Rigs
Rotary H-I - SRS #4518
DESCRIPTION: 1985, Ingersoll Rand; Model: TH-60; Compressor: 750/250; Engine: PTO; Mounted On: 1988 Paystar 5000; Truck Engine Make: 8V92T Detroit; Condition: Working Drill - Package Deal Open to Offers; Tools/Options: Ingersoll Rand TH-60 Year: 1985: 13-Speed, All New Drive Lines, Transfer Box has been Rebuilt. Detroit and Air Compressor have been Replaced. Lots of New Hydraulic and Air Hoses. Machine has been Refurbished. Includes a 1996 IHC 2674 Truck with a 2,200 Gallon Water Bed, 200 Gallon Diesel Tank on Headboard, Overall Bed is 25', Rod can go under headboard, IMT Crane with Corded Remote, Powered by a N14 Cummins Engine. 8LL Transmission, 3-Stage Jake Brake, 8 New Tires on Rear. 400' of Drill Rod Available for an Extra Cost. Will Sell Drill Separate from Water Truck.
Auger - SRS #3857
DESCRIPTION: 1972, Mobile; Model: B56; Mounted On: 1978 GMC 6500; Truck Engine Make: V8 Gas; Condition: Garage Kept; Tools/Options: Mobile B56 Year: 1972: 5' Stroke, Cathead, 2,500# Hoist, 2 Jacks. Truck has 48,000 Original Miles on it. Garage Kept, Under CDL. OPEN TO OFFERS
Auger - SRS #4577
DESCRIPTION: 1997, Diedrich; Model: D120; Mud Pump: Moyno 3L8; Engine: PTO; Mounted On: Buggy; Truck Engine Make: JD 6059;
Sold - SRS #4576
DESCRIPTION: Chicago Pnuematic; Model: T-650 WS; Compressor: 825/250; Engine: CAT 3406 A; Mounted On: 1978 Ford; Truck Engine Make: Diesel; Condition: Good; Tools/Options: Chicago Pneumatic T-650 WS: Brand New Compressor in 2025. Rig is in Very Good Condition for the Age. 500' of 4.5" Drill Rod and an Atlas Casing Hammer Available for an Extra Cost.
Sold - SRS #3925
DESCRIPTION: 2007, Deep Rock; Model: 150 4X Track; Compressor: Plumbed; Mud Pump: 4X3 Centrifugal; Engine: PTO; Mounted On: Tracks; Truck Engine Year: 120 HP Perkins Diesel; Condition: SOLD; Tools/Options: Deeprock DR 150 4X Tracks Year: 2007: SOLD Geothermal Drill Great for Tight Residential Areas. Tophead Torque 2,500 or 5,000 Ft. Lbs. Tophead Rotation 1-150 or 0-75 (hi torque), 16,000# Pullback. Approx. 2,288Hours, Runs 10' Drill Pipe, 11' Stroke, Mast can Handle 20' Casing, has a Jib Boom and Auto Breakout, Includes 300' of 2-3/8" Mayhew Jr. Drill Rod, One each 2-3/8" X 4-1/2" reg., 2-3/8" X 2-3/8" reg., 2-3/8" X 2-7/8" reg Bit Subs, Rosewall Grouter with 2" Bowie Pump (new pump), 200' of Jet Auger, Mud Pan, Desander Cone. Current Owner has Run a Portable Air Compressor in the Past, Just Plugs in. SOLD
Rotary S - SRS #4556
DESCRIPTION: 2008, Schramm; Model: T450WS; Compressor: 900/350; Engine: CAT 3406C; Mounted On: 2008 IHC 7500; Truck Engine Make: 570 HP; Condition: Working Drill - OPEN TO REASONABLE OFFERS; Tools/Options: Schramm T450WS Year: 2008: Hydraulic Welder, Oiler, New Rubber in the Back, Hendrickson Suspension, 30K Pullback, Rig is Set Up to Run 3.5" Drill Rod. New Chains in the last 2-1/2 Years, New Rollers in Mast, Mast is Straight, 3 Outriggers, 15-Rod Carousel, Bean Water Injection (rebuilt in 2024), Swinging Jib, Hydraulic Breakout Wrench, Aluminum Tool Box, No Sandline. Needs a New Sock in the Derrick. Includes 600' of good/used Drill Rod, Head Doughnuts, Complete Hose Kit for Big Compressor Hoses (1 hose used), Valve Rebuild Kit. Truck has approx. 54,000 Miles on it and Rig has approx. 7,000 Hours. Another 600' of Brand New 3.5" Drill Rod is Available for Extra Money. Truck Engine HP to be Confirmed.
Sold - SRS #4401
DESCRIPTION: 2001, Schramm; Model: T450WS; Compressor: Sullair 900/350 w/ Clutch; Mud Pump: Mission Magnum 6X4; Engine: CAT 3206; Mounted On: 2001 IHC 6X4; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Schramm T450WS Year: 2001: Pullback 30,000#, Pullback, 17,000# Pulldown. Dual Tophead Motors, 28'6" Mast Travel. Four Outriggers, Braden PD15 Winch, 15,000# Capacity. 10-Rod Carousel, Rig Holds 480' of 3-1/2" X 2-7/8" X 20' Drill Pipe, Hydraulic Table and Break-out Wrench (48" but cant take 60"), 205 Gallon Fuel Tank, Hammer & Stabilizer Holder, Sliding Tophead, Water Injection, Pipe Rack, Jib Boom with Hydraulic Swing, No Sandline. Truck has 56,000# GVWR, 16,000# Front, 46,000# Rears. CAT 3206 Deck Engine Rebuilt (Sept 2024),Tophead also Rebuilt (Nov. 2024). New Mast Installed in 2025, Rebuilt Engine, New Hydraulics. Service Records Available. Compact Drill Good for Geothermal and Mineral Exploration. Truck Odometer Reads 003,300.4 Hours. Compressor Hours Unknown. Truck Odometer Miles 077,103.9. No Rod & Tooling Included. Currently having a new mast installed. SOLD
Sold - SRS #4363
DESCRIPTION: 2023, Reichdrill; Model: RTD 69; Compressor: 1070/375; Engine: PTO; Mounted On: 2023 Peterbilt; Truck Engine Make: X15 605 HP; Condition: SOLD; Tools/Options: Reichdrill RTD 69 Year: 2023: SOLD. 43,980# Pullback, 160 HS Chain, 35,000# Pulldown, 140 HS Chain, REGEN, Air Operated Holding Wrench with Hydraulic Raising/Lowering, 7-Pod Carousel for 4" X 20' Drill Rod, 8-Gallon Air Line Lubricator, Multicore Cooler, Thermostat Controlled Fan Circuit for Improved Cooling and Fuel Savings, 34' Mast with 28' Stroke, 22" Table Opening, Dual Winches (8,500#), Hydraulically Extendable Jib, Wireless Radio Helper's Remote Controls for Jib Swing, Extend & Retract, Carousel Index/Lock, Winch Up and 2-Speed Winch Down, 20 GPM Water Injection Pump, Torque Limiter Control, Holdback Control, Feed Override all with bypass on & off. Mudline Stand Pipe with Hose Spud & End Cap, Cribbing Rack, 4 Leveling Jacks(36" & 48"), 18 Piece Rod Box, Drill Pipe Lifting Rod, Two Hammer Holders (7" & 10"), Diverter, Hydraulic Welder, Set Up to Run 4" Drill Rod. Capable of Holding 600' of Rod per Owner. Toolbox, Folding Rear Platforms Vandal Cover, Halogen Night Lighting. Truck has an 18-Speed Transmission, Differential Lock, 20K Steerable Lift Axle, Bluetooth, A/C, Heated Mirrors, Aluminum Wheels, Dual 80 Gallon Fuel Tanks, DEF Tank. Includes 1,000' of Rod. Stabilizer holder for the carousel is available but isn't on the rig, taken off to hold 2 more rods. Approx. 2,100 Hours and approx. 2,100 Miles. Condition: Near New SOLD
Rotary G - SRS #4433
DESCRIPTION: 2016, GEFCO; Model: SS-22 RC HD; Compressor: DR 500/200; Mud Pump: 6X5X14 National; Engine: PTO; Mounted On: 2015 Peterbilt 367; Truck Engine Make: Cummins ISX15 525 HP; Tools/Options: GEFCO SS-22 RC HD Year: 2016: Telescoping Jacks, Original Build Sheet Shows 18" Failing 150 Ton Rotary Table, 6" Western Rubber Swivel, 6" Western Rubber Air Side Inlet, 23' Kelly Bar, 7" Dual Outside Air Flange Ends, 4-Part Kelly Line with14" Block, 4-Part Pipe Line with 14" Block, Sandline, 15' Mast Extension, 6" Swivel. Truck Odometer Reads 14,854 Miles and 5,206 Hours. Compressor needs a new air end. Some Flange Connection Outside Air Drill Pipe Available for an Extra Cost. Not confirmed but seller was told it has 90K pullback when the block is at the table and 70K pullback when it's at the top of the mast.
Water Truck - SRS #4575
DESCRIPTION: Flatwater; Model: 1,100 Gallon; Mounted On: 1990 IHC Single Axle; Truck Engine Make: Diesel; Tools/Options: Flatwater 1,100 Gallon: Single Axle Truck with a 5-Speed Transmission. Also has a GEO-Loop 50-500 Grout Pump Mounted on Deck with a 500' Hydraulic Hose Reel and a 500' Loop Reel. Grouter has a New Honda Engine. Grout pump can be sold separately.
Water Truck - SRS #4574
DESCRIPTION: Flatwater; Model: 800 Gallon; Mounted On: 1995 GMC Top Kick Single Axle; Truck Engine Make: Gas; Tools/Options: Flatwater 800 Gallon: 800 Gallon Flatwater, 17', 6,000# Liberator Crane, Also has a 1500 Gallon Plastic Tank on Top, 100 Gallon Square Fuel Tank. Single Axle Truck with Automatic Transmission with Auxiliary Hydraulic System.
Rotary H-I - SRS #4570
DESCRIPTION: 1991, Ingersoll Rand; Model: TH-60; Compressor: HR2 750/250; Engine: PTO; Mounted On: 1992 IHC Paystar 5000; Truck Engine Make: Cummins N14; Condition: PRICE REDUCED; Tools/Options: Ingersoll Rand TH-60 Year: 1991: Everything Runs and Operates as it Should. There are (2) Joints of 3.5" X 20' Drill Pipe on the Rig, Included. 3.5" Rod Carousel in the Derrick. Rod Rack on the Side. Hydraulic Table and Breakout Wrenches. 37' or 38' Mast, Main Winch, Sandline Winch, Bean Pump, Hydraulic Jib with Scope on the Derrick, (2) Front and (2) Rear Jacks, Driller and Helpers Platforms. Odometer Reads 029,185 km 18,134 Miles. Hour Meter Reads 8,181
Rotary S - SRS #4573
DESCRIPTION: 1976, Speedstar; Model: SS15; Compressor: 256S 500/250 NOT MOUNTED; Mud Pump: GD 5X6; Mounted On: CCC; Truck Engine Make: Cummins 290; Tools/Options: Speedstar SS15 Year: 1976: 8-1/2" Retractable Table, Mechanical Clutches, Mast Extension Capable of Picking up 45' Pipe. Air Compressor Condition Unknown, Current Owner Never used it. New Pro Heat Engine Heater, New 2" Little Giant Swivel, New LF Breakout Tongs. Fresh Rebuild on the Lift Cylinders, Hydraulic Pumps and Motors. Mud Pump has had New Rods, Pistons, Valves, Seats, Liners and Packings Installed. New 700' of Sandline and 500' of New 4.5" X 20' Drill Rod with 2-7/8" IF Threads, 100' Never been in the ground. New 4.5" X 3' X 2-7/8" IF Sub with new 6-1/2" PDI Bit. New Sub 5-1/2" X 3' with 7-7/8" Roller cone Bit, (1) Hoisting Plug (2-7/8" IF), New work Platform, New Clutch for Mud Pump, New Pull Down, Shaft, Pillow Block Bearings and Sprockets. 500' of Rod will fit in rod box, compressor was removed and not used due to weight.
Mud Grout Pumps - SRS #4572
DESCRIPTION: 2018, Elgin; Model: CSI-D4 Cuttings Dryer; Mounted On: 8' X 28' X 8.5" Skid; Tools/Options: Elgin CSI-D4 Cuttings Dryer Year: 2018: Elgin CSI-D4 Vertical Cuttings Dryer, Skid Mounted Solids Control Unit Designed for Oilfield Drilling Operations. Includes VFD Controlled Operation for Efficient Cuttings Drying and Fluid Recovery. Built for use in Closed Loop Mud Systems to Reduce Waste and Maximize Drilling Fluid Reuse. Ideal for Land Based Rig Setups or Stationary Environmental systems. Compact, High Capacity Unit for Oil Based and Synthetic Based Mud Applications. Electrical control System with Protective Cage and System Wiring Package. Non Explosive Proof NEMA 4X Stainless Steel VFD Cabinet. One 60 HP Yaskawa VFD VCD Drive and One 15 HP Yaskawa. One 7.5 HP A1000 PC Pump Drive, One 5 HP VFD Feed Auger Drive. HMI Touch Screen Interface, non explosion proof Wiring and Glads. 600 Gallon Dish Bottom Tank, 6" Flanged Inlet Connection, dual 3" Cam Lock Outlet Connections, 6" Flexible connection from VCD, dual Swivel Mud Gun Jet Mixers, Hinged Lid with Dual Lifting Points. Fixed Height VCD Stand, Working Deck with Walkways and Railings, Stair Case & Removeable Ladder, 110V Power Outlets. 3X3 Self Priming, Solids Handling Centrifugal Pump Package, VFD Driven Progressive Cavity Centrifuge Feed Pump Package, Removable Hopper Assembly, 24" X 24" Belt Conveyor Package.
Mud Grout Pumps - SRS #4571
DESCRIPTION: 2020, Elgin; Model: ESS-1967; Mounted On: 42' 5th Wheel Trailer; Tools/Options: Elgin ESS-1967 Year: 2020: XP Polisher Centrifuge with ESS-1967 HD2 on a Trailer. Elgin ESS-1967 HD2 XP Solids Control Centrifuge. 60V/60Hz or 380V/50Hz. Powder Coated. NEMA 4X Stainless Steel Control Panel, HMI Touch Screen Interface with (3) Yaskawa GA-800 VFD Drives. Integrated with Trailer on Vibration Isolation Pad, Integrated Controls for Centrate Pump and Screw Conveyor. Progressive Cavity Feed Pump, 460V/60Hz - 3 Phase 500 GPM, 150 kW Genset Mounted on a 45,000# 5th Wheel 42' Trailer.
Rotary S - SRS #4495
DESCRIPTION: 2005, Schramm; Model: T555; Compressor: 1050/350 with Clutch; Engine: Diesel; Mounted On: Sterling; Truck Engine Make: Mercedes Diesel; Condition: Running Drill; Tools/Options: Schramm T555 Year: 2005: Rig has 4 Jacks. Includes approx. 400' of 4.5" O.D. Drill Rod, (5) Joints are older 25'ers and the rest are 20'ers in better condition, a 6" and 8" Hammer & Bits, tools, Hydraulic Wrench, Casing Driver and Stabilizer. Last drilled early 2025. Odometer Reads 29,972 Miles. Total Rig Hours are approx. 10,000. Compressor has a clutch and has less hours but hours are unknown. Recently Installed a New Compressor Cooler (zero hours), New Shaft & Bearings in Rotary Head, Four Rebuilt Hydraulic Pumps and one new Pump.
Rotary A-B - SRS #4568
DESCRIPTION: 2007, Atlas Copco; Model: RD20 III; Compressor: IR 1250/350; Mud Pump: FMC Triplex Mist; Engine: CAT C27; Mounted On: 5-Axle CCC; Truck Engine Make: CAT C13; Tools/Options: Atlas Copco RD20 III Year: 2007: Hydraulics are Powered by the CAT C7. 30,000# Pulldown, 120,000# Pullback Capacity, 52' Range III Tower, FMC Triplex Mist Pump Powered by a Hydraulic Motor, Downhole Lubricator, Shock Sub, Braden Utility Winches. Included the following support equipment: Bomco F-800 Triplex Mud Pump, 7,500' of 3.5" X 30' Drill Pipe, (5) 6" Drill collars, Hammers & Bits (8" SD8 Hammer & Bits, 10" SD8 Bits, 12-/14" SD8 Bits plus TCI Bits (8-3/4", 10", 12-1/4", 17-1/2"), Three Crossover Subs. 2006 IR 1170/350 Compressor & Ariel JGQ/2 Single Stage Air Booster, Mack Pipe Truck. Well Control Equipment includes a 7-1/6" BOP (5,000 psi), Annular BOP, Accumulator, Choke Manifold. Handling Tools Include a Petol Wrench and Safety Clamp. Carrier has a Single Man Cab, Eaton 8-Speed Transmission, (5) Hydraulic Leveling Jacks, Drillers Control, 17-1/2" Table, 750 HP Engine. Maintenance Performed includes - Rebuilt Engine and Hydraulic Cylinders, Replaced Batteries, Turbo, Starter, ECM, Filters and Tires, New Paint and the Clutch and Brake Lines were Repaired.
Water Truck - SRS #4565
DESCRIPTION: NCM; Model: DRSU 1200 Gallon; Mounted On: 1997 Ford; Truck Engine Make: CAT C12; Tools/Options: NCM DRSU 1200 Galllon Water Truck: IMT 4004i Crane (welder not included). 1,200 Gallon Bed is approx. 28 Years Old. Truck Frame has some cracks in 4 spots. Water Bed has 3 Valves, no leaks. Truck has over 1 Million Miles on it.
Sold - SRS #4533
DESCRIPTION: Mud Puppy; Model: MP-255-25C; Engine: 73.9 HP Deutz; Mounted On: 2008 Heavy Duty Trailer; Condition: SOLD; Tools/Options: Mud Puppy MP-255-25C Year: New Deutz Engine Installed with 380 Hours on it and New Hydraulic Pump. Includes Extra Parts. Runs and Works Great. SOLD
Rotary D - SRS #4456
DESCRIPTION: 1986, Driltech; Model: T40K2H; Compressor: Sullair 1000/350; Engine: CAT 3406; Mounted On: CCC; Truck Engine Make: Diesel; Condition: Good Running Drill OPEN TO OFFERS; Tools/Options: Driltech T40K2H Year: 1986: OPEN TO OFFERS!! Rig is Set Up to Run 3.5" Drill Rod. M&R: One Link Removed from the Chains, Replaced the Top of the Bean Water Injection Pump and Installed a Piston Kit, New Master Links on the Chains to Tophead, Repaired Bushing Holes & New Bushings in the Tophead Plates, Replaced Detent Springs on the Feed Spool Control Handle, Rebuilt Tophead, New Bull Shaft, Bearings, Planetary Parts, Seals & O-rings. Filled with 75W-90 Full Synthetic Gear Oil, New Water Injection Hydraulic Hoses, Replaced Numerous Hoses, Welded Crack on Hydraulic Tank Outlet Port, Repaired Main Pump Seal & Shaft, Replaced Hoses in the Rear Cabinet, Full DOT, New Pressure Relief Valve, Welded up Cracks on the Mast Support Tubes, Valve Kit on Rear Valve Bank, New V-belts on the Chassis Engine, Reman on Alternator, New U-joint on the Chassis Drive Line, All Air Filters Changed, New Oil Pressure Switch on the Deck Engine, All New Oils & Coolant, Rear Rearend Rebuilt on the Chassis, New Oil in the Rear Ends, Couple of New Circuit Breakers, New Hydraulic Oil Filters and Oil, Deck and Chassis Coolant Filters, Temp Switch on the Deck Engine, New Air Dryer on the Chassis, Air (on/off) Cylinder Rebuilt, New Air Filter Cover, Checked Rod Carousel.. Condition: Good Running Drill
Auger - SRS #4564
DESCRIPTION: 2006, CME; Model: 75; Mud Pump: Gardner Denver 4-1/2" X 5"; Engine: Cummins 6BT; Mounted On: IHC 7400; Truck Engine Make: DT 466E; Tires: Rear 11R22.5 Front 385/65R22.5; Tools/Options: CME 75 Year: 2006: Rig has 15,082 Hours, 5-speed Transmission. 3-Pump Hydraulic System (tandem gear pump and one variable displacement pump dedicated to the mud pump). 25' Mast from Base Frame, has Angle Drill Spec, High Speed Head with in/out and Side to Side Slide Base, Fluted Kelly with Quick Disconnect Hydraulic Chuck (2-5/8"), 8,500# Main Winch, 3.200# Auxiliary Winch, 1,800# Auxiliary Winch and Fast Wireline Winch. 140/300# Auto Hammer. 4-1/2" Hydraulic Rod Holder and Breakout Wrench, Hydraulic Underside Slide out Auger/Casing Rack, Underwater Tank Storage, Rod Rack for 10 Rods. 2" Mud Discharge Plumbing, Under Deck 3" Suction and Freshwater Plumbing, 900 Gallon Stainless Water Tank. Truck has approx. 110,000 Miles, Allison MD 3060 Automatic, Double Frame Chassis with 20K Rears and 14K Front Axle, 20,000# Front Winch.. Condition:
Sold - SRS #4563
DESCRIPTION: Badger; Model: 1250; Compressor: GD 427; Mud Pump: Failing 5X6; Engine: PTO; Mounted On: 1995 Ford; Truck Engine Year: CAT 3406; Condition: SOLD; Tools/Options: Badger 1250: Bean Pump, 7-1/2" DSM Table, Mechanical Clutches, Two Leveling Jacks, 4-Speed Pulldown, 2" Little Giant Swivel. Lots of New Components on Drill and Truck. Spicer 792 Transfer Case (air shift)5-Speed Rotary Transmission, 4-Speed with Reverse, 8LL Transmission. Includes 200' of New Drill Rod. SOLD
Sold - SRS #4559
DESCRIPTION: 1996, Ingersoll Rand; Model: T2W; Compressor: 750/300 IR Screw; Mud Pump: 3X4X13; Engine: PTO; Mounted On: 1995 IHC 2674 6X4; Truck Engine Make: Cummins N14 370 HP; Condition: SOLD; Tools/Options: Ingersoll Rand T2W Year: 1996: SOLD 4 Digit Hour Meter Shows 4,341 Hours ? 30,000# Pulldown and 30,000# Pullback, 18 GPM Bean Pump, DHD Injection Oiler. Dual Motor Tophead, Black Top Cummins Engine in Truck, has a Spicer 10-Speed Transmission, 47,999 GVWR and 451,085 Miles. Set up to run 2-3/8" FEDP Rod, 4.5" Carousel is available. Seals were done in the PTO, Top End in Engine was Redone < 1,000 Hrs. ago along with some other M&R work. Drill Rod Available. SOLD
Rotary G - SRS #4558
DESCRIPTION: Seismic; Model: Mud & Air Drill; Compressor: GD 680; Mud Pump: GD 5X6 (Belt Driven); Engine: PTO; Mounted On: 2007 Kenworth; Truck Engine Make: CAT (big one); Condition: Great; Tools/Options: Seismic Mud Drill. Current owner had it down to 500', Mud Drilling. Mast is longer than the standard mast, approx. 34', Mud Pump is Belt Driven and has its own Clutches (can shut off when running air compressor). Has a New Table (same as a Badger, has a Quill that can be removed). Has been Re-decked and repainted. Runs 2-7.8" O.D. Drill Rod with Mayhew Regular Thread. Odometer Reads 3,928 Miles (drilling), 46K Rears, 20K Front Axle Full Lockers, Double Frame, Pre-emission CAT Engine (big one), Spicer Gearbox (new), Pro Heat. Mud Pan Included
Sold - SRS #4557
DESCRIPTION: 2025, Mobile ; Model: B-25; Mud Pump: None; Engine: PTO; Mounted On: Raymar TRK60S Rubber Tracks; Truck Engine Make: 44 HP Kubota Turbo Diesel; Condition: SOLD; Tools/Options: Mobile B-25 Year: 2025, 4-Speed Rotary Head, 76" Single Cylinder Feed System, Auger/Tool Guide Support, Triple Hydraulic Pump, All Controls Located in Control Panel, Emergency Shut Down, 1-5/8" Hex Safety Auger Coupling, Front Mounted Auger. 140# Auto SPT Hammer, NWJ Hammer Rod Pin. 4,500# Auxiliary Hoist, 3,000# Auxiliary Hoist, 18' Mast, Shelby Tube Sampler Extruder (3" X 30") Mounted on Helper Side, Fold Down 18" X 18" Fold Down Work Table, Breakout Accessories - Single Jaw Rod Clamp & 24" Cylinder Mounted Breakout Wrench, Tool Box, 5' Rod Rack, (4) 24" Hydraulic Leveling Jacks. NWJ Thread Connection, 3-1/4" 2K Standard Auger Connection. Rubber Tracks: OAL 74.3" Long, 9" Wide Tracks. Hydraulically Powered Planetary Drive with Internal Brakes, Wireless Remote Control & Manual Controls Mounted on Carrier, 20 Gallon Fuel Tank. Never Used. Includes a 2025 2 Axle, 22' Trailer. SOLD
Rotary E-F - SRS #4548
DESCRIPTION: Failing; Model: 314C; Mud Pump: Gardner Denver 5X6; Mounted On: 1984 Ford F700; Truck Engine Make: 370 - 429 V8 Gas; Tires: Hold Air but Older; Condition: Good - Working Drill PRICE REDUCED; Tools/Options: Failing 314C: PRICE REDUCED. Includes some bits and attachments. Truck Engine has a 5-Speed Transmission, 2-Speed Rear Axles Runs & Drives. Rig has a Main Winch and it also has a Sandline Winch. Table size looks to be 3-3/4" and it runs either N3 or N4 Drill Pipe. Everything works as it is supposed to, needs a little TLC to make it perfect. Truck will need some brake work and rig will need drop pipes. Tire hold air but are old (+/- 10 years old).
Pump Hoist - SRS #4489
DESCRIPTION: Reichdrill; Model: Eagle; Mounted On: GMC 5500 4X4; Truck Engine Make: Duramax Diesel; Tools/Options: Reichdrill Eagle: Three Line Machine, 6,000# Single Line, Allison Automatic Transmission.
Rotary D - SRS #4552
DESCRIPTION: 2007, Driltech; Model: T25; Compressor: 1150/350; Engine: CAT C15; Mounted On: 2007 Sterling; Truck Engine Make: Mercedes; Tools/Options: Driltech T25 Year: 2007: Approx. 9,000 Original Hours, approx. 4,500 Compressor Hours. Driller & Operators Platforms, Two Rear Jacks and Two Behind the Cab, Rod Rack, Toolbox, Hammer Holder, Carousel. Includes 900' of 4.5" Drill Rod, Bits, Stabilizer. Also includes a 2,000 Gallon Sterling Water Truck with 20' Bed. Rig can be sold separately also.
Rotary G - SRS #4555
DESCRIPTION: 1978, Gardner Denver ; Model: 1500; Compressor: 667 2-Stage; Mud Pump: 5-1/2" X 8" FLUID END AND POWER END (2026) RECENTLY REBUILT; Mounted On: 1978 Ford L9000; Truck Engine Make: CAT 3208; Tools/Options: Gardner Denver 1500 Year: 1978: 10" Sliding Rotary Table, Manual Clutches, Triple Line Kelly and Sandline, 24; Kelly, Kelly Clutch Overhauled. Rig is set up to run 3.5" X 15' Pipe and has a 15' Rod Box, 4 Leveling Jacks (one just recently repacked 2026). Master Cylinder on Driller side has been Repacked. Power End (2026) and Fluid End recently rebuilt, Pinion Bearings in Rotary Table Replaced (2026), Truck has a 13-Speed Transmission and Engine has a New Water Pump and Belts. Will Include 735'' of 3.5" Drill Pipe, 6", 8" and 10" Stabilizers. Recently Painted.
Rotary A-B - SRS #4554
DESCRIPTION: 2008, Atlas Copco; Model: TH-60; Compressor: 900 HR.2; Mud Pump: Plumbed; Engine: PTO; Mounted On: Peterbilt Tri Drive; Truck Engine Make: 600 HP Cummins ISX; Tires: New; Condition: Spare Drill; Tools/Options: Atlas Copco TH-60 Year: 2008: New Fabco 172 Transfer Case, New Tires, Front & Rear. Completely New Fully Rebuilt Engine (2017 - Borg Warner parts) with approx. 2,600 Hours on it. New Hydraulic Cooler in 2021, Truck has approx. 10,000 Hours and < 124,500 Miles. Drill has approx. 6,200 Hours and approx. 2,470 Compressor Hour. Fleet Maintained, Service Records Available and hasn't been used in 5 years as it was a spare drill. Rod Rack is included. Rig is Plumbed for a Centerline Mud Pump. 7X10 Aluminum Centerline duplex mud pump is available for an extra cost. Rig is set up to run 3.5" Drill Pipe.
Auger - SRS #4550
DESCRIPTION: Diedrich; Model: D-120; Mud Pump: SP-50; Mounted On: 2003 ATV with Rubber Tires; Truck Engine Make: John Deere 6.8 L; Tools/Options: Diedrich D120: Rig had every option available at the time of purchase. Original Owner.
Sold - SRS #4549
DESCRIPTION: 1985, Speedstar; Model: 985; Compressor: Removed; Mud Pump: 5X4 Centrifugal; Engine: Detroit 8V92; Mounted On: 4-Axle CCC; Truck Engine Make: Detroit; Condition: SOLD; Tools/Options: Speedstar 985 Year: 1985: 70K Rope Head Drive, Tophead Retracts. Includes 500' of 4.5" Bottleneck Drill Pipe. Drill had and air compressor on it prior to current owners ownership. Table opening is at least 28" plus a bushing Insert that will close it up to approx. 15". Mast is about 42' (to be confirmed). Rotary Head, 60K Winch Line, Swinging Jib with Winch. Detroit Engine under the hood with a Power Tower. SOLD
Sold - SRS #4497
DESCRIPTION: 1983, Bucyrus Erie; Model: 22W Series III; Engine: 3-Cylinder Deutz Diesel; Mounted On: 1990 IHC; Truck Engine Make: Diesel; Tires: Good; Condition: SOLD; Tools/Options: Bucyrus Erie 22W Series III Year: 1983: approx. 700' of 3.4" Drill Line and approx. 700' of 3/8" Sandline, Hydraulic Jacks. 2025 Had a Brand New Shaft Installed along with New Bushings and Hoisting Gear. Includes a set of wrenches, tooled up. Truck has approx. 25,000 Miles on it. SOLD
Rotary E-F - SRS #4471
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6; Engine: PTO; Mounted On: 1990 IHC; Truck Engine Make: DT 466; Condition: PRICE REDUCED; Tools/Options: Failing 1500: OPEN TO OFFERS! Retractable Drawworks, Heavy Duty Mast, Fabricated Table (can remove top plate to install surface casing), No Kelly Included, 42' Mast, Set up to Run 2-7/8" External Upset Drill Pipe with Lugs, Four Jacks. Truck has 188,419 Miles on it. Drill Rod, Slips to fit table and Two Older Parts Rigs Available for an Extra Cost.
Rotary E-F - SRS #4470
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5X6 with Air Clutch; Engine: PTO; Mounted On: 2006 Freightliner; Truck Engine Make: CAT C7; Condition: PRICE REDUCED; Tools/Options: Failing 1500: PRICE REDUCED! Fluid End on Mud Pump Needs New Liners and Pistons. Newly remanufactured Drawworks, All Retractable, Heavy Duty Mast, Heavy Duty Mechanical Breakout Table - Chain is Broken -Assembly C2201-D, 2-7/8" X 27' Long Kelly, 42' Mast, Sandline with 1/2" Cable. Rig is Set up to run 2-7/8" External Upset Drill Pipe with Lugs. Front and Rear Jacks, Operators Platform, Pipe Rack. Approx. 344,193 Miles on Truck. Drill Rod, Slips and Two Older Parts Rigs Available for an Extra Cost.
Miscellaneous - SRS #4547
DESCRIPTION: Engine: 2015 Cummins QSX15, 525 HP California Carb Compliant Engine; Mounted On: Trailer; Tools/Options: Engine odometer reads 900 hours.
Rotary E-F - SRS #4546
DESCRIPTION: 2012, Foremost; Model: DR 12/26P-60/24-900 DR24HD; Compressor: IR 900/350; Engine: PTO; Mounted On: Kenworth T800W; Truck Engine Make: Cummins ISXZ 525 HP; Tools/Options: Foremost DR 12/26P-60/24-900 Year 2012: DR 24HD, 80,000# Pullback with Upgraded 6" Cylinders and Mast Structure Reinforcement. Upgraded RC 150 High Torque, Topdrive 12,000 ft.-lbs., Auxiliary Winch with Swinging Jib, Line Oiler, 12 GPM CAT Water Injection, Drill is set up to run 4.5" reg drill rod. Lower Drive Upgraded to 1.4 Million in./lb. (originally 1 million in./lbs.) Tier 4 Engine, Jake Brake, Upgraded Cooling Package, 20K Front and 46K Rears. Torque Lower drive has been gone through and what needed rebuilt was, Tophead has also been rebuilt. New Hydraulic Pumps and Hoses, Plates in Lower Drive were Rebuilt. New Turbo on Truck Engine. $100K in recent M&R Includes 6" to 24" Jaws, Big 16" Diverter.
Sold - SRS #4545
DESCRIPTION: Smeal; Model: 4T; Engine: PTO; Mounted On: 2014 Ram 4500 2WD; Truck Engine Make: Hemi Gasoline; Condition: SOLD; Tools/Options: Smeal 4T: Truck has an Automatic Transmission. SOLD
Pump Hoist - SRS #4544
DESCRIPTION: 1969, Smeal; Model: 10T; Engine: PTO; Mounted On: 1994 Ford F750; Truck Engine Make: Cummins 230 HP; Tools/Options: Smeal 10T Year 1969: Truck has Air Brakes & a 5-Speed. 36' Mast, 8' Layback at 36'
Sold - SRS #4543
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 2007 Ford F450 4WD; Truck Engine Make: 6.0 L Power stroke Diesel; Condition: SOLD; Tools/Options: Smeal 5T: No Sandline, has the Plug for a Remote. Truck has a Power stroke Diesel and Automatic Transmission, approx. 66,000 Miles on it. Tailgate and Pipe Racks being put back on. SOLD
Sold - SRS #4542
DESCRIPTION: 1983, Dresser; Model: T70W; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: CAT 3406; Condition: SOLD; Tools/Options: Dresser T70W Year: 1983: 70K Pullback, Tophead Drive. Runs Range II Pipe, Rod Loader (can preload pipe), 12" Hydraulic Table (hydraulic, hinges up & dies are interchangeable), 4 Drums, 3 Winch Lines. Capable of Retrieving Core Barrels. One Front and Two Rear Jacks. Crane Carrier has some Rust. Had a CAT 4 Mast Inspection in 2014. SOLD
Sold - SRS #4448
DESCRIPTION: 2008, Flatwater Fleet; Model: 2,700 Gallon ; Mounted On: 2006 IHC 7400; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Flatwater Fleet 2,700 Gallon Year: 2008: SOLD (2) 110 Gallon Transfer Fuel Tanks all Redone and Painted. 20' Bed Space with Tool Boxes & Fuel Tanks in the Front, 2'6" Tall. Two Brand New Boxes on the Front and Two on the Back in 2024 and Repainted Box, New Lights on the Back with New Brackets, all Maintenance that was needed was also done at that time. Odometer Currently Reads 172,587 Miles, Allison Automatic Transmission (installed a few years ago), low miles on it. Truck is Kept Indoors. SOLD
Sold - SRS #4332
DESCRIPTION: 2008, GEFCO; Model: 30K; Compressor: 1000/350 Screw, Heavy Duty PTO with Clutch; Mud Pump: 4X3 Mission NEW; Engine: PTO; Mounted On: 2008 Peterbilt 367 6X4; Truck Engine Make: CAT C15 550 HP; Tires: New - Front; Condition: SOLD; Tools/Options: GEFCO 30K Year: 2008: SOLD Hydraulically Driven Mud Pump with Standard 2-1/2" Piping. (4) Hydraulic Leveling Jacks, Tophead Drive with 70,000 in-lb. Torque, 0-120 RPM, 2-11/16" Water/Air Course, Hydraulic Jib Boom with Dual Controls on Driller & Helper Side. Carousel Holds (6) Pieces of 4.5" X 20' Drill Rod, 2-7/8" IF Tool Joints with Top Breakout Wrench. Hydraulic Cylinder with Cable Pulldown Holdback. 25,000# Pulldown and 30,000# Pullback. Man Winch over Jib Boom, 25,000# Single Line Pull with 3/4" Cable. Line Oiler, 18 GPM Bean 4-Cylnder Hydraulic Powered Water Injection Pump. Single Rod Loader, Helpers Side for Loading Rod under Tophead, Hydraulically Powered Split Table Guide with Air Operated Holding Wrench, Hydraulically Powered 60" Breakout Wrench, Hydraulically Powered Rod Spinner. PL2 Auxiliary Winch with 100' of 3/8" Cable (2,000# capacity), Pipe Rack for 15 Pieces of 4.5" X 20 Drill Rod (slide on outside of pipe rack), (5) Operating Lights, Heavy Duty PTO for Compressor and Hydraulic Pump Drive with Clutch. Side Driller and Helpers Platforms. Truck has 22,000# Front Axle and 46,000# Rears, Fuller 18-Speed Transmission, (2) Fuel Tanks (70 & 150 Gallon), A/C, Jake Brake, Alcoa Aluminum Wheels. Includes approx. 640' of Drill Rod, Breakout Wrench, Lifting Plug, CAT Fuel & Oil Filters, CAT Engine Oil, Side Air Filters, Old Mud Pump that was Replaced (needs small weld patch). Recently changed fluids, filters. New batteries and some new hoses. Carousel Activator is not Working, needs Repaired. Mud Puppy Available for an Extra Cost.
Rotary G - SRS #3914
DESCRIPTION: 1975, Gardner Denver; Model: 2000; Mud Pump: GD 7-1/2" X 10"; Engine: PTO; Mounted On: 4-Axle Crane Carrier; Truck Engine Make: 400 Cummins; Tools/Options: Gardner Denver 2000 Year: 1975: 58' Mast, 10" Retractable Rotary Table, Air Clutches, Two Drum Machine, No Sandline, No Rod Rack, 4-1/4" or 4-1/2" X 38' Hex Kelly (needs confirmed), Rig is set up to run 30' Rod. Has a Large Gardner Denver Swivel that has been Rebuilt, 2 Wells since. Has a Winch on the Side for Oil Field Dogs. Also Includes 810' of 5" X 30' Drill Rod with 3-1/2" IF Threads (used on 6 wells) and a Rod Trailer that was Purchased New and has < 300 Miles on it. Can be sold without rod.
Mud Grout Pumps - SRS #4541
DESCRIPTION: Mud Pump: 2023 Gardner Denver 5X6 FXG 172; Mounted On: Unmounted; Condition: Never Used; Tools/Options: Gardner Denver 5X6 FXG 172 Year: 2023 New, Never Used Gardner Denver 5X6 Mud Pump.
Sold - SRS #4368
DESCRIPTION: 2009, Versa Drill; Model: 100NG; Compressor: 500/200; Mud Pump: Mission 250 Series 3X4X13 & a Failing 5X6 Duplex; Engine: PTO; Mounted On: 2009 Peterbilt; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Versa Drill 100NG Year: 2009: SOLD 40K Pullback, Hydraulic Jacks, Main Winch & Sandline Winch,11-Rod Carousel, 2 3/8” ID with FEDP Threads 3” OD X 20' Pipe, Mission 250 Series Centrifugal Mud Pump with a 4" Discharge and a 5X6 Failing Duplex Pump, Hydraulic Quick Connects to Swap Two Hoses and Switch Between the Two. Truck has a Jake Brake, Manual Transmission, AC, Three Toolboxes, Odometer Reads 367,668 Miles and 18,380 Hours. Includes 400' of 3" X 20' Heavy Wall Pipe (will have New Box Ends & Tool Joints Replaced), (2) Drill Bit Subs (1) 6-5/8" API Regular Box Fish Necked to 3" OD FEDP 2-3/8" Box with 2-7/8" Tool Joints for Breaking, (1) 4-1/2" API Regular Box Fish Necked Down to 3" OD FEDP 2-3/8" Box with Tool Joints for Breaking. Rebuilt Fabco 200 Transfer Case is Available for an Extra Cost (0 hours). EXTENSIVE LIST OF M&R AVAILABLE. SOLD
Sold - SRS #4050
DESCRIPTION: 2016, Atlas Copco; Model: TH-60; Compressor: 1070/350; Mud Pump: Removed; Engine: PTO; Mounted On: 2014 Peterbilt 367; Truck Engine Make: Cummins ISX 600 HP - FACTORY NEW; Tires: NEW 95%; Condition: SOLD; Tools/Options: Atlas Copco TH-60 Year: 2016: 40K Pullback 30K Pulldown, 4,400 ft.-lbs. Maximum Head Torque, 2-Speed Head Rotation, 18,000# Winch, Hammer Lubricator, 7-Rod Carousel, Rig is Set up to Run 4.5" X 20' Drill Rod with 2-7/8" IF Rod, Rod Box Holds 18 Joints of Drill Rod, Bean 25 GPM/750 psi Water Pump. Truck has Two Fuel Tanks (150 and 85 gallon), Jake Brake, 19-Speed Eaton Transmission 68,000# GVWR, 22,000# Front Axle and 46,000# Rears. 425/65R22.5 Front Tires and 11R22.5 Rears. Recent Repairs and Upgrades: Top Breakout Wrench, Two New Lift Cylinder Pins on Mast, FACTORY NEW Cummins Engine, Gearbox Replaced with Newer Style Nimco, Installed Sandline, Single Rod Loader, New Cables, Brakes, Tires, Rod Spinner, Controls & Gauges Gone Though, Repaired. New Carousel Installed and Rollers in Shaft were Replaced with the Big Rollers. New Main Head, New Swivels & Pins, New Carousel, Replaced Seals & Bearings in Gearbox on Bottom, New Table Bushings. Electrical Control Box was Replaced, Grounded, Dash Wires all Gone through. All Work was either professionally done or Parts were Purchased New. Drill Rod Available, Diverter Optional. Currently has 38,278 Miles, 1,086 Engine Hours and 4,913 Compressor Hours. SOLD
Water Truck - SRS #4305
DESCRIPTION: Water Truck; Mounted On: 1998 Volvo Auto Car; Truck Engine Make: CAT 3406E 475 HP; Condition: PRICE REDUCED; Tools/Options: 2,200 Gallon Tank that has been Sandblasted and Painted. 20' Bed, 200 Gallon Fuel Transfer, IMT 2020 Teathered Control Crane. Truck has an Eaton Fuller 8LL Transmission, Jake Brake, 46K Full Locking Rears. Runs Strong, Doesn't Burn Oil or Blow Smoke, Miles Unknown
Sold - SRS #4394
DESCRIPTION: 2002, Mobile; Model: B61HDX; Engine: 4BT Cummins; Mounted On: 1992 Ford F800 2WD; Truck Engine Make: Ford 7.8L 210 HP; Condition: SOLD; Tools/Options: Mobile B61HDX Year: SOLD 2002: 3L8 Moyno Water Pump, In/Out, Side to Side Wiggle Tail, Main, Auxiliary & Saf-T-Driver Winches, 3 Outrigger Jacks, 2 Swingout Auger Storage Racks. Truck has approx. 156,000 Miles on it. Tooling in Photos Included. SOLD
Mud Grout Pumps - SRS #4538
DESCRIPTION: Mud Pump: GASSO 1654C 5X8; Engine: Detroit 471; Mounted On: Skid; Condition: Rebuilt; Tools/Options: GASSO 1654C 5X8: 250 Gallon Diesel Tank. New Expendables Included but not Installed. Enclosed Chain in Box, Enclosed Chain from Engine to Pump. 5-Speed Transmission (high pressure, low fluid).
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |