Rotary E-F - SRS #3334
DESCRIPTION: Failing; Model: Jed A RC; Compressor: 260 IR - See Below; Mud Pump: None; Engine: Cummins Diesel (Hospital Enclosure); Mounted On: Trailer; Condition: Good; Tools/Options: Failing Jed A RC: Rig is set up for Reverse Circulation, Internal Air on Swivel. Needs Paint but is in good Operating Condition. Engine is in a Hospital Enclosure and runs Quiet. 18" Table, 8,000# 6-Part Main Winch Line, 8,000# 5-Part Hoisting Line, and also has a Sand Line with 1,000' of Cable, 50', 90,000# Mast. 10' 6" Kelly, Four Hydraulic Jacks. Table Rebuilt in 2018. Includes a Tag Along Sullair Compressor Motor approx. 1 Year Old, 40' Trailer with approx. 500' + of 6" Drill Rod, Tooling to set up and Drill, 20' Dog House on Trailer with Small Hand Tools to run Job, 2 Year old Miller Welder.
Rotary E-F - SRS #3244
DESCRIPTION: 1986, Failing; Model: 1750 Holemaster Reverse Circulation; Compressor: LeRoi 253S2B; Mud Pump: (2) Mission Magnum 3X4X13 Reciprocating; Engine: PTO; Mounted On: 1997 Mack; Truck Engine Make: Mack CL713 427 HP Reconditioned; Condition: Complete Setup and Ready for Work; Tools/Options: Failing 1750 Holemaster RC: PRICE REDUCED, OPEN TO OFFERS! Tools/Other Options: Rig is set up for either Flooded Reverse Circulation or Conventional Mud Rotary Drilling, 6" ID through Swivel and Tophead Drive, Table Opening is approx. 8-3/4" the table inserts also come out to set casing and the table opens 8+ inches as well as opening up to set tooling . Tophead Drive has 2,400 Ft.-Lbs Torque @ 1-120 RPM, Tilts Horizontal for Making Connections off a Trailer. Derrick is Rated for 100,000# Static Hook Load Capacity, 55,000# Total Pulling Capacity with a 4-Speed Drive (up to 309 Ft./Min.), Pulldown Chains, Single Drum Drawworks with 15,000# (60,000# on 4-Part Line, 22-Ton Traveling Block). 36' Derrick that Handles up to 25' Casing, Cathead, Mast Mounted Safety Line. Truck has approx. 569,284 Miles on it. Diesel Engine is a 427 HP and has been Reconditioned (low hours since), has an Engine Brake. Reconditioned 8-Speed Eaton Transmission with Deep Reduction Selector. Also Includes a Custom Pipe Trailer (designed by GEFCO) with Slide, Battery or Truck Powered Crane, 590' of 6-5/8" O.D. X 20' Hacker Thread Drill Pipe, 200' of 2" Tremmie Pipe, 1-1/4" Schedule 40 Pic Airline & Couplers, Extra Fittings, Tool chest, 6" I.D. Dual Helix Discharge Hose, 2" Air Hose, 4" Suction Hose with Screen, 20' 6" X .25 Flow Pipe, Elbows, I-Beams. Tooling Includes: Breakout Tongs, Slides, J-Hook, Semco 14" & 16" Heavy Duty Elevators, 20' 10K Drill Collar, 32" Drag Bit, 28" Moab Tricone Roller Bit, 19" TCI Bit, 15" Roller Bit, Swab, Lifting Bail. Also Available for an Extra Cost is a Sullair 375H Air Compressor Powered by a John Deere Engine, approx. 5,554 Hours. Complete Setup, Ready for Work.
Rotary E-F - SRS #3518
DESCRIPTION: Failing; Model: 1250; Compressor: 250 CFM @ 250 psi; Mud Pump: 5X6 Failing; Engine: PTO; Mounted On: 1982 IHC; Truck Engine Make: 466 210 HP; Tools/Options: Failing 1250: 5" Retractable Table with Split Bushings, Pulldown, Rear Outriggers, Bailing Drum, E-log Instrument, Includes 17 Joints of 20' Drill Rod and Tools with Subs up to 8-3/4".
Rotary E-F - SRS #3513
DESCRIPTION: Failing; Model: CFD1; Compressor: GD Developmental; Mud Pump: 3X4X13 Centrifugal; Engine: PTO; Mounted On: 1982 Chevrolet Kodiak; Truck Engine Make: CAT 3208; Condition: Overall Good; Tools/Options: Failing CFD1: Centrifugal Mud Pump with Brand New Fluid end, New Impeller, Housing, Packing, Bearings, Seals. Also Includes a Spare Compressor (unmounted). Rebuilt Rotary Table (new bearings), Rebuilt Swivel, New Bearings, Crossover Sub, Seals and Packing. Includes 300' of 15' Drill Rod. Overall Good Condition but has some Oil Leaks.
Rotary E-F - SRS #3075
DESCRIPTION: Emsco; Model: 200; Compressor: N/A; Mud Pump: See Below; Engine: 500 HP CAT 3406; Mounted On: 3-Axle Trailer; Tires: All New; Condition: Excellent; Tools/Options: Emsco 200: Smooth Operating, Straight, Solid Rig, Gone Through Rig, Deck Engine, Drawworks, Rotary Table, Crown Sheaves, al Cables. Rebuilt Main Derrick Lift Cylinders, Sandblasted and Replaced all Rusted Out/Deteriorated Steel on Rig, Sub Structure and Monkey Board, Rebuilt Hydraulic Breakout Cylinder, Replaced Air Control Valves, Installed and Automatic Driller. Skid Mounted GD PZ7 Mud Pump Operated by a 396 CAT Engine. 200,000# Hook Load, 68' Mast. Approx. 1,000' of New 1" Cable on Front - Parted 6 Times, Single Drum 3-speed Drawworks, Air Clutches, Weight Indicator, 38' Square Kelly 4-1/2" X-Hole, 3" Brewster Water Course Swivel, 18" Brewster Rotary Table, Emsco Drawworks, Hydraulic Break-out Tongs, Chain Spinners, Cat Heads, Monkey Board has been Rebuilt, Hydromatic (not hooked up), 7' Tall Rebuilt Sub Structure 10' Wide, all Support Beams Replaced, Sandblasted and Painted. 6 Hydraulic Leveling Jacks. Mud Pump is Powered by a 471 Detroit Engine. Includes approx. 2,000' of 4-1/2" X-Hole Drill Rod, Random 30' Lengths, approx. (6) 6" Heavy Weight Collar, Rod Slips. Doghouse, 2,200 Gallon Stainless Steel Fuel Tank and Auxiliary Air all Mounted on one 52' Dropdeck Trailer. Pipe Racks, (2) Skid Mounted, Generator Operated Light Plants (one big, one small). Rig is Tooled Up and Ready to Drill. 1,000 Gallon Rig Fuel Tank.
Rotary E-F - SRS #3363
DESCRIPTION: Failing; Model: 1000; Compressor: LeRoi 256; Mud Pump: Gardner Denver 5X6 Piston; Engine: PTO; Mounted On: 1974 Mack; Truck Engine Make: V8; Tools/Options: Failing 1000 : Truck has Low Miles. Drill Sat for 30 Years in a shop. New 2" Little Giant Swivel, 23' Kelly, 5-1/4" Non Retractable Table, Two Hydraulic Jacks, Rod Box, Driller & Operator's Platforms.
Rotary E-F - SRS #3268
DESCRIPTION: 1981, Failing; Model: JED-B Reverse Circulation; Compressor: None; Mud Pump: See Below; Engine: Detroit 471 & 671; Mounted On: Low Frame Tandem Axle Trailer; Tools/Options: Failing JED-B RC: Optional Heavy Duty 58', 90,000# Capacity Derrick with 56'3" Clearance. Drill String Weight Indicator, Double Drum Stacked Drawworks, Twin Disc E-216 16" Type Clutches, 15,000# Single Line Pull, 18-1/2" X 4-1/2" Double Band Type Brakes, Cathead, Failing 18" Hinged 75-Ton Capacity Oil Bath Rotary Table, Round, 9" O.D. X 8" I.D. X 14' Long Kelly Bar, Failing 9" Water Course Oil Bath Swivel. Deck Engine has a 5-Speed Transmission, 6-Part Line on Kelly Drum, 4-Part Line on Tripping Drum, Self Priming Failing Jet Eductor System with 6" X 8" 2,600 GPM High Pressure Centrifugal Pump used t Draw Flow via a Vacuum for Reverse Drilling to Depths of 400' - 600'. When used in conjunction with Air Lift, Depth Capability of 1,000'. By Simply Closing an Air Valve on the system Enables Direct Conventional Mud Drilling to Depths of 1,000'. DT 671 has the Over Center Clutch. Three Hydraulic Outriggers with Two Screw Type Jacks on Table. No Rod or tooling Available.
Rotary E-F - SRS #3032
DESCRIPTION: Inside Electric Rigs; Engine: 3-Phase Electric; Mounted On: Casters - Hitch on Top; Tools/Options: (2) Inside Tophead Rigs, Good for Elevator Shaft Work. Electric Gearbox Driven Rotary Rigs, Air Swivel. Rigs Run 2-7/8" Drill Rod. 5', 10', 13', 20' Rod, Rigs have Winches - Needs a Guide System. Augers and Core Buckets available for an Extra Cost.. Condition:
Rotary E-F - SRS #3008
DESCRIPTION: 1978, Ewbanks; Model: M50; Compressor: See Below; Mud Pump: None; Engine: PTO; Mounted On: 1996 International 4900; Truck Engine Make: DT 466; Condition: Good; Tools/Options: Ewbanks M50 : Solid Rig, New Drawworks Cable Cylinder, New Hydraulic Lines on Drawworks Last Year, New Winch and Turn Table Clutches, New Winch Cable on both Spools, 5,000# on Single Line and 15,000# Double Line, 45,000# Hookload on Derrick. Has Holdback and Pulldown, 3-Cylinder Bean Water Injection with Heavy Duty 9" Retractable Table, 23' Fluted Kelly Bar with 2-7/8" Pin (Very little wear on Kelly Block). Rig has M-75 Drums, 32' Mast, Mechanical Clutches on Drums. Pulldown for Kelly was Reworked, Clutches on Drums Rebuilt. Truck is in Good Condition and has approx. 230,000 Miles on it. Includes a Wilson Breakout Wrench, (2) Quincy Auxiliary Air Compressors, one has a Rebuilt 4-Cylinder Engine (12V71) 1200/150 Air the other is an 850/175 Quincy with approx. 200 Hours on Engine Rebuild (8V92), Compressor Overhauled, both are Skid Mounted and on Trucks. Also Includes approx. 700' of 4" X 20' Drill Rod with 2-7/8" IF Tool Joints, (2) 12" Hammers (1) with a 15-1/2" Bit and (1) with a 17-1/2" Bit. (2) 6" Hammers (1) with a 6-1/2" Bit and (1) with a 6" Bit, all subbed up for 2-7/8", (1) 7-7/8" Tricone Bit (no Sub) and some Misc. Augers. Rig can set Large Diameter Casing.
Rotary E-F - SRS #2970
DESCRIPTION: Failing PARTS RIG; Model: 1500; Compressor: None; Mud Pump: 4 X 5-1/2"; Mounted On: Older Ford F-700; Tools/Options: Failing 1500 PARTS RIG: Mechanical Clutches, 2-Drum (Drawworks & Kelly), Standard Mast (does not fold over), 2-3/8" Kelly. Truck Ran when Parked.
Rotary E-F - SRS #2866
DESCRIPTION: Failing ; Model: 1500; Compressor: N/A; Mud Pump: GD 5X6; Engine: PTO; Mounted On: 1959 Chevy Viking; Truck Engine Make: Straight 6; Tools/Options: Failing 1500: 42' Mast, 2-3/8" Fluted Kelly - Automatic Chuck Pulldown, Break-Out Tongs, Break-Out Table. Runs 2-3/8" Drill Rod. Includes a Portable Mud Pit, Assorted Bits, Stabilizers, 4" & 6" Bail. A Desander is also available. Truck Runs & Drives. Rear Wheel Cylinders Replaced in 2014 along with the Master Cylinder and a Full system Flush. One Owner Rig.
Rotary E-F - SRS #2831
DESCRIPTION: Failing ; Model: CF-15; Compressor: Davey Air Cooled Developmental; Mud Pump: Two on Deck; Engine: PTO; Mounted On: 1973 Ford Tandem Axle with 3rd Tag Axle; Truck Engine Make: Detroit 8V71; Tools/Options: Failing CF-15: 5X6-1/4" Failing & Triplex Mud Pumps on Deck. 27' Mast, 5-1/2" Retractable Table, Hydraulic Chain Pulldowns, 2-7/8" X 23' Fluted Kelly, 2" Swivel, Side Pipe Rack with Fast Slide, (4) Hydraulic Leveling Jacks, Breakout Tongs, Myers Water Injection, Mechanical Clutches on Drawworks. Truck is a Tandem with 3rd Tag Axle. Truck Odometer Reads 21,572 Miles. Rig Recently Painted. Mast is Twisted and will not raise. Truck is Drivable and Engine Runs Good. Mud Pump & Air Compressor need some Work to be Operable. Being sold "As-Is".
Rotary E-F - SRS #2811
DESCRIPTION: Failing; Model: CFD 2 Holemaster; Compressor: None; Mud Pump: 4-1/2" X 5 WABCO; Engine: PTO; Mounted On: 1973 Ford F-350; Truck Engine Make: Gas 390; Tools/Options: Failing CFD 2 Holemaster: Lightweight and Portable, Hydraulic chain Feed Pulldown, Mast is 18' above Table. Also has a 3X4 Centrifugal Auxiliary Mud Pump Powered by a 4-cyl. Motor. Break-Out Wrench, Stationary 5-1/2" Table, 2-7/8" X 10' (?) Fluted Kelly, Bailing Drum has 200' of New Non-Rotating Cable, also has New Non-Rotation Cable on both Drawworks, Hydraulic Front Jack, Rod Box. IF Thread has been changed from Failing Thread. Double Throw, PTO has Low & High, wouldn't engage last time he ran it (2014). Been Sitting for a While. Includes (14) 2-7/8" X 10' Drill Rods, Some Rock Bits & Wing Bits, Subs, 3" & 4" Bailers, Mud Tub, Etc. Truck has a 4-Speed Transmission.
Rotary E-F - SRS #1880
DESCRIPTION: Failing; Model: 1500; Mud Pump: 5-1/2 X 8 GD; Mounted On: 1972 Brockway Truck 351; Truck Engine Make: Detroit 8V71; Condition: Excellent; Tools/Options: Rebuilt rotary table, rebuilt piston mud pump, all new hosing, piping & plumbing with a 4-1/4" X 23' Kelly bar. Table capable of handling 15" casing. 2" swivel, 48' mast. Set up to run 2-7/8" FEDP rod. 300' of brand new, never seen dirt 2-7/8" X 20' FEDP rod available for an extra cost. Rig has been through the shop.
Rotary E-F - SRS #1626
DESCRIPTION: 1978, Failing; Model: CF-15; Compressor: Leroi 50S2 120x60; Mud Pump: 5X6 Failing; Engine: CAT Diesel; Mounted On: gmc brig; Truck Engine Year: 1979; Truck Engine Make: 3208; Condition: Good Running Mach.; Tools/Options: 8" Rotary Table. 3208-210 HP, Kelly 3-3/8" X 23'6". Includes Subs and Stabilizer.
Southern Office: 1485 DeSoto Blvd N Naples FL 34120 Phone: 239.774.1939 FAX: 239.774.6666
Northern Office: Oil City PA 16301 Phone Toll FREE: 1.888.204.3907 Fax: 814.676.0378