Rigs
Auger - SRS #4531
DESCRIPTION: 1995, CME; Model: 55; Engine: Deutz 5-Cylinder; Mounted On: 2014 IHC SBA 4300 4X2; Truck Engine Make: Diesel; Condition: Working Rig; Tools/Options: CME 55 Year: 1995: 3,200# Mainline, (2) 1,800# Winch lines (fast/slow), Auto Hammer. Cathead is not mounted but available, (3) Jacks, Wiggle Tail. 3L8 Pump and Water Tank are both Trailer Mounted Making the Rig under CDL. Truck Odometer Reads 225,686. No Rod or Tooling Available. TEMPORARILY OFF MARKET
Sold - SRS #4370
DESCRIPTION: Flatwater Fleet; Model: 2,400 Gallon; Mounted On: 2008 IHC 7600; Truck Engine Make: CAT C13 410 HP; Condition: SOLD; Tools/Options: Flatwater Fleet: 2,400 Gallon Flatwater Fleet Flat Tank, 30' Remote Stellar Crane. (2) 100 Gallon Fuel Tanks on the Deck with a Transfer Pump & Numerous Tool Boxes. Truck has an 18-Speed Transmission, Air Ride Suspension and Both Seats have Air Ride, Jake Brake, Full Lockers, approx. 109,000 Miles on it. 18k Front and 46K Rears, 64K GVWR. SOLD
Sold - SRS #4510
DESCRIPTION: 1982, Speedstar; Model: SS 135 HD; Compressor: Yes, Developmental - To Be Confirmed; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 2006 IHC 7600; Truck Engine Make: Cummins ISX 15; Tires: New; Condition: SOLD; Tools/Options: Speedstar SS 135 HD Year: 1982: SOLD Hydraulic Drawworks Rebuilt 6-8 Years Ago, Painted approx. 5 Years Ago. Mud Pump Had Gear End Rebuilt Two Years Ago and Fluid End about 6 Months Ago (2025), 4-Part Kelly Line and 4-Part Trip Line. Newer 3-3/4" Fluted Kelly with Drive Bushings. Four Leveling Jacks and has Pulldowns. All Hydraulically Driven except for Air Clutches. Hydraulically Driven 8-1/2" Rotary Table Rebuilt a Few Years Ago, Chain Box Completely Rebuilt 4 Years Ago. New Motor 4 Years ago (2021) New Clutch and 8 Brand New Tires, New Tranny. Bearings out on the Air Compressor Drive Clutch, has all the parts, just needs rebuilt. New Gauge Cluster was Installed when Engine and Drill was Installed on the IHC Chassis. Includes 400' of 3.5" Flush Joint Drill Pipe with 2-3/8" IF Threads. Truck has an 8-Speed Transmission and approx. 200,000 Miles on it. Engine and Transmission has approx. 80,000 Miles since Engine and Clutch was Replaced. SOLD
Pump Hoist - SRS #4516
DESCRIPTION: 2024, TDH; Model: 6X2; Engine: PTO; Mounted On: 2024 Ford F600 4WD; Truck Engine Make: 6.7L Power Stroke Diesel; Condition: PUT BACK TO WORK - OFF MARKET; Tools/Options: TDH 6X2 Year: 2024: Two Line Machine, Remote. Power Stroke Diesel Engine, Extra Rear Springs, approx. 17,000 Miles on Truck, Subject to Change. All Aluminum Boxes, Three Leveling Jacks. Working Unit. No Mechanical Issues.
Rotary S - SRS #4410
DESCRIPTION: 1984, Speedstar; Model: SS 15 III; Mud Pump: 7-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: IHC Truck; Truck Engine Make: 8V92 Rebuilt; Tools/Options: Speedstar SS 15 III Year: 1984: Needs a Turntable and Turntable Transmission. Has a 10" Table, No Rod Rack. It was Drilling Irrigation Wells, has the Big Drawworks and Air Clutches. Detroit Engine was Rebuilt and Drilled One Well Since.
Rotary D - SRS #4291
DESCRIPTION: 1995, Driltech; Model: T40KW3 Long Tower; Compressor: 1160/350; Mud Pump: 5-1/2" X 8" Gardner Denver; Engine: Cummins K19 600 HP; Mounted On: 1994 CCC with Lift Axle; Truck Engine Make: Cummins 350; Tires: Good; Condition: Well Maintained; Tools/Options: Driltech T40KW3 Long Tower Year: 1995: 600 HP Deck Engine, Long Tower, Hydraulically Driven Mud Pump, 20" Table Opening. 2-Speed Tophead (0-50 rpm @ 120,000 in/lb. & 0-150 rpm @ 92,000 in./lb.), 2.25" Pulldown Chains, Mast has a 34' Stroke, Inner & Outer Carousels, each Carousel holds (6) 4.5" X 25' Rods. One Exception on the outer carousel, a surface collar sits in one of the rod pods, The top of the collar is the same as the 4.5" Drill Rods so no change needed there. The Bottom has a Larger Pod that Sits above the original rod socket so it can easily be removed to facilitate a regular 4.5" rod. Heavy Duty Pulldown, Upgraded to the 70,000# Pullback and Installed 7.25 cu/in Rotation Pump, Tophead is Heavier Duty than a Standard D40K, Built with High Ambient Cooling for Engine, Hydraulic & Compressor Fluids, Rated for 130° F Conditions. 25 GPM Injection Pump. Includes 275' of 4.5" X 25' Drill Pipe with 2-7/8" IF Threads, 23' Surface Collar, Mud Pit. Can be sold without mud pump.. Condition: Well Maintained
Sold - SRS #4530
DESCRIPTION: Chicago Pneumatic; Tools/Options: 500' of CP Style Drill Rod. 3.5" O.D. X 20'.
Auger - SRS #4177
DESCRIPTION: Ardco; Model: Super L Mini Buggy; Engine: PTO; Mounted On: Ardco Buggy; Truck Engine Make: 4-Cylinder Isuzu Diesel; Tires: New; Condition: Runs Great; Tools/Options: Ardco Super L Mini Buggy: NP 4-Speed Transmission, Rockwell TRRT-32-79 Transfer Case, Bumper Mounted, PTO Driven Ramsey 400-L Winch, 3-Stage Commercial Hydraulic Pump, 14' Lockable Mast, Hydraulic Hoist Drum, Rod/Auger Rack. This Unit is Currently set up for Auger Drilling but Could be Converted to Mud Rotary with the Addition of Swivel and Mud Pump (not included). Runs Strong and is Light and Fast. Easily Hauled and Mobilized. Recently had New Tires Installed, New Radiator, New Hub along with the Hydraulic Pump being Replaced and completely Cleaned & Replaced the Hydraulic Fluid.
Sold - SRS #3899
DESCRIPTION: 1989, Mobile; Model: B47; Engine: John Deere; Mounted On: 2009 Ford F450XL Super Duty 4X4; Truck Engine Year: 6.8L; Condition: SOLD; Tools/Options: Mobile B47 Year: 1989: SOLD Two Winches, 3L6 Moyno Pump, Cathead (new rope 2021), 16' Mast, has run up to 6" auger on it, 140# Safety Hammer, approx. 170K Miles on the Truck. Truck Recently had the Engine and Transmission Replaced. Lots of Tooling Included (drive cap, adapter, 10 joints of 5' AWJ, 9 joints of 2-1/4" Auger, plug, bit, cutterhead, bit spade, hoist plug, sampler, retainer basked, sampler shoe, 3" X 30" shelby tube with caps, sample extruder assembly). Also available for an extra cost, 30' of 2.5" solid stem augers with pins and catcher that are brand new and only use some of them once or twice. Was being used for Shelby Tube Work. SOLD
Sold - SRS #4529
DESCRIPTION: Model: 3T; Engine: 4-Cyl. Wisconsin; Mounted On: 1997 Ford; Truck Engine Make: Gas; Tires: Okay; Condition: Working Unit; Tools/Options: 3T: New Hydraulic Hoses, Valve Bodies Rebuilt, New Hoist Cable, Deck Mounted Wisconsin Motor, Power Hoists. No Sandline. Truck has approx. 78,000 Miles on it. No Rust.
Sold - SRS #4524
DESCRIPTION: Rosewall; Model: 2,500 Gallon; Mounted On: Unmounted; Condition: Good; Tools/Options: Rosewall 2,500 Gallon Unmounted: Stainless Steel Tank/Body, Multiple Tool Boxes, Bulk Gravel Box
Parts Tooling - SRS #4523
DESCRIPTION: Atlas Copco - EPIROC; Tools/Options: Blast Hole Drilling Rig Parts, some are Used/Like New and some are Surplus/New. Owner Believes the are for a L8 Rig and DHR Series Epiroc FlexiRoc.
Mud Grout Pumps - SRS #4522
DESCRIPTION: Mud Pump: Gardner Denver 5X6; Tools/Options: Gardner Denver 5X6 Air Operated Mud Pump. Used approx. 4 Times since Rebuild.
Steel - SRS #4521
DESCRIPTION: Tools/Options: Approx. 1,200' of Ingersoll Rand 3.5" X 20' with 2-3/8" Threads, Pin Down. Used Drill Rod
Sold - SRS #4463
DESCRIPTION: 2003, Ingersoll Rand; Compressor: IR 750/175; Engine: Cummins; Mounted On: Tag Along - Pull Behind; Condition: SOLD; Tools/Options: Ingersoll Rand 750/175 Year: 2003 Cummins: 1,566 Hours. SOLD
Sold - SRS #4519
DESCRIPTION: Montana Flat Tank; Model: 2,000 Gallon; Mounted On: 1996 Kenworth; Truck Engine Make: CAT C12; Condition: OFF MARKET; Tools/Options: Montana Flat Tank 2,000 Gallon: 2,000 Gallon Water Bed. Super 10 Transmission, 200 Gallon Fuel Tank. Truck has 879,000 Miles on it. Grouter Not Included. OFF MARKET
Rotary G - SRS #4515
DESCRIPTION: 2020, GEFCO; Model: 40K; Compressor: 1070/350; Mud Pump: 3X4 Centrifugal; Engine: PTO; Mounted On: Peterbilt; Truck Engine Make: Cummins ISX 605 HP; Condition: Great; Tools/Options: GEFCO 40K Year: 2020: 1,038 Hours on Compressor, 5,374 Hours on the Engine. No Carousel.
Sold - SRS #4513
DESCRIPTION: 1981, Ingersoll Rand; Model: T4W; Compressor: Sullair 900/350 with Clutch; Engine: CAT C15; Mounted On: CCC; Truck Engine Make: Cummins 855; Condition: SOLD; Tools/Options: Ingersoll Rand T4W Year: 1981: Reed R75 Mast and Topdrive, 70K Pullback. 4-Hole Funk Gearbox with Two Dennison Main Pumps, Swing and Extend Jib Boom, One Front and Two Rear Jacks, No Carousel. Compressor Clutch Adjusted in 2024 and Changed all the Fluids at the end of 2024. Includes 1,100' of 4.5" X 25' Drill Rod with 2-7/8" IF Threads and Breakout Flats on the Pin Side. SOLD
Sold - SRS #4511
DESCRIPTION: Model: 2,000 Gallon Amthor; Mounted On: 2001 Freightliner; Truck Engine Make: 500 HP CAT; Condition: SOLD; Tools/Options: 2,000 Gallon Water Bed, 200 Gallon Fuel Tank. Truck has an 8-speed Transmission. Truck Odometer Reads 769,752 Miles. SOLD
Compressors - SRS #4509
DESCRIPTION: Compressor: Sullair 900/350 Air End; Tools/Options: Sullair 900/350 Compressor Air End, was working fine when removed. Owner believes it has approx. 5,000 hours on it. Two other newer ones available for an extra cost but they need some repairs and or reassembled.
Sold - SRS #4508
DESCRIPTION: 2006, Smeal; Model: 6T; Engine: PTO; Mounted On: 2006 Freightliner; Truck Engine Make: CAT C7; Condition: SOLD; Tools/Options: Smeal 6T Year: 2006: Truck has approx. 150,000 Miles on it, Motor was Rebuilt within the Last Few Years. Truck GWV 25,550, Lots of Tool Boxes SOLD
Rotary G - SRS #4132
DESCRIPTION: Gardner Denver; Model: 1500; Mud Pump: 5X10; Mounted On: 1976 +/- 4-Axle CCC; Truck Engine Make: Cummins; Condition: Being Reconditioned; Tools/Options: Gardner Denver 1500: Big Kelly (4-1/2" - 5" to be confirmed), Mast is at Least 38', Rig can Handle 34' Pipe Retractable 10" Table, Leveling Jacks, Air Clutches on Drawworks, Sand Reel and Air Clutches.
Sold - SRS #4105
DESCRIPTION: 2022, Hunke (Smeal); Model: 4T; Engine: PTO; Mounted On: 2022 Ford F550 4WD; Truck Engine Make: 6.7 L Diesel; Condition: SOLD; Tools/Options: Hunke 4T Year: 2022: Hoist has a 2,000# Single, 4,000# 2-Part Line and 6,000# 3-Part Line Capability, Front Jack, Wire Winder, Wireless Remote, Hydraulic Oil Cooler, (2) Tilting Pipe Racks, Mast Lights, Hi-Low Speed for Winch, run by PTO off Transmission. Truck has a 9' Aluminum Utility Body with Flip Top Boxes with Lighting in all Boxes, Draw Assembly, Automatic Transmission, Loaded with Power Everything, Backup Camera and approx. 5,500 Miles on it and a Draw Assembly. SOLD
Sold - SRS #4507
DESCRIPTION: Shop Built; Model: Grouter; Engine: 20 HP Kohler; Mounted On: 20' Tandem Trailer; Condition: SOLD; Tools/Options: Shop Built Grouter Continuous Grouter: 20 HP Kohler Commander V-twin Engine with Tandem Hydraulic Unit. Dedicated Circuit for Grout Pump. 400' X 1" Reel, Moyno 2L6 Food Grade Pump capable of up to 45 GPM, currently using 1" Poly Pipe on the reel so approx. 20 GPM is more Accurate. Capable of mixing, pumping and retracting hose all at the same time. 14,000# Trailer with New Axles. Includes Ramps and Hydraulic Power Unit and Grouter can be Separated. SOLD
Sold - SRS #4295
DESCRIPTION: 1978 or 1979, Simco; Model: 5000; Compressor: Developmental; Mud Pump: 3X4X13; Engine: PTO; Mounted On: 2020 IHC Single Axle; Truck Engine Make: Cummins; Condition: SOLD; Tools/Options: Simco 5000 Year: 1979 or 1980 Simco, Manual Available. Mono Derrick, 20' Rod Rack, Single Axle Truck under CDL, Truck has approx. 105,000 Miles on it. New Planetary Pulldown for Hydraulic Motor, New Hydraulic Head Motor, Some New Hoses, Bearings Replaced, New Gauges in Console, Four Hydraulic Outriggers, Hydraulic Breakout Wrench, 6-Speed Eaton Fuller Manual Transmission. SOLD
Sold - SRS #4506
DESCRIPTION: 1998, Reichdrill; Model: T-690W; Compressor: 1050/350; Mud Pump: Plumbed - See Below; Engine: CAT 3406B; Mounted On: 1998 Mack; Truck Engine Make: Mack 350 HP; Tires: See Below; Condition: SOLD; Tools/Options: Reichdrill T-690W Year: 1998: SOLD REWORKED! Rapid Retract, 44,000# Pullback, 5" Cylinders, 140# Chains, 22" Table Opening, 6-Pod Carousel, Rebuilt Compressor (2017) approx. 1,350 Hours Since. Low Hours, Head Rebuilt in 2015, New Cooler (zero hours), New Separator Filter (10 hours), New Hercules Controls & Butterfly. 2020 New Motor for Water Injection, Deck Engine Rebuilt in 2019 approx. 1900 hours since, New Starter & Batteries, Deck Engine Battery Box Lid, Front & Left Rear Jack Pads New, Engine Heaters on both Engines. Replaced Ball Grip from A35 Control Handle, (4) Linkages on A20 Valve Bank Replaced, All Handles & Linkages on Triple Sub Plate Replaced, Water Injection 0n/off Control Replaced, Holdback Disengage Control Repaired, Holdback Pressure Gauge Replaced, Downhole Air Gauge Replaced, Rotation Gauge Replaced, Air Compressor Oil Injection Gauge Replaced, Tail Blowdown Cylinder Repacked, Tail Blowdown Cylinder Replaced, Hydraulic Tank Supercharge Gauge Replaced, Downhole Air Valve Hydraulic Cylinder Replaced, Deck Engine Hour Meter Replaced after Engine was Rebuilt. New 8 GPM Bean Water Pump, Guard over Chain Drive on Water Injection Pump, Knob on Fan Control Replaced, Barrel Loader Swing Cylinder Repacked, 3 Hydraulic Pump Replaced, Pump Gearbox Breather Replaced. Rear Clearance Light Bar on Truck Replaced. Fast Up-Pull Valve & Piston Pump Replaced. 2015 Bearing in Head was Replaced. Truck has approx. 58,000 Miles on it, an Eaton Fuller 8-speed Transmission + Low and Low/low, 3 Ranges in Reverse and 3 Ranges in Low. Jake Brake, 4.42 Rear-end Ratio. New Transmission and Clutch, New Drive Tires (8 total less than 300 miles), Steer Tires have about 3,000 Miles, New Windshield, Batteries, Driver side Seat and Power Steering Hoses have been replaced. Drill has had all Cylinders Rebuilt except for the Jacks, all Controls Rebuilt, Replaced 85% of all Hydraulic Hoses, Replaced Air Lines, Setup Filtered & Regulated Auxiliary Air off of Rig Compressor to run a Diaphragm Pump, Air Cylinder etc., Resealed Tophead. Rig can carry 260' in Rod Box and another 120' in Carousel. No Helper Controls, has a Catwalk and Platforms. Rig is Set Up to Run 4.5" Drill Pipe. 740’ of Near New 4 ½” x 20’ x 2 7/8” IF. Drill Rod Available for an Extra Cost. SOLD
Sold - SRS #4479
DESCRIPTION: 2003, Schramm; Model: 450WS; Compressor: Sullair 900/350; Engine: CAT 3406 465 HP; Mounted On: 2004 Sterling 9500; Truck Engine Make: Mercedes 410 HP; Condition: SOLD; Tools/Options: Schramm T450 WS Year: 2003: SOLD! 25' Stroke, 20 GPM Water Injection Pump, Jib, 15-Pod Carousel, 4 Outriggers, 2 Behind Cab, 2 at Rear of Rig, Braden 15,000# Winch. Rig is set up to run 3.5" OD Drill Rod. 30K Pullback, 17K Pulldown. Compressor was Rebuilt in 2017. Compressor has approx. 1800-2000 Hours Since Rebuild. Deck Engine has approx. 10,000 Hours. Doesn't use oil but has a small oil leak behind the fuel pump. Dust Collector was added in 2010. Tophead was also Recently Replaced. Has been mostly used for Geothermal Drilling with a DTH bit. Truck has a Fuller Transmission. Includes 15 Drill Rods. Last drilled Feb-March 2025.
Sold - SRS #4346
DESCRIPTION: Smeal; Model: 3T; Engine: 6.7L Diesel; Mounted On: 2018 Ford F-350 4WD; Condition: MOTIVATED TO SELL!; Tools/Options: Smeal 3T: PRICE REDUCED Mast Extends about 6', Sandline. Truck has approx. 135,000 Miles on it.
Sold - SRS #3811
DESCRIPTION: Jaswell; Model: 3500; Compressor: 900/350; Engine: 12V92; Mounted On: Paystar 5000; Condition: SOLD; Tools/Options: Jaswell 3500: 1,000' of Drill Pipe Included. A pipe Trailer is Available for an Extra Cost.. SOLD
Rotary G - SRS #3904
DESCRIPTION: 2015, GEFCO; Model: Stardrill 300 HD; Compressor: 1000/365 Atlas Copco Rotary Screw; Mud Pump: GD FXG 5X6 Duplex; Engine: PTO; Mounted On: unmounted; Tools/Options: GEFCO Stardrill 300HD Year 2015: Unused Bare Rig. Rig is missing main Power Take Off Box. Direct Circulation Rig with Mud and Air Drilling Applications. 24,000# Pullback, Gear Type Heavy Duty PTO Power Gear,, 4 Hydraulic Jacks, 12" Square Tube Mast with 60,000# Capacity, 36'6" Free Height under Jib (can handle 4.5, 6.0 or 24.5 Meter Rods at a time). 3-Cylinder Water Injection Pump, Downhole Hammer, Single Pipe Loader, Pipe Spinner and Breakout Wrench. Rig is missing the following: PTO Assembly, Derrick Raising Cylinders, Derrick Pin, Mud Pump Liner Cap, Breakout Wrench, Winch Pump, Pulldown Pump Rotary Pump, Oil cooler Pump, Cylinder Circulation Pump, Controls Pump, Compressor Clutch Assembly, Throttle Controller.
Compressors - SRS #4504
DESCRIPTION: 1993, Ingersoll Rand; Compressor: 900/350; Condition: Working when Removed; Tools/Options: Ingersoll Rand Year: 1993: Was Removed from a 1993 Ingersoll Rand Drilling Rig. Approx. 16,000 Hours.
Compressors - SRS #4503
DESCRIPTION: 2006, Atlas Copco; Compressor: 1070/350; Condition: Was Working When Removed; Tools/Options: Atlas Copco Year: 2006: Compressor was removed from a 2006 Atlas Copco drill. Approx. 9,500 hours.
Rotary A-B - SRS #4501
DESCRIPTION: Turnkey Water Well Drilling/Well Treatment Install/Service Business, Condition: Operating Business; Tools/Options: Profitable, Turnkey Water Well Drilling and Water Well Treatment System Service/Install Business for Sale. Years in Business with Existing Customers in both the Water Well Drilling Side and Water Well Treatment Systems. Includes Business Name, Phone Number, Customer List and Equipment. Equipment in Excellent Condition. Including but not Limited to Drilling Rig, Water Truck, Service Trucks, Skid Steer, Inventory. More information Available to Serious & Qualified Buyers.
Compressors - SRS #4500
DESCRIPTION: 2006, Atlas Copco; Model: XAS756; Compressor: 750/100; Engine: CAT; Mounted On: Tag Along Pull Behind; Condition: Runs and Works Well; Tools/Options: Atlas Copco XAS 750 Year: 2006: Hour Meter Shows 6,252Hours. Runs and Works Well, Small Oil Leak at the Rear. Recently Gone Through by CAT Dealer.
Rotary D - SRS #4496
DESCRIPTION: 1979, Driltech; Model: D40K; Compressor: 750/300 (rebuilt in 2024); Engine: CAT 3406; Mounted On: 2005 Kenworth; Truck Engine Make: CAT C15 475 HP; Condition: Tooled up, Working Drill; Tools/Options: Driltech D40K Year: 1979: Rebuilt in 2016, Owner believes the Compressor was Rebuilt in 2024. No Carousel, 40K Pullback 26,500 Pulldown, set up to run an Atlas 2000 Casing Hammer which is Included, runs 4.5" O.D. X 20' Drill Rod. Truck has approx. 21,800 Miles and an 18-Speed Road Ranger Eaton Transmission. Includes a Tooled up 1997 Volvo Service Truck with approx. 231K Miles, approx. 200' of Used Drill Rod and (4) New Drive Shoes. Maintenance Records Available upon Request. Entire Business can be Purchased also, no Land or Buildings Included
Sold - SRS #4480
DESCRIPTION: Geo-Loop; Model: 50-500; Engine: Honda; Mounted On: Skid; Condition: SOLD; Tools/Options: Geo-Loop 50-500: Includes Hose Reel. SOLD
Sold - SRS #4494
DESCRIPTION: Smeal; Model: 5T; Engine: PTO; Mounted On: 2008 Ford F350 4WD; Truck Engine Make: Gas V10; Condition: SOLD; Tools/Options: Smeal 5T: No Remote but has a Plug for one. No Sandline. Hoist has a little rust on it. Drives Good. SOLD
Truck - SRS #4475
DESCRIPTION: Mounted On: 2009 Peterbilt 365; Truck Engine Make: CAT C13 Acert; Tools/Options: 15-Speed Transmission, 4:11 Gears, 3 Axle. Odometer Currently Reads 29,765 Miles and 2,819 Hours. Was used to Pull a Lowbed Trailer. 3 Trucks Available. Two with Day Cabs and one with a Small Sleeper Cab.
Steel - SRS #4492
DESCRIPTION: Condition: Never Used; Tools/Options: 19 Joints on New, Never Used 3.5" O.D. X 20' Drill Pipe with 2-3/8" Threads. Also Available 40' X 6" Used Drill Collars and Subs for the Drill Pipe
Sold - SRS #4467
DESCRIPTION: Bucyrus Erie; Model: 22W Series II; Mounted On: Trailer; Condition: SOLD; Tools/Options: Bcyrus Erie 22W Series II: Some Tools Included. SOLD
Rotary H-I - SRS #4466
DESCRIPTION: Ingersoll Rand; Model: TH-55; Mud Pump: 4X3 Centrifugal; Engine: PTO; Mounted On: 1997 Ford; Truck Engine Make: CAT 3306; Tires: Good; Condition: Good - PRICE REDUCED!; Tools/Options: Ingersoll Rand TH-55: PRICE REDUCED! Driller & Operator Platforms, One Front and 2 Rear Jacks, Cable Pulldown, Rod Box Includes 640' of 3.5" Drill Rod, 15' Collars, Various Roller Bits and Drag Bits, 5" & 6" Air Hammers with Various Bits. Working Condition, All Controls & Drawworks are Functional. Machine has Minor Hydraulic Leaks but Overall Good Shape.
Rotary D - SRS #4349
DESCRIPTION: 1977, Driltech; Model: D40K; Compressor: 750/350; Mud Pump: GD 5X6 Air Driven; Engine: 3406C; Mounted On: CCC; Truck Engine Make: 350 Cummins; Tires: Good; Condition: Ready to Work; Tools/Options: Driltech D40K Year: 1977: Fresh Paint, Dual Carousels, Set up to Run 25' Drill Pipe, Approx 600 Hours on Deck Engine. Stacker Valves Replaced. Includes 300' of Drill Pipe and Breakout tools. Not Sure of Compressor or Carrier Engine Hours. Maintenance Records Available.
Rotary S - SRS #4491
DESCRIPTION: 1982, Schramm; Model: 685 DH; Compressor: See Below; Engine: 12V71 Twin Turbo; Mounted On: GMC; Truck Engine Make: 6V53 Turbo; Tools/Options: Schramm 685 DH Year: 1982: Last used in approx. 2024. Compressor wasn't used at that time, auxiliary air was used. On board compressor wasn't working, owner thinks it has a bad bearing. Compressor on Drill is a GHH 1000/350 - to be confirmed. Parts Rigs, Hurricane Booster and Wagon Style Sullair 900/350, Auxiliary Sullair Air Compressor Mounted on a Mack Truck with Hurricane Booster and approx. 2,200' of Schramm 25' Pipe with 3.5" API Regular Threads Available.
Sold - SRS #4264
DESCRIPTION: 2014, Atlas Copco; Model: T3W; Compressor: 1070/350; Engine: PTO; Mounted On: IHC Navistar; Truck Engine Make: Diesel; Condition: SOLD; Tools/Options: Atlas Copco T3W Year: 2014: Currently has approx. 3,800 Rig Hours and approx. <3,000 Compressor Hours, 40K Pullback, <18,665 Miles. Working Drill so Hours will Change. Bean Water Injection Lubricator, Single Rod Loader, Rod Spinner. Includes approx. 500' of 4.5" Rod with 2-7/8" IF Threads so a Murphy Plug can be used. Also Includes Basic Operating Tools, no Hammers. Serviced and repaired by an Epiroc Mechanic since New. SOLD
Sold - SRS #3802
DESCRIPTION: Canterra; Model: CT-350; Engine: PTO; Mounted On: 1989 Ford F-700; Truck Engine Make: DT 466; Condition: SOLD; Tools/Options: Canterra CT-350: SOLD Rod Rack and Plumbing for Rotary Option, Brand New Hydraulic System Installed in Early 2019 (only drilled 6 wells since). Main Line and Sand Line with Free Fall and Spudder Option (used to drive wells in). Longer, One Piece Mast, Lot of Torque., Auger Rack on Driver's Side, Rod Rack and Tool Box on Passenger Side. 5-Speed Transmission with 2-Speed Rear. SOLD
Sold - SRS #4488
DESCRIPTION: 1998, Pulstar; Model: P20; Mounted On: 1999 Ford Super Duty 2WD; Truck Engine Make: 7.3 L Diesel; Condition: SOLD; Tools/Options: Pulstar P20 Year: 1998: 3-Lines, 20,000#. Truck has a 6-Speed Manual Transmission, Currently shows 300,000 Miles. SOLD
Sold - SRS #4486
DESCRIPTION: 1987, Driltech; Model: D25KW; Compressor: 825/350 GHH; Engine: CAT 3406; Mounted On: Ford L8000; Truck Engine Make: Ford 240 Diesel; Condition: SOLD; Tools/Options: Driltech D25KW Year: 1987: CAT Deck Engine Replaced along with a Refurbished Intercooler and Head. CAT Rebuilt the Turbo in 2015. Brand New Cooler Hyd./Compressor 2016, Fuel Tank Removed, Flushed and Cleaned for Deck Engine, All Fluids and Filters Services, New Air Hoses, New Shutoff Solenoid, New Batteries, FMC Water Injection Pump, Hammer Lubricator, 6-Rod Carousel, 35,000# Pullback. Truck has a 13-Speed Road Ranger Transmission and approx. 60,000 + Miles, Engine was Overhauled in 2007. SOLD
Sold - SRS #4460
DESCRIPTION: 1998, Smeal; Model: 3T; Engine: PTO; Mounted On: 2021 Ram 4WD Single Cab; Truck Engine Make: Cummins Diesel; Tools/Options: Smeal 3T Year: 1998: SOLD Solid Unit with a Little Surface Rust. Main Line Winch and Sand Line, Remote Control for Winches. Truck has an Automatic Transmission and approx. 75,000 Miles, Near New. SOLD
Sold - SRS #4377
DESCRIPTION: 2006, Atlas Copco; Model: T3W DH 55K Pullback; Compressor: IR 1070/350 HR 2.5 with Clutch; Engine: CAT C15 565 HP; Mounted On: 2007 IHC Paystar (Navistar); Truck Engine Make: CAT C13 380 HP; Condition: SOLD; Tools/Options: Atlas Copco T3W Deephole Year: 2006: SOLD 7,600 Original Hours. 55K Pullback, Heavy Duty Reinforced High Strength Steel Double Frame Full Length of Chassis. 4 Hydraulic Outrigger Stabilizer Jacks. Over Pressure Control System on Jacks. 4 Motor, High Torque - High Speed Tophead Drive, 35' Tower with 2 Retract Positions so Hammer can be Retracted while Installing Casing, 20" Hydraulic Open & close and Swinging Open & Close Access to the Centralizer Bushings. Air Operated Table Breakout Wrench and Air Operated Retract Access Gates. Hydraulic Powered Breakout Wrench, 7-Rod Carousel set up for 4.5" Diameter Drill Pipe Table Opening, 18" Bare Drum, Single Line Hydraulically Powered Main Winch. 2-Stage Oil Flooded Screw Compressor. 1800 RPM 565 HP High Duty Cycle Industrial C15 Engine. In-Out Box Disconnect Device between Engine & Compressor. 20 GPM Water Injection with Variable Speed Control, Jib Boom for Main Winch Line with Dual Controls, Swing and Extend Capabilities, Single Rod Load & Rod Storage Box, Under Deck High Capacity Fuel Tank for Deck Engine, Under Deck Tool Box. 500' Rod Storage (25 pieces of 4.5" X 20' Cyclone Style Flush Joint Pipe) Truck Odometer Reads 3,248 Miles and 3,533 Engine Hours. Will Include some Used Drill Pipe and a Used 6" & 8" Hammer. Tophead was Replaced with a Rebuilt one by Previous Owner. SOLD
Sold - SRS #4348
DESCRIPTION: 1978, Driltech; Model: D40K; Compressor: Sullair 750/350 Rebuilt; Mud Pump: GD 5X6 Rebuilt Fluid End; Engine: CAT 3406 Rebuilt; Mounted On: CCC; Truck Engine Make: CAT 3406C - 400 HP Rebuilt; Condition: SOLD; Tools/Options: Driltech D40K Year: 1978: SOLD Dual Carousels, Rebuilt Engine Installed, approx. 1,103 Total Hours on it. Engine in Carrier has approx. 2,488 Hours Since Rebuild. Factory Rebuilt Sullair Compressor has approx. 5,415 Hours. Has a few Leaks/Drips. Includes 1,000' of 4.5" X 25' Drill Pipe and Breakout Tools. Fluid End on Mud Pump Rebuilt Last Job. Brand New Tires on Rear. Maintenance Records Available. Ready to Work !!
|
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 |
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 |