Rotary H-I

Search:
SRS#:
Category:
Keyword:

Rotary H-I - SRS #3541

DESCRIPTION: 1986, Ingersoll Rand; Model: TH-60; Compressor: 750/300; Mud Pump: 4X3; Engine: PTO; Mounted On: 1985 International; Truck Engine Make: Detroit 8V92; Tires: Good; Condition: Operational; Tools/Options: Ingersoll Rand TH-60 Year: 1986: Approx. 8,500 Hours on the Compressor and approx. 80 Hours on the Engine, Recently Replaced. Water Injection Pump, Carousel, Pipe Rack, Gearmatic Winch, (4) Hydraulic Jacks. Updates Include, New Tophead with 4 Motors, New Main Cylinder, Clutch Plate, Diaphragm Gear on Main Compressor Replaced, Mud Pump Rebuilt. Truck has an 8-Speed Transmission and Approx. 86,000 Miles. Includes 180' of 3.5" X 20' Drill Rod and Breakout Wrench.

Rotary H-I - SRS #3530

DESCRIPTION: 1992, Plains; Model: A2000 SIMILAR TO A T2W ; Compressor: 200/300; Mud Pump: 3X5 Mission; Engine: PTO; Mounted On: 1992 GMC Topkick; Truck Engine Make: Jasper < 200 Hrs.; Condition: Ready To Drill; Tools/Options: Plains A2000 Year: 1992: Similar to a Late Model IR T2, Most Parts are Interchangeable. Purchased in 2006, Every Main Component has been Rebuilt or Replaced since then. 30,000# Pullback, No Carousel. Good for 600' Geothermal or Water Wells. 2-Speed Tophead, New Jasper Engine with < 200 Hours on it, Two Winch Lines 8,000# and 12,000#, Ready to Drill. Truck has a 10-Speed Transmission, Odometer Reads 490,000 Reads as it is Drilling. Includes 600' of Near New 3.5" Drill Rod and a 1982 GMC 20' Box Truck that is Set up to Haul Casing and Extra Drill Rod, Welder and Tooling. Has Carried 600' of 3.5" Rod in the Rod Box.

Rotary H-I - SRS #3527

DESCRIPTION: 1983, Ingersoll Rand; Model: TH 55; Compressor: 600/250 Screw Type; Mud Pump: Wheatley 6X6 Duplex 200 GPM; Engine: PTO; Mounted On: 1980 GMC General 6X4; Truck Engine Make: Detroit 8V71; Tools/Options: Ingersoll Rand TH 55 Year: 1983: DHD Lubricator, 18 GPM Bean Water Injection Pump, 200 GPM Mud Pump, 4 Motor Rotary Head, 0-160 RPM Rotation, 2-1/2" Mud & Air Piping, 34' Standard Mast, 16,000# Capacity Main Winch, 2,000# Capacity, High Speed Bailing Winch. Rig is Set Up for 4.5" OD Drill Pipe, No Pipe Included. Has a 3.5" OD Stinger, Slips and Breakout Wrench.

Rotary H-I - SRS #3020

DESCRIPTION: Ingersoll Rand/Cyclone; Model: TH-60 ; Compressor: 750/250; Engine: PTO; Mounted On: 1999 Western Star; Truck Engine Make: Cummins N14; Condition: Parts Rig; Tools/Options: Ingersoll Rand/Cyclone TH-60: RIG WAS ON FIRE. LOTS OF GOOD PARTS AND ROD AVAILABLE. Mast, PTO, Winches, Oil Pumps, Gear Boxes and Other Parts. Had a 750/250 Compressor. Wireline Winch, Capable of a Casing Hammer Rig has the Tails for the Rollers, Lifting Ram & Jib, Rig is set up to run 3.5" X 20' Drill Rod, 9-Pod Carousel (holds 180'). 475-500 HP Engine. Rig is a Late 70's Early 80's that was Completely Rebuilt Prior to the Fire. 900' of Available for an Extra Cost: 3.5" X 20' Drill Pipe that is Near New, Only Drilled 30 Holes.

Rotary H-I - SRS #3481

DESCRIPTION: 1995, Ingersoll Rand; Model: T4W; Compressor: 1050/350; Engine: KTA 19-C; Mounted On: CCC; Truck Engine Make: 300 HP Cummins; Condition: Ready to Work; Tools/Options: Ingersoll Rand T4W (1995): 50K Pullback, Worm Gear Tophead, Rig is set up to run 4.5" X 25' X 3.5" API Reg Drill Pipe, Can Haul 12 Rods Total, Four on the Side, Seven in Carousel and One on the Head. Jib Hoist and Rod Handler, Electric In-line Oiler, 25 GPM Water Injection Pump, Rig has approx. 1,116 Hours, New Rubber. Drill Pipe Available. Original Owner. Carrier has a Jake Brake and approx. 14,491 Miles

Rotary H-I - SRS #3480

DESCRIPTION: 1988, Ingersoll Rand; Model: T4W; Compressor: 900/350; Engine: KTA 19-C; Mounted On: CCC; Truck Engine Make: Cummins; Condition: Ready to Work; Tools/Options: Ingersoll Rand T4W (1988): 40K Pullback, Deck Engine Reconditioned in 2005, 1,836 Hours. Spur Tophead , 25 GPM Water Injection Pump, Electric In-line Oiler, Carousel, Jib Hoist, Rod Handler. New Rubber all Around. Rig is set up to run 4.5" X 25' X 3.5" API Reg drill pipe, pipe available. Rig can Haul a total of 12 rods. Original Owner. Carrier has a Jake Brake and approx. 21,062 Miles.

Rotary H-I - SRS #3472

DESCRIPTION: 2008, Howard Turner; Model: 3KDD 5KDD MUSTANG; Mud Pump: Auxiliary GD FZ-FXZ; Engine: CAT C7 260 HP; Mounted On: 50' Tandem Trailer; Tires: 11R 24.5; Condition: Excellent; Tools/Options: Howard Turner 3KDD 5KDD Mustang (2008): Allison Transmission, Drawworks has PO3-10 Twin Dish Clutches, 8X28 Brakes (2 per drum), 14" Drums, Leabus for 3/4" Cable, 25,000# Single Line Pull, 40,000# Double 120 Chain. 62' X 6' X 3' Mast, 150,000#, Crown has Two 18" Sheaves, Four 15" Sheaves, Six 5" Sheaves, Two 8" Sheaves Winch Line, One Anker Dead Line & Load Cell for 3.4" and 1/2" Cable. 12" Howard Turner Rotary Table, Howard Turner 3" Water Course Swivel, HTB 100 Ton Blocks, Mud Lines, Jib Winch, Water Cooled CAT Engine, Hydraulics: 20 GPM, 2000 psi, PTO Driven from Allison Transmission, 40 Gallon Reservoir. Six Leveling Jacks (37,500# Max.), 40" Stroke, 240 Gallon Fuel Tanks. Optional Equipment: Racking Board, Rig Lights, Catheads, Slips, Tongs, Derrick Climber, Weight Indicator, Hand Rails, Wire Line Units, Welder-Generator, Breakout Cylinder, Snub Lines.

Rotary H-I - SRS #3470

DESCRIPTION: 1994, Ingersoll Rand; Model: TH-75; Compressor: IR 900/350; Engine: Cummins KT-19; Mounted On: Ford L9000; Truck Engine Make: CAT 3406; Condition: Good Working Order; Tools/Options: Ingersoll Rand TH-75 (1994): Truck has 95,000 Miles on it. Includes 300' of 4.5" Drill Pipe. Rig is in Good Condition just needs Paint.

Rotary H-I - SRS #3432

DESCRIPTION: 1995, Ingersoll Rand; Model: TH60; Compressor: HR2 750/300; Mud Pump: MCM 3X4X13 Centrifugal; Engine: PTO; Mounted On: IHC Paystar 5000; Truck Engine Make: Cummins N14 435 HP; Condition: Not Ready to Drill, Price is "as is"; Tools/Options: Ingersoll Rand TH60 (1995): 34' Mast with Telescoping & Swinging Jib Boom, 9-Rod Carousel set up to Handle 3.5" X 20' Drill Pipe, Gearmatic 16,000# Single Line Main Winch, 2,000# High Speed Sand Reel Winch, CAT 25 GPM Water Injection Pump, 4 Hydraulic Leveling Jacks, Feed Cylinder & King Swivel have Low Usage since Replaced. Spicer 792 Air Shift Transfer Case. Recent Work to Date: New Sauer Sunstrand Series 23 Pump, Sauer Sunstrand Series 24 Pump, New Funk Hydraulic Pump Drive Box, New Rod Box, Replaced Engine Main & Rod Bearings, New Operator Platforms, New Swing Table with New Style Hinge (not installed), (3) New ARO Pneumatic Foot Pedals, New Tool Box (not installed), Rebuilt Compressor UL88 Valve. Rig is not ready to drill, price is "as is".. Condition:

Rotary H-I - SRS #3414

DESCRIPTION: 2000, Ingersoll Rand; Model: T4W-DH; Compressor: Ingersoll Rand HR2.5 1250/350 REBUILT 2013; Engine: Cummins QSK19; Mounted On: 6X4 CCC; Truck Engine Year: CAT 3306C; Tires: New; Tools/Options: Ingersoll Rand T4W-DH, (Year 2000): 70,000# Deephole Package, 7-Rod Carousel and a 4-Rod Storage Rack, Jib Hoist & Boom, Compressor Rebuilt in 2013, Spur Gear Rotary Head Rebuilt in 2015 @ 12,500 Hours, All Hydraulic Pumps Rebuilt in 2014, New Injectors in 2012, New ECM in 2014, New Seal Kit on Deck Engine 2014, New Tires All Around, New Funk Gearbox, Hydraulic System Flushed, Rotary Head Packing Oil Changed in 2017, Compressor Oil Changed 3 Hours Ago. $18K Recently Spent on Deck Engine Maintenance. Fuller Transmission, Torque Limit Control, DHD Lubricator, 25 GPM CAT Water Injection Pump. Includes 975' of 4-1/2" X 25' Drill Pipe, Misc. Crossover Subs an (1) 10" X 20' Long Drill Collar.

Rotary H-I - SRS #3412

DESCRIPTION: 2003, Ingersoll Rand; Model: T3; Compressor: 1050/350; Mud Pump: Plumbed; Engine: C15; Mounted On: 2003 Sterling; Truck Engine Make: C12; Condition: Working Drill; Tools/Options: Ingersoll Rand T3 Year: 2003: Rig Currently has Approx. 15,250 Hours, Working Daily. No Mud Pump or Rods Included. 12,000# Winch, Rig Runs 3.5" Drill Rod, 2-3/8" IF. July 2018 New Rotation Pump and Motors Installed, Hydraulic Oil and Filters Changed..

Rotary H-I - SRS #3411

DESCRIPTION: 2000, Ingersoll Rand; Model: T3; Compressor: 900/350; Mud Pump: See Below; Engine: CAT 3406; Mounted On: International; Truck Engine Make: C10; Condition: Working Drill; Tools/Options: Ingersoll Rand T3 Year: 2000: Rig Currently has approx. 14,000 Hours, Working Drill Changes Daily. 18,000# Winch, 4.5" Rods, 2-7/8" IF, Hydraulic Oil Recently Changed, New Tophead Swivel Bearings July 2018. Rig has a Centerline Mud Pump but not Included in Price, would be Removed. No Rod Included.

Rotary H-I - SRS #3397

DESCRIPTION: 1977, Ingersoll Rand; Model: TH-60; Compressor: LeRoi 256S2 450/250; Mud Pump: Gardner Denver 5X6; Engine: PTO; Mounted On: 1997 Western Star; Truck Engine Make: Cummins M-11 350 HP; Condition: Great, Ready to Drill; Tools/Options: Ingersoll Rand TH-60: REMOUNTED AND REBUILT! Mud Pump and Compressor both in Good Condition. 7-Rod Carousel, Rod Box, Standard Mast (32'?), High Speed Bailing Drum with New Line. 4X3X10 Mission Centrifugal Pump runs off PTO on Main Truck Transmission, Rig Throttle is Electric, running off of Electronic Cummins Engine. All hydraulic Cylinders on Rig were Removed and Rebuilt Including Leveling Jacks. All New Hydraulic Hoses and Air Lines. New Tophead Hoisting Cables and Tophead Completely Rebuilt with 4 New Motors. Rebuilt Pipe Tub and New Cooling Radiators on the air Compressor. Gearmatic Winch Rebuilt to New Specs (16,000# Single Line Pull). New 2.5" Water and Air Discharge Hose. Funk box Rebuilt (gears flipped, new bearings and seals). One New Saur Danfoss 90 Series Pump (100cc) Runs Tophead, One Sunstrand still in use (bench tested at 92% efficiency) and Commercial Gear Pump Completely Rebuilt. New Saur Danfoss (75cc) Runs Mission off Main Transmission. Control Panel has Air Controls for most Functions but has Electric over Hydraulic Controls for Tophead Motors and Mission Pump Control. New Belts on Air Compressor and Hydraulic Cooler. Truck has Twin Steer Axles, 9-Speed Transmission, 46,000# Full Locking Rear Differentials, Rebuilt Fuller 2A92 Gear Box with Power Tower that Runs Rig, Truck is in Excellent Condition. Includes approx. 300' of 4" Drill Pipe with Subs and Bits.

Rotary H-I - SRS #3372

DESCRIPTION: 1974, Ingersoll Rand; Model: T4; Compressor: 600-150/250 Rotary Vein Rebuilt 2011/12; Mud Pump: None; Engine: PTO; Mounted On: CCC; Truck Engine Make: Detroit 318; Condition: Truck Caught Fire; Tools/Options: Ingersoll Rand T4 (1974): Truck was on fire but rig runs per owner. Rotary Vein Compressor, that was rebuilt 2011/12. Present Owner Owned it since 1980, Only Drilled 8 Wells. Table plate comes out allowing for about a 22" opening. Includes approx. 150' of 5.5" O.D. X 25' Drill Rod.

Rotary H-I - SRS #3355

DESCRIPTION: 1979, Ingersoll Rand; Model: TH-60; Compressor: 750/250 Screw; Mud Pump: Gardner Denver 5X6; Engine: PTO; Mounted On: 1995 Kenworth T800; Truck Engine Make: Cummins 425 HP N14; Condition: Very Good; Tools/Options: Ingersoll Rand TH-60 : 4-Motor Tophead with 2-7/8" Threads, set up for 4.5" O.D. Pipe. 20K Front End, 40,000# Pullback, Rod Box, 7-Rod Carousel, Bean Water Injection, 2-Stage Air Compressor, Sand Line, Auxiliary PTO for Lift Pump, Two Brand New Batteries. Capable of Handling a Casing Hammer (not included), Ready to Work, Includes 200' of 4.5" O.D. Drill Rod. Can be Sold with a service truck and water truck for an extra cost. Rig has approx. 2,080 Total Hours, put approx. 600 hours on it since rebuild in Feb., 2015. Meter Reads 9,734. Truck is all Original.

Rotary H-I - SRS #3329

DESCRIPTION: 2003, Ingersoll Rand; Model: TH-60; Compressor: 900/350; Mud Pump: 7.5" X 10" Centerline; Engine: PTO; Mounted On: 2003 IHC; Truck Engine Make: C15; Tools/Options: Ingersoll Rand TH-60: Long Tower (38'), approx. 16,922 Hours, approx. 650,000 Miles (mileage runs with the rig in drill mode, not actual truck miles). Set up for a Casing Hammer (casing hammer not included). Rig is Set Up for 4.5" Pipe.

Rotary H-I - SRS #3328

DESCRIPTION: 2003, Ingersoll Rand; Model: TH-60; Compressor: 900/350; Mud Pump: See Below; Engine: PTO; Mounted On: 2003 IHC; Truck Engine Make: CAT C-15; Tools/Options: Ingersoll Rand TH-60: Short Mast (32'), approx. 19,500 Total Hours. Engine Rebuilt approx. 9,000 Hours Ago. Has a Hydraulic Pump for a Mud Pump but Currently does not had a Mud Pump Installed. Rig is Set Up for 4.5" Pipe.

Rotary H-I - SRS #3159

DESCRIPTION: 2002, Ingersoll Rand; Model: RD-20 Range III; Compressor: 1250/350; Mud Pump: See Below; Engine: CAT 3412; Mounted On: 4-Axle CCC; Tools/Options: Ingersoll Rand RD 20 Range III: PRICE REDUCED! Deck Engine has Less than 700 Hours. Includes a 2000 Freightliner with Drop Deck Trailer, 1,800' of Drill Pipe, 6" & 8" Collars. Also Available for an Extra Cost is a Gardner Denver 7-1/4" X 16" Mud Pump on a Lowboy Trailer & 2010 Western Star Truck, both with Detroit 671 Engines. 1996 Volvo with Flat Bed Trailer, 40' X 10' Mud Pit, Shaker & Desanders.

Rotary H-I - SRS #3308

DESCRIPTION: Ingersoll Rand; Model: TH-60; Compressor: LeRoi 600/250 (to be confirmed); Mud Pump: See Below; Engine: PTO; Mounted On: 1976 Paystar 5000; Truck Engine Make: Detroit 8V71; Condition: Fair; Tools/Options: Ingersoll Rand TH60: Has Hydraulics for Mud Pump but Mud Pump not Included. 7-Pod Carousel, Rig is set up to run 4.5" Drill Rod, Main Line & Sand Line. Needs a little TLC, some Hydraulic Leaks. Hours & Miles Unknown, Rig & Truck are both Operational. No Rod or Tooling Available.

Rotary H-I - SRS #3107

DESCRIPTION: Ingersoll Rand; Model: TH-60; Compressor: 750/250; Mud Pump: None; Engine: PTO; Mounted On: 1978 IHC; Truck Engine Make: Cummins; Tires: Front New, Rear OK; Condition: Good; Tools/Options: Ingersoll Rand TH-60 : 38' Mast, 7-Rod Carousel, Rod Box that Holds 8 Rods, Oiler, Foam Injection, 30 GPM Water Pump, 2 Winch Lines. (1) Front Jack, (2) Rear Jacks, Cotta Box gone through in 2008, Carrier Engine Overhauled in 2007, Carrier has approx. 365,000 total Miles, approx. 4,000 Hours on Overhaul. Includes 600' of 3-1/2" Drill Rod and Much More.

Rotary H-I - SRS #2384

DESCRIPTION: 1991, Ingersoll Rand; Model: Hurricane 2000; Compressor: 750/350 HR 2; Mud Pump: Hydraulic Gardner Denver 5X6; Engine: PTO; Mounted On: 1991 Autocar; Truck Engine Make: CAT 3406, 350 HP 14.6L; Tools/Options: Ingersoll Rand Hurricane 2000: 283,742 Miles on Autocar, Two-Speed Head, Approx. 36' Mast, Rod Box, Rawson Koenig 4,000# Sandline Winch, Compressor Disconnect Clutch, Braden OD 12C 12,000# Main Winch (No Winch Swing), CAT 3-Cylinder M1010 12-GPM Injection Pump, No Carousel. Hydraulic Mud Pump. 8LL Transmission, 18,000# Front Axle, 46,000# Rears. Compressor Hrs. Unknown. 2014 Left Rear Jack was Rebuilt, Exhaust was Inspected & Repaired, Pump Drive Input Seal Replaced. DOT Work: Some New Tires, New Shocks, Tie Rod Ends & Tube.

Rotary H-I - SRS #2794

DESCRIPTION: 2004, Ingersoll Rand; Model: T3W; Compressor: 1070/350; Mud Pump: None; Engine: CAT C15; Mounted On: Internaional 7600i; Tools/Options: Ingersoll Rand T3W: One Owner Rig, 5,000 Original Hours. Compressor Disconnect Box, 32,500# Pullback, 18,000# Main Winch, 2,000# Sandline Winch. Set up to run 4-1/2" Rod.

Rotary H-I - SRS #2754

DESCRIPTION: 1986 REFURBISHED IN 2011, Ingersoll Rand; Model: DM-25 RC; Compressor: IR 900/350; Mud Pump: N/A; Engine: PTO; Mounted On: Tracks; Truck Engine Make: 525 HP Detroit; Tools/Options: Ingersoll Rand DM-25 RC: RIG REFURBISHED 2011 @ 300 HRS. 70,000# Pullback, Deck Engine & Compressor have 300 Hours on them since Refurbished. Tophead Rebuilt with New Motors, Angle Capacity to 35 Degrees, 4" RC Hose, Includes 2,000' of 4-1/2" X 20' Matrix RC Pipe, 2,200 Gallon Flat Water Tank Mounted on a 1996 International 6X6 Powered by a 300 HP CAT, Single Stage, 900 CFM/800 psi (Grimmer Schmidt) Hurricane Booster (approx. 1147 Hrs.), Cyclone, Wet Splitter, 5" Hammer. Many Spare and Back Up Parts. Also includes a Back up Compressor. Drill is also available without all of the support equipment.

Rotary H-I - SRS #2749

DESCRIPTION: 2006, Hemsco; Model: Warrior Range III; Compressor: N/A; Mud Pump: Skid Mounted Available; Engine: PTO; Mounted On: 2005 International 5600i 6X8; Truck Engine Make: Cummins ISX565; Tools/Options: Hemsco Warrior Range III: Certified and Ready to Drill. Hemsco 52.5' Mast Rated at 110,000# Static Hook Load, Mast is Complete with 7/8" Cable, Dual Raising Cylinders, 10" Crown Sheaves, Break-Out Wrench and Petol Wrench. Integral Hydraulic System with Common Reservoir, Thermal Exchanger & Infrastructure for Interconnecting Plumbing. Foremost Model 1500 Topdrive Rated at 0-8,000 ft torque, 140 rpm. 192 fpm Fast Feed Down, 106 fpm Fast Feed Up. Pull Master H25 Drawworks Rated at 25,000# with 3/4" Line. Hydraulically Driven Enid Super Bowl Rotary Table with 16" Opening. Integral doghouse with BOP Controls, Knowledge Box, Lockers, etc. Truck is a Tandem Steer Tri-Drive, 18-Speed Manual Transmission. (2) 20,000# Front Axles and (3) 18,000# Rears. 11,145 Hours, 17,975 Miles. Support Equipment Available for an Extra Cost. Consists of Mastco Ramp Style Sub Rated at 120,000#, (5) Compartment Skidded Mud Tank with (4) Guns, Shaker, (2) 40 P Centrifugal Pumps & 7.5 HP Fill Pump, National Pump, Trailer Integrated Catwalk with Skate & (2) Raising Internal Tubs, 2004 Great Dane Dual Wheel Tandem Axle Trailer, Skid Mounted Boiler with Enclosure, Accessory/Generator Utility Building, Emsco D-550 Mud Pump with 60 Series Detroit.

Rotary H-I - SRS #2747

DESCRIPTION: Ingersoll Rand; Model: TH-60 Range III; Compressor: N/A; Mud Pump: Gardner Denver FXX-172 Duplex; Engine: PTO; Mounted On: 1998 International 5000 6X4; Truck Engine Make: Cummins N14; Tools/Options: Ingersoll Rand TH60 Year: PTO; Compressor: N/A; Mud Pump: GD FXX-172; Mounted On: 1998 Int. 5000 6X4; TrEngine: , Cummins N14; Tools/Other Options: 51' Mast Rated at 40,000# Static Hook Load Capacity, Complete with 3/4" Cable, Dual Raising Cylinders, 8" Crown Sheaves, Break-Out Wrench and Petol Wrench. Integral Hydraulic System with Common Reservoir, Thermal Exchanger and Infrastructure for Interconnecting Plumbing. Braden Model CH230 Drawworks Rated at 18,000# Strung with 3/4" Line. Hydraulically Driven Duplex Mud Pump Rated at 52 HP and 330 rpm Maximum on Jackshaft. 8" Stroke and 6" Bore, 4" NPT Suction Connection and 3" NPT Discharge Connection. Atlas Copco Model GD 2000 Topdrive Rated at 0-5,000 ft torque, 12 rpm. 200 fpm Fast Feed Down, 137 fpm Fast Feed Up. King Model 20XV Swivel. Single Steer Tandem Truck Powered by a 460 HP Diesel Engine, 18-Speed Transmission. (1) 20,000# Front Axle and (2) 23,000# Rears. 6,094 Engine Hours, 335,326 Miles.

Rotary H-I - SRS #2746

DESCRIPTION: 1980, Ingersoll Rand; Model: TH-60 Range III; Compressor: IR 600/250; Mud Pump: GD FXX 172 Duplex; Engine: PTO; Mounted On: 2005 Mack CV713; Truck Engine Make: 350 Diesel; Tools/Options: Ingersoll Rand TH 60 Range III: OFF MARKET. 51' Mast Rated at 40,000# Static Hook Load, Complete with 3/4" Cable, Dual Raising Cylinders, 8" Crown Sheaves, Break-Out Wrench & Petol Wrench. Integral Hydraulic System with Common Reservoir, Thermal Exchanger & Infrastructure for Interconnecting Plumbing. Braden CH230 Drawworks rated at 18,000# with 3/4" Cable. Hydraulically Driven Duplex Mud Pump Rated at 52 HP and 330 rpm Maximum on Jackshaft. 8" Stroke, 6" Bore, 4" NPT Suction Connection and 3" NPT Discharge Connection. Atlas Copco GD 2000 Topdrive Rated at 0-5000 ft. torque, 125 rpm. 200 fpm Fast Feed Down, 137 fpm Fast Feed Up. King Model 20XV Swivel. Truck is Single Steer, Tri-Drive Powered by a 500 HP Engine, 18-Speed Manual Transmission. (1) 20,000# Front Axle and (3) 17,000# Rears. 9,056 Engine Hours and 471,404 Miles. OFF MARKET

Rotary H-I - SRS #2744

DESCRIPTION: 1980, Ingersoll Rand; Model: TH-60 Range III; Compressor: N/A; Mud Pump: GD FXX 172 Duplex; Engine: PTO; Mounted On: 2003 International 5600i 6X8; Truck Engine Make: CAT C15; Tools/Options: Ingersoll Rand TH 60 Range III: 52' Mast Rated at 30,000# Static Hook Load Capacity Complete with 3/4" Cable, Dual Raising Cylinders, 8" Crown Sheaves, Atlas Copco GD 2000 Topdrive Rated at 0-5,000 ft torque, 125 rpm. 200 fpm Fast Feed Down, 137 fpm Fast Feed Up, King 20XV Swivel, Break-Out Wrench & Petol Wrench. Integral Hydraulic System, Common Reservoir, Thermal Exchanger and Infrastructure for Interconnecting Plumbing. Braden CH230 Drawworks Rated at 18,000# with 3/4" Line. Hydraulic Duplex Mud Pump Rated at 52 HP and 330 RPM Maximum on Jackshaft. 8" Stroke, 6" Bore, 4" NPT Suction Connection and 3" NPT Discharge Connection. Truck is Single Steer and Tri-Drive Powered by a 475 HP Engine with an Eaton 18-Speed Manual Transmission. (1) 20,000# Front Axle and (3) 17,000# Rears. 14,646 Hours and approx. 18,725 Miles.

Rotary H-I - SRS #2742

DESCRIPTION: 1980, Ingersoll Rand; Model: TH-60 Range III; Compressor: N/A; Mud Pump: GD FXX 172 Duplex; Engine: PTO; Mounted On: 1999 Peterbuilt 357; Truck Engine Make: CAT 3406; Tools/Options: Ingersoll Rand TH-60 Range III: Refurbished Rig. Ingersoll Rand Model Mast, 51' and Rated at 40,000# Static Hook Load Capacity. Mast is Complete with 3/4" Cable, Dual Raising Cylinders, 8" Crown Sheaves, Break-Out Wrench and Petol. Integral Hydraulic System including Pumps, Common Reservoir, Thermal Exchanger and Infrastructure for Interconnecting Plumbing. Atlas Copco Model GD 2000 Topdrive Rated at 0-5,000 ft Torque, 125 rpm, Fast Feed Down 200 fpm, Fast Feed Up 137 fpm. King Model 20XV Swivel. Hydraulically Powered Duplex Mud Pump Rated at 52 HP and 330 rpm Maximum on Jackshaft. 8" X 6" Bore, 4" NPT Suction Connection and 3" NPT Discharge Connection. Truck is Tandem Steer, Tandem Drive. Eaton 18-Speed Manual Transmission. (2) 18,000# Front Axles, (2) 23,000# Rears. 577,355 Miles, 7,648 Hours. Support Equipment Available for Purchase.

Rotary H-I - SRS #2740

DESCRIPTION: Ingersoll Rand; Model: T3W Range III; Compressor: 1070 HR 2.5; Mud Pump: (2) GD FXX-172 Duplex; Engine: PTO; Mounted On: 2004 International 5600i 6X8; Truck Engine Make: Cummins ISX475; Tools/Options: Ingersoll Rand T3W Range III: 45' Mast Rated at 45,000# Static Hook Load Capacity. 28,500# Pullback, 30,000# Pulldown. Mast is complete 3/4" Cable, Dual Raising Cylinders, 6" Crown Sheaves, Break-Out Wrench & Petol. Integral Hydraulic System Including (4) Pumps and Common Reservoir, Thermal Exchanger and Infrastructure for Interconnecting Plumbing. Atlas Copco Topdrive rated at 0-5,000 ft. Torque, 125 rpm, Fast Feed Down 200 fpm, Fast Feed Up 137 fpm. Braden Model CH230 Drawworks Rated at 18,000# Strung with 3/4" Line. King Model CM25 Swivel. Each Hydraulically Driven Duplex Mud Pump is Rated at 52 HP Maximum BHP and 330 rpm Maximum on Jackshaft. Pumps have an 8" Stroke and 6" Bore (4" NPT Suction Connection X 3" NPT Discharge Connection). Single Steer Truck, Eaton 18-Speed Manual Transmission. 20,000# Front Axle, 54,000# Rears. Truck has approx. 683,828 Miles on it.

Rotary H-I - SRS #2729

DESCRIPTION: 2008, HTB; Model: 2500; Compressor: N/A; Mud Pump: N/A; Engine: 180 HP 6-Cylinder Diesel; Mounted On: Trailer; Truck Engine Make: N/A; Tools/Options: HTB 2,500' Drill: Double Drum Drawworks, 18,000# Single Line Pull, 12" Howard Turner Retractable Rotary Table, 55' Free Standing 150,000# Derrick, 40-Ton 3" Swivel, 4.5" Kelly. 2 4-Part Traveling Blocks - 50 Ton. Drive Bushing, Hydraulic Port for Power Tongs, Make-Up & Break-Out Cylinders with Jerk Lines and Snub Lines. Weight Indicator, Ladder & Derrick Climber. Wireline Unit on Board. Emergency Shut Down Kill Switch, (4) Hydraulic Leveling Rams, Steps and Hand Rails.

Rotary H-I - SRS #2512

DESCRIPTION: 2000, Ingersoll Rand; Model: ECM 690; Compressor: 420/150; Mud Pump: None; Engine: CAT 3306; Mounted On: Tracks; Condition: Good Running Drill; Tools/Options: Ingersoll Rand ECM 690: Dust Collector, Water Injection, Air Conditioned Cab, YH 135 Drifter Hammer, Runs T 51 Drill Rod, Rig is rated @ 70' - 3.5" - 6" Holes. Approx. 8,000 + Frame/Engine Hours. Good Running Drill. Horizontal Capabilities. Included or can be purchased separate: 1999 IR ECM 690 Parts Rig with a CAT Engine & Air Compressor.

Rotary H-I - SRS #2400

DESCRIPTION: 1979, IDECO ; Model: BIR 7515 800 HP; Compressor: Sullair 125/100; Mud Pump: (2) GD PZ-7; Engine: (2) CAT 3406-C; Mounted On: 6-Axle 60 Ton Carrier; Truck Engine Make: CAT; Tools/Options: Ideco BIR 7515 800 HP: 2-Motor 10-Line Drawworks Rated @ 750 HP, powered by 2 CAT 3406-C Diesel Engines & Allison Transmission. 50,000# Main Drum with 1-1/8" LeBus Grooved Sleeve - water cooled. National Swivel, 5-1/4" X 40' Kelly, Foster Spinner, 23" Ideco Table, Martin Decker Weight Indicator, Parmac Hydromatic Auxiliary Brake, 1-1/8" National Deadline Anchor, Koomey Crown Saver, 117' Ideco Kwik-Lift, Telescoping Derrick Rated @ 358,00# w/ 10-Lines, Mechanical, (6) Crown Sheaves, Internally Guyed, Hydraulic Make-up Cathead Rated @ 30,000 ft. lb., Single Line Pull Torque, Hydraulic Break-out Cathead Rated @ 40,000 ft. lb. Single Line Pull, Ideco Sub-Structure. Traveling Block hold 3,500' of 1-1/8" Drill Line, (2) Braden Winches - 12,000# & 10,000# Plus a Man-Rider Winch. Includes: Well Control Equipment, Blow Out Preventers, Casing Stabbing Board, Mud Tanks, Shale Shakers, Desander, Desilter, Mixer, Degasser, All Pipie & Handling Equipment including 9,500' (300 Jts.) 4-1/2" X 32' Range II Drill Rod, Mud Pumps are equipped with Pulsation Dampeners, Pressure Relief Valves, Hoses, Riser, Flowline & H2O Tanks and are Powered by a CAT 550 HP. Rig isequipped with Rig Lighting, External Communication System, Lincoln Welder, Matting, Survey Equipment, Doghouses, Catwalk, Pipe Boats, Complete with all Instrumentation including ADMS System. Rig is Rated @ 3,000 Meters (9,840') with 4-1/2" Drill Rod.

Rotary H-I - SRS #2345

DESCRIPTION: 1989, Ingersoll Rand; Model: RD 10; Compressor: 1170/350; Mud Pump: None; Tools/Options: Ingersoll Rand RD 10: 3000' of Steel, Steel Trailers.

Rotary H-I - SRS #2257

DESCRIPTION: 1978, Ingersoll Rand; Model: T4 Blast Hole; Compressor: 750/150; Mud Pump: None; Engine: Detroit 871; Mounted On: CCC; Truck Engine Make: CAT 3208; Tools/Options: Ingersoll Rand T4 Blast Hole: Spur Head Motor. Hrs. ?? Includes 300' of Drill Rod, 6" Hammer, Rod Sling, Table Bushings.

Rotary H-I - SRS #2167

DESCRIPTION: Ingersoll Rand; Model: Cluster Drill; Tools/Options: Ingersoll Rand Cluster Drill Year: New Rock Hog 380 Hammers, (3) IR 380 Hammers, 85%-90% New. (4) 10" Outer Hammer Bits with 820' of drill footage, (2) Inner Hammer Bits with 420' of Total Footage, 3-1/2" API Pin at Top and 7-5/8" API box at Bottom. Currently drilling 50-51" ventilation Shaft holes to 460' depth in hard rock. Currently running on an IR T 4.

Rotary H-I - SRS #2172

DESCRIPTION: 1988, Ingersoll Rand; Model: ECLM 450-D; Compressor: Not Included; Mud Pump: None; Engine: Detroit 3-Cyl.; Mounted On: Tracks; Tools/Options: Ingersoll Rand ECLM 450-D: Angle drill capabilities, tophead drive, Rod rack,Hydraulically driven. Set up for 6" Air hammer. Includes 90' of 4" Drill rod and (1) Starter rod and slips for 4" drill rod, Break-out Cylinder. Uses auxilliary air, had been running with a 750/250 IR compressor. New radiator still in crate is included the sale. Also has a new exhaust, and 2 planetary gears.

Rotary H-I - SRS #2160

DESCRIPTION: 1992, Hausherr; Model: 80R D.R.S.; Compressor: Atlas Copco 700/290; Engine: CAT 3406; Mounted On: Tracks; Tools/Options: Hausherr 80R D.R.S.: Blast hole drill. (7) 13' X 4" Rods on mast, some extra may be available.

Rotary H-I - SRS #2130

DESCRIPTION: 1998, Ingersoll Rand; Model: CM 695D; Compressor: IR 600/250; Mud Pump: None; Engine: CAT 3306; Mounted On: Tracks; Tools/Options: Ingersoll Rand CM 695D: Dry Dust System, Rod Loader holds (6) 3-1/2" X 15' Drill Rods, 90' which is included.. Condition: Excellent

Southern Office:
1485 DeSoto Blvd N
Naples FL 34120
Phone: 239.774.1939
FAX: 239.774.6666

Northern Office:
Oil City PA 16301
Phone Toll FREE: 1.888.204.3907
Fax: 814.676.0378