SRS #3914
DESCRIPTION: 1975, Gardner Denver; Model: 2000; Mud Pump: GD 7-1/2" X 10"; Engine: PTO; Mounted On: 4-Axle Crane Carrier; Truck Engine Make: 400 Cummins; Tools/Options: Gardner Denver 2000 Year: 1975: 58' Mast, 10" Retractable Rotary Table, Air Clutches, Two Drum Machine, No Sandline, No Rod Rack, 4-1/4" or 4-1/2" X 38' Hex Kelly (needs confirmed), Rig is set up to run 30' Rod. Has a Large Gardner Denver Swivel that has been Rebuilt, 2 Wells since. Has a Winch on the Side for Oil Field Dogs. Also Includes 810' of 5" X 30' Drill Rod with 3-1/2" IF Threads (used on 6 wells) and a Rod Trailer that was Purchased New and has < 300 Miles on it. Can be sold without rod.
Mud Grout Pumps - SRS #4541
DESCRIPTION: Mud Pump: 2023 Gardner Denver 5X6 FXG 172; Mounted On: Unmounted; Condition: Never Used; Tools/Options: Gardner Denver 5X6 FXG 172 Year: 2023 New, Never Used Gardner Denver 5X6 Mud Pump.
Rotary R - SRS #4493
DESCRIPTION: 1996, Reichdrill; Model: T-650 W II; Compressor: 1150/350; Mud Pump: None; Engine: CAT 3406B; Mounted On: 1996 Ford LT-8000; Truck Engine Make: Cummins 300 HP; Condition: Good; Tools/Options: Reichdrill T-650 W II Year: 1996: Brand New Compressor with approx. 140 Hours on it. Newer Upper and Lower Chains. 38,000# Rated Pullback Capacity, HD 160# Chains, 26,000# Down Pressure, Standard 140# Chains, Chains are about 2 years old, Spare Chain Parts Included. 34' Mast, (2) 4.5" Hydraulic Mast Raising Cylinders, Hydraulic Retractable Table, Carousel Holds 7 Rods, Hydraulic Breakout Wrench, 4-cylinder Bean Water Injection Pump, (2) Rear 36" and (1) Front 48" Leveling Jacks. New Valves on Top of Jacks, New Water Injection Control Valve. 3,000 psi Capacity Water Injection Pump Valve, Hydraulic Winch, Jib Boom, Rod Rack Capable of Holding (12) 4.5" Rods, Night Lights. Deck Engine has a New Starter and Newer Injection Pump, New Tach Installed a few Years Ago. Serviced every 200 Hours including the Funk Oil and Air Filters. Carousel and Rod Box Included but not on the Rig. Rig is set up to run 4.5" x 20' X 2 7/8 IF" Drill Pipe, Hour Meter Reads approx. 8,170. Truck has a 9-Speed Fuller Transmission,18,000# Front Axle, 46,000# Rear Axle, Hendrickson Suspension. Truck Engine has approx. 73,066 Miles on it. Includes a New, Full Set of Front and Rear Tire Chains. Rig is Operational. Includes J-Wrench, 48" Tongs, 48" Breakout Wrench, Rod Bushing, 6" and 8" Slips. Welder in Photo Not Included. Atlas 2000 Casing Hammer Available at an Extra Cost. Rod Box and Carousel Included.
Rotary T-Z - SRS #4368
DESCRIPTION: 2009, Versa Drill; Model: 100NG; Compressor: 500/200; Mud Pump: Mission 250 Series 3X4X13 & a Failing 5X6 Duplex; Engine: PTO; Mounted On: 2009 Peterbilt; Truck Engine Make: Diesel; Condition: PRICE REDUCED; Tools/Options: Versa Drill 100NG Year: 2009: 40K Pullback, Hydraulic Jacks, Main Winch & Sandline Winch,11-Rod Carousel, 2 3/8” ID with FEDP Threads 3” OD X 20' Pipe, Mission 250 Series Centrifugal Mud Pump with a 4" Discharge and a 5X6 Failing Duplex Pump, Hydraulic Quick Connects to Swap Two Hoses and Switch Between the Two. Truck has a Jake Brake, Manual Transmission, AC, Three Toolboxes, Odometer Reads 367,668 Miles and 18,380 Hours. Includes 400' of 3" X 20' Heavy Wall Pipe (will have New Box Ends & Tool Joints Replaced), (2) Drill Bit Subs (1) 6-5/8" API Regular Box Fish Necked to 3" OD FEDP 2-3/8" Box with 2-7/8" Tool Joints for Breaking, (1) 4-1/2" API Regular Box Fish Necked Down to 3" OD FEDP 2-3/8" Box with Tool Joints for Breaking. Rebuilt Fabco 200 Transfer Case is Available for an Extra Cost (0 hours). EXTENSIVE LIST OF M&R AVAILABLE.
Sold - SRS #4050
DESCRIPTION: 2016, Atlas Copco; Model: TH-60; Compressor: 1070/350; Mud Pump: Removed; Engine: PTO; Mounted On: 2014 Peterbilt 367; Truck Engine Make: Cummins ISX 600 HP - FACTORY NEW; Tires: NEW 95%; Condition: SOLD; Tools/Options: Atlas Copco TH-60 Year: 2016: 40K Pullback 30K Pulldown, 4,400 ft.-lbs. Maximum Head Torque, 2-Speed Head Rotation, 18,000# Winch, Hammer Lubricator, 7-Rod Carousel, Rig is Set up to Run 4.5" X 20' Drill Rod with 2-7/8" IF Rod, Rod Box Holds 18 Joints of Drill Rod, Bean 25 GPM/750 psi Water Pump. Truck has Two Fuel Tanks (150 and 85 gallon), Jake Brake, 19-Speed Eaton Transmission 68,000# GVWR, 22,000# Front Axle and 46,000# Rears. 425/65R22.5 Front Tires and 11R22.5 Rears. Recent Repairs and Upgrades: Top Breakout Wrench, Two New Lift Cylinder Pins on Mast, FACTORY NEW Cummins Engine, Gearbox Replaced with Newer Style Nimco, Installed Sandline, Single Rod Loader, New Cables, Brakes, Tires, Rod Spinner, Controls & Gauges Gone Though, Repaired. New Carousel Installed and Rollers in Shaft were Replaced with the Big Rollers. New Main Head, New Swivels & Pins, New Carousel, Replaced Seals & Bearings in Gearbox on Bottom, New Table Bushings. Electrical Control Box was Replaced, Grounded, Dash Wires all Gone through. All Work was either professionally done or Parts were Purchased New. Drill Rod Available, Diverter Optional. Currently has 38,278 Miles, 1,086 Engine Hours and 4,913 Compressor Hours. SOLD
Water Truck - SRS #4305
DESCRIPTION: Water Truck; Mounted On: 1998 Volvo Auto Car; Truck Engine Make: CAT 3406E 475 HP; Condition: PRICE REDUCED; Tools/Options: 2,200 Gallon Tank that has been Sandblasted and Painted. 20' Bed, 200 Gallon Fuel Transfer, IMT 2020 Teathered Control Crane. Truck has an Eaton Fuller 8LL Transmission, Jake Brake, 46K Full Locking Rears. Runs Strong, Doesn't Burn Oil or Blow Smoke, Miles Unknown
Rotary G - SRS #4517
DESCRIPTION: 2023, GEFCO; Model: 30K; Compressor: 1050/350; Mud Pump: 3" Wilden; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: Cummins 565 HP; Condition: Great; Tools/Options: GEFCO 30K Year: 2023: Holds 6 Rods in the Carousel and 15 in the Rod Box. Single Rod Loader, Rod Spinner, Hammer Holder, Foremost Shock Sub. Some Warranty Left out of the 5 Year Warranty. Rod that drill can hold is included along with a used 6" QL6 Hammer and an 8" Rebuilt Hammer with 8-3/4" Hammer Bit and a 8-3/4" Roller Bit with 15' Sub, 5-7/8" Roller Bit for Cleanout, Stabilizers, Bit Breakers, Slips, Pipe Lifters, 10-12 Bags of Mud. Also Includes a Water Truck (2) 20' Hoses, No Fuel Tank on the Truck but has a 120 Gallon Tank with an Electric Pump that could be Included. Rig is Set Up to Run 4.5" X 20' X 2-7/8" Drill Pipe. Hub Odometer Currently Reads 10,977 Miles, Total Rig Hours - 2,313 and Current Compressor Hours are 1,222.
Rotary G - SRS #4433
DESCRIPTION: 2016, GEFCO; Model: SS-22 RC HD; Compressor: DR 500/200; Mud Pump: 6X5X14 National; Engine: PTO; Mounted On: 2015 Peterbilt 367; Truck Engine Make: Cummins ISX15 525 HP; Tools/Options: GEFCO SS-22 RC HD Year: 2016: Telescoping Jacks, Original Build Sheet Shows 18" Failing 150 Ton Rotary Table, 6" Western Rubber Swivel, 6" Western Rubber Air Side Inlet, 23' Kelly Bar, 7" Dual Outside Air Flange Ends, 4-Part Kelly Line with14" Block, 4-Part Pipe Line with 14" Block, Sandline, 15' Mast Extension, 6" Swivel. Truck Odometer Reads 14,854 Miles and 5,206 Hours. Compressor needs a new air end. Some Flange Connection Outside Air Drill Pipe Available for an Extra Cost.
Auger - SRS #4394
DESCRIPTION: 2002, Mobile; Model: B61HDX; Engine: 4BT Cummins; Mounted On: 1992 Ford F800 2WD; Truck Engine Make: Ford 7.8L 210 HP; Condition: SOLD; Tools/Options: Mobile B61HDX Year: SOLD 2002: 3L8 Moyno Water Pump, In/Out, Side to Side Wiggle Tail, Main, Auxiliary & Saf-T-Driver Winches, 3 Outrigger Jacks, 2 Swingout Auger Storage Racks. Truck has approx. 156,000 Miles on it. Tooling in Photos Included. SOLD
Mud Grout Pumps - SRS #4538
DESCRIPTION: Mud Pump: GASSO 1654C 5X8; Engine: Detroit 471; Mounted On: Skid; Condition: Rebuilt; Tools/Options: GASSO 1654C 5X8: 250 Gallon Diesel Tank. New Expendables Included but not Installed. Enclosed Chain in Box, Enclosed Chain from Engine to Pump. 5-Speed Transmission (high pressure, low fluid).
Steel - SRS #4537
DESCRIPTION: Ingersoll Rand; Tools/Options: 500' of 4.5" X 20' Ingersoll Rand Drill Rod with 3.5" Connections. T4 Hex/Squares. Calipers a full 4.5" but some Pitted from Sitting.
Steel - SRS #4535
DESCRIPTION: Ingersoll Rand; Condition: Good; Tools/Options: Ingersoll Rand: Near New Ingersoll Rand 4.5" OD X 30' Drill Rod with 2-7/8" Threads. Approx. 1,020' (34 joints) Available.
Sold - SRS #4534
DESCRIPTION: Mud Pump: Gardner Denver 5-1/2" X 8"; Engine: See Below; Condition: Rebuilt; Tools/Options: GD 5-1/2" X 8": SOLD Completely Rebuilt Except for Bull Gear which is in Good Condition. New Expendables, Bearings, Liners, Rods, Pistons, Valves, Valve Seats. Equipped with a Shaft so it can run off of an Engine, Hydraulically or with a Pulley and Belt.
Mud Grout Pumps - SRS #4533
DESCRIPTION: Mud Puppy; Model: MP-255-25C; Engine: 73.9 HP Deutz; Mounted On: 2008 Heavy Duty Trailer; Condition: Runs and Works Great; Tools/Options: Mud Puppy MP-255-25C Year: New Deutz Engine Installed with 380 Hours on it and New Hydraulic Pump. Includes Extra Parts. Runs and Works Great.
Rotary G - SRS #1967
DESCRIPTION: Gardner Denver; Model: 3000; Mud Pump: 7-1/2 X 10 GD; Engine: (2) Detroit 6V71 Rebuilt in 2019; Mounted On: 6 Axle CCC; Truck Engine Make: 871T; Condition: Excellent; Tools/Options: Gardner Denver 3000 : Operating Daily! Re-manufactured in 2006. Double Drum with Sandline - 3 Drum line (no need for rathole), Kelly Track in the Derrick. Fast Drilling, Easy Removeable Table. 60' Racking Board. 1 deck engine drives the mud pump and the other engine drives the Drawworks. 70' mast, telescopes to 97', rated @ 250,000# with 100 ton Webb traveling block with 1" cables. 4" King swivel with 4-1/2" IF X 37' fluted Kelly. 18" Brewster Skytop oilfield table. (2) BJ breakout tongs, air clutches, (6) hydraulic jacks (4) screw jacks, 50 ton McKissick block (Kelly), operators platform. 4-5 yrs. old since completely rebuilt from ground up. Includes all the standards - elevators, slips, bushings. Has set 36" Casing, Table Lifts Out with Sling. Deck Engines Rebuilt in 2019. All 4 Rear Axles Pull.
Rotary H-I - SRS #4532
DESCRIPTION: 2001, Ingersoll Rand; Model: T3W; Compressor: 1070/350; Mud Pump: Wilden QLX-6; Engine: CAT 3406E; Mounted On: 2000 Mack; Truck Engine Make: E7; Condition: Very Good; Tools/Options: Ingersoll Rand T3W Year: 2001: Wilden Mud Pump is 3 Months Old, piping to Boss Fitting Swap Location. Truck has approx. 38,000 Miles on it. Includes 400' of 4" Drill Rod. Approx. 13,000 Total Rig Hours, Compressor Hours Unknown. Rebuilds Unknown. Manual Clutch for when Starting the rig. A 1997 Freightliner with 2,000 Gallon Flat Tank is Available for an Extra Cost. PBA CAT 3126 which was rebuilt about 4 years ago before purchased. 10-Speed with Jake Brake, Full Locking Rears, 200 Gallon Fuel Tank.
Rotary S - SRS #4401
DESCRIPTION: 2001, Schramm; Model: T450WS; Compressor: Sullair 900/350 w/ Clutch; Mud Pump: Mission Magnum; Engine: CAT 3206; Mounted On: 2001 IHC 6X4; Truck Engine Make: Diesel; Tools/Options: Schramm T450WS Year: 2001: Pullback 30,000#, Pullback, 17,000# Pulldown. Dual Tophead Motors, 28'6" Mast Travel. Four Outriggers, Braden PD15 Winch, 15,000# Capacity. 10-Rod Carousel, Rig Holds 480' of 3-1/2" X 2-7/8" X 20' Drill Pipe, Hydraulic Table and Break-out Wrench (48" but cant take 60"), 205 Gallon Fuel Tank, Hammer & Stabilizer Holder, Sliding Tophead, Water Injection, Pipe Rack, Jib Boom with Hydraulic Swing, No Sandline. Truck has 56,000# GVWR, 16,000# Front, 46,000# Rears. CAT 3206 Deck Engine Rebuilt (Sept 2024),Tophead also Rebuilt (Nov. 2024). Currently having a New Mast Installed. Service Records Available. Compact Drill Good for Geothermal and Mineral Exploration. Truck Odometer Reads 003,300.4 Hours. Compressor Hours Unknown. Truck Odometer Miles 077,103.9. No Rod & Tooling Included. Currently having a new mast installed. OFF MARKET, PUT BACK TO WORK
Pump Hoist - SRS #4512
DESCRIPTION: 2016, Hunke; Model: 6T; Engine: PTO; Mounted On: 2016 Ram 5500 4WD; Truck Engine Make: Cummins 6.7L; Tools/Options: Hunke 6T Year: One Owner, Sandline with approx. 1,000' of Cable, 3 Outriggers, Hunke Tilting Pipe Racks. Owner believes there is a wired remote. Truck is Equipped with Power Windows, AC and has approx.. 98K Miles. 11' Palfinger Bed, Spray in Bedline. There is Moderate Damage to Driver Side Front Corner, Swiped 6 Years Ago. The Door was modified to close securely and was used daily in it's current state.
Auger - SRS #4531
DESCRIPTION: 1995, CME; Model: 55; Engine: Deutz 5-Cylinder; Mounted On: 2014 IHC SBA 4300 4X2; Truck Engine Make: Diesel; Condition: Working Rig; Tools/Options: CME 55 Year: 1995: 3,200# Mainline, (2) 1,800# Winch lines (fast/slow), Auto Hammer. Cathead is not mounted but available, (3) Jacks, Wiggle Tail. 3L8 Pump and Water Tank are both Trailer Mounted Making the Rig under CDL. Truck Odometer Reads 225,686. No Rod or Tooling Available. TEMPORARILY OFF MARKET
Sold - SRS #4370
DESCRIPTION: Flatwater Fleet; Model: 2,400 Gallon; Mounted On: 2008 IHC 7600; Truck Engine Make: CAT C13 410 HP; Condition: SOLD; Tools/Options: Flatwater Fleet: 2,400 Gallon Flatwater Fleet Flat Tank, 30' Remote Stellar Crane. (2) 100 Gallon Fuel Tanks on the Deck with a Transfer Pump & Numerous Tool Boxes. Truck has an 18-Speed Transmission, Air Ride Suspension and Both Seats have Air Ride, Jake Brake, Full Lockers, approx. 109,000 Miles on it. 18k Front and 46K Rears, 64K GVWR. SOLD
Sold - SRS #4510
DESCRIPTION: 1982, Speedstar; Model: SS 135 HD; Compressor: Yes, Developmental - To Be Confirmed; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2006 IHC 7600; Truck Engine Make: Cummins ISX 15; Tires: New; Condition: SOLD; Tools/Options: Speedstar SS 135 HD Year: 1982: SOLD Hydraulic Drawworks Rebuilt 6-8 Years Ago, Painted approx. 5 Years Ago. Mud Pump Had Gear End Rebuilt Two Years Ago and Fluid End about 6 Months Ago (2025), 4-Part Kelly Line and 4-Part Trip Line. Newer 3-3/4" Fluted Kelly with Drive Bushings. Four Leveling Jacks and has Pulldowns. All Hydraulically Driven except for Air Clutches. Hydraulically Driven 8-1/2" Rotary Table Rebuilt a Few Years Ago, Chain Box Completely Rebuilt 4 Years Ago. New Motor 4 Years ago (2021) New Clutch and 8 Brand New Tires, New Tranny. Bearings out on the Air Compressor Drive Clutch, has all the parts, just needs rebuilt. New Gauge Cluster was Installed when Engine and Drill was Installed on the IHC Chassis. Includes 400' of 3.5" Flush Joint Drill Pipe with 2-3/8" IF Threads. Truck has an 8-Speed Transmission and approx. 200,000 Miles on it. Engine and Transmission has approx. 80,000 Miles since Engine and Clutch was Replaced. SOLD
Pump Hoist - SRS #4516
DESCRIPTION: 2024, TDH; Model: 6X2; Engine: PTO; Mounted On: 2024 Ford F600 4WD; Truck Engine Make: 6.7L Power Stroke Diesel; Condition: Working Unit; Tools/Options: TDH 6X2 Year: 2024: Two Line Machine, Remote. Power Stroke Diesel Engine, Extra Rear Springs, approx. 17,000 Miles on Truck, Subject to Change. All Aluminum Boxes, Three Leveling Jacks. Working Unit. No Mechanical Issues.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |