Rotary P-Q

Search:
SRS#:
Category:
Keyword:

Rotary P-Q - SRS #3460

DESCRIPTION: 1985, Portadrill; Model: 524/741; Compressor: Atlas Copco; Mud Pump: 5-1/2" X 8" Gardner Denver; Engine: PTO; Mounted On: 1985 IHC 2674; Truck Engine Make: DT 466; Tires: New; Condition: Good; Tools/Options: Portadrill 524/741: 7.5" Table with Bushings to 5", 38' Mast (capacity estimated at 40-60,000#), Compressor is 450 CFM on 55 psi and 325 CFM on 125 psi, Rod Rack,4 Hydraulic Jacks, 2" Swivel, Double Blocked., 5X4 Transmission, New Pinion & Ring Gear in Drawworks, New Brake Bands, Rebuilt Table, Bushings in all Levers on Control Console, New Metal in each Side of Rig, Driller's Platform, New Hydraulic Bank on Driller's Console, New Paint, Mud Pump Oiler. Parts Book Available.

Rotary P-Q - SRS #3373

DESCRIPTION: 1974, Portadrill; Model: 10TG600; Compressor: Atlas Copco DT4 715/125; Mud Pump: Failing 5X6; Engine: Detroit 6V71; Mounted On: Crane Carrier; Truck Engine Make: Cummins 8.3L; Tires: Good; Condition: Ready to Drill; Tools/Options: Rig is set up for water well drilling. Fully Tooled and Ready to Drill. Noster Gear Tophead with 3" King Swivel. 30,000# Pulldown, Double Drum 2-Part 5/8" Drawworks for Casing Line/Tophead with Brakes. Rod box, and Auto Carry Out. Breakout Table, CAT Triplex Water Injection, 3" Versa-Matic Diaphragm Grout Pump, 250 Gallon Fuel Tank, Locking Hydraulic Jacks, Owner has been down to 650', Drilled 22" Holes. Tool & Block Storage Area. Carrier has Hendrickson Rear Suspension, 13-Speed Transmission. Includes Tooling, Mud Pit, (11) Pieces of 4.5" X 2-7/8" IF X 25' Drill Rod, 6" OB Stabilizer, Casing Clamps, Petol , Parts Manual.

Rotary P-Q - SRS #3340

DESCRIPTION: 1952, Portadrill; Model: Winter Weiss ; Compressor: None; Mud Pump: 5X6; Engine: 250 Chevy 6-Cylinder; Mounted On: Trailer (Includes Truck - see below); Tires: Bias; Condition: Working Drill; Tools/Options: Portadrill Winter Weiss: Mast is approx. 20' in Length from Table, Hydraulic Pulldown, Breakout, Sandline, Table is Non-Retractable and Capable of Dropping 4" Casing through it., (2) Hydraulic Leveling Jacks up Front. Includes Mud Tub, Desanding Cone, approx. 400' of Portadrill 15' Drill Rod with 2-7/8" Threads and some Bits. The Truck that is used to pull it is a 1973 IHC Transtar Powered by a 318 Detroit Engine with approx. 380,000 Miles. Truck has a Square 1,850 Gallon Water Tank on Deck. Truck is Road Worthy and runs but will need New Tires soon.

Rotary P-Q - SRS #3330

DESCRIPTION: 1968, Portadrill; Model: 10 TG; Compressor: 500/125; Mud Pump: 3X4 Mission; Engine: Detroit 671; Mounted On: 1968 IHC; Truck Engine Make: Gas; Tools/Options: Portadrill 10 TG: 35' Mast, 4-1/2" Kelly, 7-1/2" Retractable Table, 8" Twin Disk Clutches, Bean Injection Pump, Double Drum. Compressor has approx. 5,000 Hours or Less on it. Secondary Sandline Winch is Disconnected. Ran good up until the time it was parked in Sept. 2017. 270' or more of 4.5" Drill Rod with 2-7/8" IF Threads and Lift Plugs available.

Rotary P-Q - SRS #3219

DESCRIPTION: Portadrill; Model: TK 505; Compressor: None; Mud Pump: See Below; Engine: John Deere (runs mud pump); Mounted On: 1995 Volvo White; Truck Engine Make: CAT 3126; Condition: Working Drill; Tools/Options: Portadrill TK 505: 40' Mast, Kelly is approx. 5" X 30', 2-1/2" Swivel, 8.5" Retractable Table, Mechanical Clutches, Table and Winches, Double Drum (Main Line & Sand Line) New Kelly Bushing & Turntable. Stand alone 3X4 Mission Mud Pump, Rig is set up to run 4" O.D. X 20' X 3.5" IF Thread Drill Rod with 5" Tool Joint. Approx. 300' +/- Rod Included. Deck Engine Runs Mud Pump. Owner Believes Portadrill is late 1960's. Truck has approx. 60,000 Miles on it. Working Drill.

Rotary P-Q - SRS #3252

DESCRIPTION: 1979 to be confirmed, Quickdrill; Compressor: None; Mud Pump: Centrifugal; Engine: PTO; Mounted On: 1984 or 86 Kodiak GMC Truck; Truck Engine Make: Diesel; Tools/Options: Quickdrill: Two Winches, Single Rod Loader Included but not on the Drill. Includes Mud Tub and some 2-7/8" X 10' Drill Rod, Flush Joint. Right Rear Jack Leaks.

Rotary P-Q - SRS #3195

DESCRIPTION: 1979, Portadrill; Model: 524; Compressor: LeRoi 256S2; Mud Pump: 5-1/2" X 8"; Engine: PTO; Mounted On: 1996 Kenworth; Truck Engine Make: Cummins; Condition: Fully Overhauled; Tools/Options: Portadrill 524 : Fully Overhauled, Rig has New Frame Skirting. 7-1/2" Retractable Table, 3-Drum Machine Including Sand Line, 4-1/2" X 24' Kelly, 50' Mast 400' of 4" Drill Rod & Stabilizer available for an extra cost. Truck has a Tag Axle. 1990 Autocar 2,000 Gallon Water Truck with 360 Cummins Diesel also Available. Truck has <160,000 Miles.

Rotary P-Q - SRS #3123

DESCRIPTION: 1972, Portadrill; Model: 522; Compressor: None; Mud Pump: 5-1/2" X 8" Gardner Denver - Newer Gear End; Engine: PTO; Mounted On: 1984 Autocar; Truck Engine Make: CAT 3208; Tools/Options: Portadrill 522: 36' Mast, 7-1/2" Retractable Table (16" Opening?), Bailing Drum, 3-1/2" X 24' Fluted Kelly, 2" Swivel, 45,000# Pullback, 3-Part Line. Hydraulic Pulldown, Jacks, Mast. Mechanical Winches & Table. New Pins & Bushings in Pulldown Sprockets under the Truck, New Pinion Bearings in Rotary Table, Rotary Table has been Rebuilt. Includes Approx. 480' of 2-7/8" X 20' Rod with 2-3/8" IF Threads, 12" Wing Bit.

Rotary P-Q - SRS #3041

DESCRIPTION: Portadrill; Model: TKS-408; Compressor: None; Mud Pump: None; Engine: 8V92TA; Mounted On: 1978 International F5050; Truck Engine Make: CAT 3208; Condition: Fair; Tools/Options: Portadrill TKS-408: 38' Derrick with a 2.5" Portadrill Swivel and a 4.5" Fluted Kelly. Also has a 53' Derrick with a 3" King Oil Swivel Recently Rebuilt. Rig is set up for Reverse Air Drilling with a 4.5" Square Kelly - 4.5" Xhole Connection. Rig comes with 690' of 4.5" X 30' Drill Rod with 4.5" Xhole Connections, (1) 9.5" X 30' Spiral Collar with 7-5/8" Reg. Connection, (1) 6.5" X 20' Smooth collar - 4.5" Xhole Connection, (1) 18" Sealed Bearing Hole Opener with 7-5/8" Box up X 7-5/8" Pin Down, (1) 13" Sealed Bearing Hole Opener 7-5/8" Box Up X 4.5" Reg. Box Down, (1) 7-7/8" Sealed Roller Bit, (1) 11-7/8" Rerun Bit Skirted & Cut Out for Reverse Air, (1) New 4.5" Xhole Box by 7-5/8" Pin Sub, (1) New 7-5/8" Box by 6-5/8" Box Sub. All Bit have only drilled 180'. Back of Truck has been modified to 36" opening - no pulldown. Hydraulic Cylinders Need Repacked, Unit needs Paint. All Hydrostatic Hoses were changed in Feb. 2016. Drill can be purchased without rod and tooling for a lesser cost. Tooling can also be purchased separate from drill.

Rotary P-Q - SRS #2788

DESCRIPTION: 1970's, Quickdrill; Model: QM 300; Compressor: Joy 225/125; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 1997 IHC 2WD; Truck Engine Make: DT 466; Condition: Refurbished Working Drill; Tools/Options: Quickdrill QM 300: REFURBISHED. Drill is a Late 70's Quickdrill that has been upgraded with all New Hydraulics & Control Panel in 2002. Hour Meter Reads 507 Hrs., not sure if it is Working Properly. Drill was Reconditioned, Complete - Fresh Long Block Engine with approx. low Hrs. on Rebuild. Odometer Reads approx. 356,470 Miles. Compressor needs Bearings. 6 Hydraulic Cylinders Replaced in 2015/2016 along with being Sandblasted & Painted. Dual Motor Tophead, 7,500# Main Winch with Jib, Break-Out Wrench (Swedged Cable), 3" Diaphragm Pump (Behind Cab), 4-24" Stroke Leveling Jacks, Pipe Rack for 360' Mayhew Jr. Rod, Pipe Loader, Driller Platforms with Center Section. Drillmaster Deck & Controls, Square Quickdrill Mast, Truck has a 7-Speed Transmission and Air Brakes. Includes: 1 Tophead Sub with Pusher Plate, 1 Loader/Hoist Plug, 1- 6" Square Center Table Bushing.

Rotary P-Q - SRS #3024

DESCRIPTION: 1980, Portadrill; Model: TLS 472; Compressor: 850/350 Sullair; Mud Pump: None; Engine: Detroit 8V92 Remanufactured Installed 2016; Mounted On: 1980 Ford 8000; Truck Engine Make: CAT 3208; Tools/Options: Portadrill TLS 472: PRICE REDUCED! Remanufactured Deck Engine Installed in 2016. Mast is approx. 29', 40,000# Pullback, Holte Casing Hammer, Compressor Disconnect Clutch, Retractable Rotary Table Opens to 16", 2" Air Swivel. Rig is set up to Run 4-1/2" X 20' Drill Rod. No Rod or tooling Included. Compressor Hours Unknown but Estimated to be Approx. 8,000 +/-, Truck Miles Unknown.

Rotary P-Q - SRS #2910

DESCRIPTION: 1978, Portadrill; Model: TKS; Compressor: 750/250 Screw; Mud Pump: Trailer Mounted Mission available; Engine: 8V92 (Recently Rebuilt); Mounted On: 1979 International Paystar; Condition: Runs Good; Tools/Options: Portadrill TKS: (Hour Meter does not Work). 7-1/2" Retractable Table, Retracts to 12" - 16". 4-1/2" NEW Kelly, Bean Injection Pump, (3) Rebuilt Leveling Jacks, Hammer Oiler. Trailer Mounted Mission Centrifugal Mud Pump Powered by a CAT 3208 available for Extra Cost. Also Available for an Extra Cost: 600' of 4-1/2" X 15' Flush Joint Drill Rod. Many Spares Available including a Swivel, Kelly, Hydrostatic Pump. Owners Manual Available. Water Separator and hi/low Switch for Compressor Needs Repaired. Can Switch Manually at the Compressor. Call for Pricing of Rig with Rod and Tools.

Rotary P-Q - SRS #2850

DESCRIPTION: Portadrill; Model: 10TKT; Compressor: None; Mud Pump: 7-1/2" X 10" Centerline; Engine: PTO; Mounted On: 1995 International; Truck Engine Make: CAT 3406B 425 HP; Condition: Working Drill; Tools/Options: Portadrill 10TKT: 53' Mast, Tophead Drive, Centerline Mud Pump, (2) Front and (2) Rear Jacks. Transfer Case has been Rebuilt, Mud Pump Recently Installed, some of the Mechanics have also been Rebuilt. Working Drill. Truck has Dual axles up front and in the Rear. Some Rod & Bits are also Available.

Rotary P-Q - SRS #2826

DESCRIPTION: 1981, Portadrill; Model: TKT; Compressor: None; Mud Pump: 5-1/2" X 8 GD FXX; Engine: PTO; Mounted On: 1981 Kenworth; Truck Engine Make: 6V92; Tools/Options: Portadrill TKT: Recently Sandblasted & Painted. 53' Mast Including a 10 section that can be removed. Set up for Range II Drill Rod and can run 40' Casing. 75,000# Pullback, 8-1/2" Retractable Table that was Rebuilt by DSM (17" opening when retracted), Only Drilled 1,500' Since. New Kelly (30' or 32'), Rotary Table, Hoses and Wash Pipe. No Tooling Included but there is 2,200' of 2-7/8" X 30.5' X 2-7/8" IF Drill Rod & Pipe Boat available for an Extra Cost.

Rotary P-Q - SRS #2802

DESCRIPTION: 1979, Portadrill; Model: 524; Compressor: 256 LeRoi; Mud Pump: 5-1/2" X 8 Gardner Denver; Engine: PTO; Mounted On: 1979 International Paystar 5000; Tools/Options: Portadrill 524: PRICE REDUCED !! 5 Leveling Jacks, 7-1/2" Retractable Rotary Table, 26' Kelly, 3 Line Machine (Sand Line & Kelly), 2" Little Giant Swivel, Racking Board. No Rod Included. Ready to Drill.

Rotary P-Q - SRS #2497

DESCRIPTION: 1978, Portadrill; Model: TKT Prospector; Compressor: LeRoi 256-S2 500/250; Mud Pump: 5-1/2" X 8" Gardner Denver (NEW); Engine: PTO; Mounted On: Kenworth C-500; Truck Engine Make: Detroit Diesel; Tools/Options: Portadrill TKT Prospector: 8" Retractable Rotary Table, 22" Opening, 43' Mast, Rod Box, 25 GPM Bean Water Injection Pump, 3 Hydraulic Jacks, Heavy Duty Drawworks, 70,000 # Pullback, (Larger Pump & Motor than a 10TK). 4-1/2" X 26-1/2" Kelly on rig is worn but will include a NEW 4-1/2" kelly to put on rig. Portadrill Swivel, Rig is Straight Hydrostatic - No Clutches. Truck has 8LL Transmission. Truck Engine & PTO Rebuilt 2013.

Rotary P-Q - SRS #2441

DESCRIPTION: 1976, Portadrill; Model: 10 TKT; Compressor: LeRoi 256S2; Mud Pump: None; Engine: Detroit 8V71; Mounted On: 1998 International 8100; Truck Engine Make: DT 466; Tools/Options: Portadrill 10TKT: Top Hammer Drive, 60,000# Pullback, 60,000# Torque, 45' Mast, Retractable Rotary Table, Bean Water Injection Pump, (4) Hydraulic Leveling Jacks. Includes (16) 352' of 4-1/2" X 22' Drill Rod.

Rotary P-Q - SRS #2206

DESCRIPTION: Portadrill; Model: 10 TK; Mounted On: 1995 Tandem Paystar; Truck Engine Make: CAT 3406; Tools/Options: Portadrill 10 TK: 50,000# Pullback, 2 Hydraulic drawworks Winches. 1 Wireline Core & 1-10,000# Tugger Winch. 4-Motor Ingersoll Rand Top Drive, 25 XV Swivel, All New Hydraulic Pumps & Plumbing in the last 60 days of work. New Spicer Box. Extensive work has just been performed on the drill. Approx. 656' of 4.5" Drill Pipe, (1) 30' X 6-1/4" Drill Collar, (4) 32' X 4.5" Collars included.

Southern Office:
1485 DeSoto Blvd N
Naples FL 34120
Phone: 239.774.1939
FAX: 239.774.6666

Northern Office:
Oil City PA 16301
Phone Toll FREE: 1.888.204.3907
Fax: 814.676.0378