Rotary D

Search:
SRS#:
Category:
Keyword:

Rotary D - SRS #3450

DESCRIPTION: 1996 , Drilltech; Model: D25K; Compressor: 900/350; Mud Pump: None; Engine: CAT 3406; Mounted On: Ford; Truck Engine Make: 8.3 L Cummins; Condition: SOLD; Tools/Options: Drilltech D25K (1996): 18 GPM Pump, Swinging Jib, Has a Sand Line but it is not Plumbed in, Front & Rear Jacks. Includes 360' of 4.5", 3.5" Regular Thread Drill Pipe. Rig & Truck in Good Condition. Owner Believes the CAT & Compressor has approx. 2,000 Hours on it. Holds 300' in the Rod Box and another 120' in the Carousel. SOLD

Rotary D - SRS #3335

DESCRIPTION: 2003, Drilltech; Model: Marlin 6; Compressor: None; Mud Pump: Mission Magnum 4X3X13; Engine: PTO; Mounted On: 2003 IHC 2 Wheel Drive 5800 Series; Truck Engine Make: IHC 344 HP; Condition: Like New, Low Hours; Tools/Options: Drilltech Marlin 6: Low Hours, Like New. 40,000# Pullback, 20,000# Single Part Hoisting Line, 5,000# Sand Line (1,000' of Cable), Two Jibs (hoisting & Sand Line), Four Hydraulic Jacks, 200 GPM@ 250 psi Moyno Pump, Hydraulic Breakout. Includes 500' of 3.5" IF X 20' Flush Drill Rod. Been down 800', 36" Hole set 20" Casing.

Rotary D - SRS #3131

DESCRIPTION: DSI; Model: Quickdrill; Compressor: Unmounted; Mud Pump: Gardner Denver 4X5; Engine: Cummins 4BT; Mounted On: 1982 C-60 Chevy; Truck Engine Make: Detroit; Condition: RIG HAS BEEN SOLD; Tools/Options: DSI Quickdrill : Tophead Drill, Single Axle Truck, Complete Rebuild on Mud Pump, Never Drilled Since. Rig & Truck Runs and Operates but Owner Never Drilled with it. Hour Meter Reads 1,355 and Odometer Reads 23,754. Includes some (approx. 200' +/-) 2-3/8" Drill Rod and Subs to Fit the 3-1/2" Setup on the Rig. Would need Slip to run the 2-3/8" Rod. The Sullair 375DP Compressor is Mounted on a Wagon/Trailer, it Runs but has an Unloader Problem. Would Include a Grout King Grouter (never had any material run through it) with Hydraulically Driven Homemade Hose Reel, 250' of Sewer Jetting Hose (never used) for an Extra Cost. RIG HAS BEEN SOLD

Rotary D - SRS #3531

DESCRIPTION: 1996, Tamrock - Drilltech; Model: D25KW; Compressor: 900/350 Sullair; Engine: CAT 3406B DITA 445 HP; Mounted On: 1996 Ford LTS 9000; Truck Engine Make: 300 HP Diesel; Condition: Working Condition; Tools/Options: Tamrock - Drilltech D25KW Year: 1996: Holte 140 Casing Hammer, 445 HP Deck Engine with approx. 2,860 Hours on a Frame-out Rebuild. 30,000# Pullback and 20,500# Pulldown, Dual Air Intake system, 89 RPM High Torque Head 0 72,000in lbs Torque, Heavy Duty 1-3/4" Feed chain Group, Remote Helpers Station for Independent Control of Winch, Jib Swing & Extension, Compressor Airline Blowdown, 6 Rod Carousel, 20 GPM Water Injection Pump, Foam Injection, electric Airline Lubricator with a 10 Gallon Reservoir, Swinging Jib Boom, Night Lights, Rod Box that Holds 15 Rods, Stabilizer Trough and Hammer Holder, 4 Leveling Jacks, (2) 48" Front, (2) 36" Rear. Approx. 13,000 Rig Hours, Truck has approx. 41,379 Miles on it, 10-Speed Transmission, 18,000# Front and 46,000# Rear Axles. Includes 420' of 4.5" O.D. Drill Rod and the Hand Tools that come Stock on a Rig. Used as a Backup Rig, Drills Once Every Week or Two.

Rotary D - SRS #3378

DESCRIPTION: Drillmax; Model: 250; Compressor: Champion 92/175; Mud Pump: Gardner Denver FXF 4-1/2" X 5"; Engine: PTO; Mounted On: 2005 Ford F550 4X4; Truck Engine Make: 6.0 L Diesel; Tools/Options: Drillmax 250: Rig has approx. 7,002 Hours on it., Braden 6,000# Main Winch, 22' Stroke, 34' Mast, Rig is Set Up to Run 15' Rod, 12,000# Pullback, 10,000# Pulldown, 4 Leveling Jacks, 2 Tool Boxes. Included: Mud Pan and Hoses, Desander and Hoses, 200' of 2-3/8" OD Pipe, (1) 4" Brand New Rerun Bit, (1) 6" and (1) 8" Tricone Bits that only have a few hours on them, Hydraulic Breakout Wrench. 2019 Hydraulic Pump Rebuilt, Several Cylinders were Repacked. Truck has approx. 24,584 Miles. Truck has approx. 24,584 Miles..

Rotary D - SRS #2873

DESCRIPTION: 2012, Duramast; Model: XL100; Compressor: None; Mud Pump: NEW 2X3; Engine: Perkins Diesel; Mounted On: 1999 Ford F-450 2WD; Truck Engine Make: V10 Gas; Condition: Like New; Tools/Options: Duramast XL100: Rig is Like New, has < 20 Hrs. on it. Everything on Deck is New Except for Perkins Engine which has approx. 1,200 Hours on it. Tophead Rig, Runs 10' Drill Rod, Includes a Mast Extension to Set 20' Casing, Break-out Wrench, Bowl & Slips. Truck Odometer Reads approx. 170,000 Miles but Engine was Replaced and has < 80,000 Miles on it. Includes 200' of 2-3/8" X 10' Mayhew Jr. Drill Rod. PRICE REDUCED

Rotary D - SRS #3347

DESCRIPTION: 2005, Deep Rock; Model: DR 150; Compressor: N/A; Mud Pump: 4-1/2" X 5"; Engine: PTO; Mounted On: 2005 Ford F750 2-Wheel Drive; Truck Engine Make: Cummins; Condition: Good; Tools/Options: Deep Rock DR 150: Only 1,453 Hours, 20' Mast, Pullback is approx. 18,000# - 20,000#. Owner has been down 500' with it but can go deeper depending on the rod. Hydraulically Driven Mud Pump, Hammer Oiler, Auxiliary Hydraulics, 12 GPM Water Injection Pump, Hydraulic Rod box, 6,000# Winch, Three Hydraulic Leveling Jacks, Driller & Operators Platforms, Tool Box. Ready to Work, Includes 200' of AWJ Drill Rod. More Rod Available for an Extra Cost. Odometer Reads 7,698.

Rotary D - SRS #3473

DESCRIPTION: 1977, Drilltech; Model: D40K; Compressor: Sullair 750/250; Engine: CAT 3406; Mounted On: 6X4 CCC; Truck Engine Make: CAT 3208; Tools/Options: Drilltech D40K (1977): Tophead Drive with 40,000# Pullback Capacity, Dual Carousels that are Capable of Holding 250' of 4.5" X 25' Drill Pipe, Two Hydraulic Winches (Gearmatic & Pullmaster), FMC 20 GPM Water Injection Pump. Odometer Reads 28,665, 13-Speed Road Ranger Transmission.

Rotary D - SRS #3471

DESCRIPTION: 1987, Drilltech; Model: D25; Compressor: 840/350; Engine: CAT 3406; Mounted On: 1987 Ford L8000; Truck Engine Make: Ford 7.8 L; Condition: Working Drill; Tools/Options: Drilltech D25 (1987): Atlas 1000 Casing Hammer, Standard Mast, Carousel, Rod Box, 4 Hydraulic Outriggers. Rig Runs 4.5" X 20' Drill Pipe with 3.5" API Threads Pin Up. Rig can Carry 300' of Drill Pipe, New Hour Meter Reads 81 Hours, has been Replaced, Owner Estimates Total Hours to be approx. 12,000 on Deck Engine, Compressor was Rebuilt Several Years Ago (not very many hours ago as it was a spare rig), Truck has a Road Ranger 13-Speed Transmission and approx. 54,192 Miles on it. Includes 300' of Drill Pipe. Rig was used for a backup drill.

Rotary D - SRS #3384

DESCRIPTION: Drilltech; Model: D40K Long Mast; Compressor: Sullair 900/250 - Needs a New Cooler; Mud Pump: Available; Engine: PTO; Mounted On: CAT Tracks; Truck Engine Make: CAT 3406; Tools/Options: PRICE REDUCED OPEN TO OFFERS! Drilltech D40K: Mast (approx. 43', Deck Engine in Good Shape, was Well Maintained, does not Burn any Oil, No Leaks in Hydraulic System per Owner. Compressor is down, needs a new Oil Cooler. All Controls are Operated from an enclosed Air Conditioned Cab. Rig has Night Lights. Travel on Tracks has Forward and Backwards, can go where Trucks cant, Spins on a Dime, a few of the Pads need Replaced, sat a few years. Accepting Reasonable Offers. 2500' of 3.5" O.D. Range II Drill Pipe and Trailer is Available for an Extra Cost along with a 7.5" X 10" or 12" Mud Pump and a 10" Hammer to Drive Casing.. Condition:

Rotary D - SRS #3379

DESCRIPTION: 1983, Dresser; Model: T-70W; Compressor: See Below; Mud Pump: See Below; Engine: PTO; Mounted On: 4-Axle CCC; Truck Engine Make: Detroit Diesel 671; Condition: Excellent; Tools/Options: Dresser T-70W ( 1983): REFURBISHED IN 2014! 70,000# + Retractable Head with Heavy Swivel, 4-Part Range II 70,000# Casing Line, 2,500' Sand Line, 1,500# Swivel with Jib Winch, 24" + Hydraulic Pivoting Table with Tongs, Hangers, Jacks, Spinner & Hydraulic Under-Table Breakout, 35 GPM Bean Triplex, Full Decking, Steps, Ladders, LED and EP Lights, 3" Air/Mud Plumbing on Both Sides, Auxiliary Hydraulics with Controls, Terrell Box. Includes: Skid Mounted 7-1/2" X 10" Gardner Denver Duplex Mud Pump Powered by a Detroit Diesel471 Engine with Remote from Rig console, 1.,500 Gallon Mud System with a 4X8X3 Screen Shaker, 1,200' of 5-1/2" X 4-1/2" IF X 30' Drill Pipe with Slips, 1600 CFM Air compressor (off board), Parts/Service Manuals. Approx. 200 Hours since Refurbished in 2014. Hour Meter Reads 6,888.

Rotary D - SRS #3333

DESCRIPTION: 2012, Drillmax; Model: 350; Compressor: None; Mud Pump: 5X6; Engine: PTO; Mounted On: 2012 IHC 4300 4X4; Truck Engine Year: V8 Diesel; Tires: Good; Condition: Excellent; Tools/Options: Drillmax 350: Rig has approx. 3,600 Hours, 15,000# Pullback, 10,000# Pulldown, 8,000# Main Winch, 2,000# Sand Line Winch, Short Mast, runs 10' Rods, 36" Outriggers, Single Rod Loader. Rig is set up for Drilling Geothermal Loops in Tight Areas. Includes 200' of MJ 10' Rods, Rig has been very well maintained. Truck has Air Brakes and approx. 36,800 Miles on it.

Rotary D - SRS #3299

DESCRIPTION: 1998 Frame, Mast & Feed Cylinders, Diedrich; Model: D25; Compressor: None; Mud Pump: Moyno 3L6; Engine: PTO; Mounted On: 1998 Rubber Tracks; Truck Engine Make: Yanmar 83 HP; Tools/Options: Diedrich D25: All Hydraulic Rig. 1998 Frame, Mast & Feed Cylinders. D25 Parts have been Taken out and Replaced. New Aluminum, Hydraulic Diesel Tanks. Rig is Plumbed for an Auto Hammer (valves are there) has a Cathead Hammer Now. Replaced Planetary Winch. Yanmar has approx. 3 Hours on it. Feather Touch Hydraulic Controls, Featherlight Remote that Runs 7 Operations and Moyno, Rerun all the Hoses. Mast Extended to Accommodate an Auto Hammer. Kelly Bar Replaced with a Tophead Drive, Replaced the D25 Hydraulic Pump with a 32 GPM Piston Pump. More Power than a D50 but in a Smaller Package. Going to be Sand Blasted and Painted.

Rotary D - SRS #3175

DESCRIPTION: 1991, Drilltech; Model: D40K; Compressor: 1000/350; Mud Pump: None; Engine: New - CAT 3408; Mounted On: International Paystar 5000 Tri-Axle; Truck Engine Make: Cummins; Condition: Great; Tools/Options: Drilltech D40K: Angle Drill, New Deck Engine, Controls were Redone, Fresh Paint. 35-GPM Bean Pump, Oiler, Heater Engine, No Carousel. Includes approx. 725' of 4.5" X 25' Drill Rod. Truck has approx. 27,000 Miles and Compressor has approx. 1,600 Hours.

Rotary D - SRS #2913

DESCRIPTION: Davey; Model: M8A; Compressor: 500/125 Two Stage; Mud Pump: None; Engine: 671; Mounted On: 1981 Paystar 5000; Truck Engine Make: 8V92; Tires: Fair 24"-Rear, 22.5 Front; Condition: Fair; Tools/Options: Davey M8A: Blast Hole Drill. 7-1/2" Non-Retractable Table, 4-1/2" X 30' or 32' Kelly, 42' Mast, Front Jack, Dust Collector, Rod Rack. Miles Unknown, Speedometer Does not Work. 4X8-1/2' Steel Cab Skirting. Running Drill, Some Small Tools Included.

Rotary D - SRS #2829

DESCRIPTION: 1989, Driltech; Model: D 40 RC Drill; Compressor: Plumbed; Mud Pump: None; Engine: PTO; Mounted On: Komatsu Tracks; Truck Engine Make: CAT 3206; Tools/Options: Driltech D40A RC: Good Exploration drill, Sliding Angle Tophead Mast that will Drill up to a 30 Degree Angle. Large Bore Head, 40,000# Pullback, Hammer Oiler, 18' of Travel Using 4-1/2" X 10' RC Rod,350 HP Engine, 35 GPM Bean Injection Pump, Sample Recovery Cyclone, 2 Down Riggers and Dozer Blade for Stabilizing. 150 Gallon Fuel Tank. Also includes a Sullair 750/250 Air Compressor Powered by a Detroit Series 92 Engine, Mounted on a Morooka MST 1100 Track Carrier with Hydraulic Dump for Leveling Powered by a 6-Cyl. Diesel Engine. 2,861 Hours on Compressor, 150 Gallon Fuel Tank for Compressor Drill, 1,500' of 10' RC Pipe. Also Included is a 1989 +/- Mooroka MST 1000 Track Carrier/Dumper set up for Hauling Pipe Powered by a Komatsu 6-Cyl Diesel. Available for an Extra Cost is a Morooka MST 2000 Track Carrier Tender with 1000 Gallon 4-way Baffled Water Tank, 300 Gallon Fuel Tank with electric Pump, Slots, Low Center Racks on either Side for 36 10' X 4-1/2" RC Rods.

Rotary D - SRS #2408

DESCRIPTION: 1985, Davey; Model: DK 30; Compressor: 650 LeRoi; Engine: 6-Cyliner Detroit with PTO; Mounted On: Ford; Truck Engine Make: CAT 3208; Tools/Options: Davey DK 30 Year: Electronic Dust Collector with New Filers. New 4" X 32'6" Kelly, 30' Stroke, Original Compressor has been replaced with the LeRoi, CAT engine was rebuilt by Jasper, 3,000 Miles. Factory Heated Rear Cab. Includes 120' of 3-1/2" X 20' Drill Rod. Currently Drilling.

Rotary D - SRS #2163

DESCRIPTION: 1982, DSI; Model: Quick Drill; Compressor: Diesel Powered; Mud Pump: GD 5X6; Engine: PTO; Mounted On: International S1700; Truck Engine Make: DRT 466; Tools/Options: DSI Quick Drill: Dual Top head motors, sand line, breakout wrench, 4 Stabilizer Jacks, 1982 5-Speed Transmission. Needs cosmetics only. Passanger Side Fender needs repaired - see picture

Rotary D - SRS #1979

DESCRIPTION: 1975, Davey; Model: M8; Compressor: 500/125 2-Stage; Engine: 671 Detroit; Mounted On: Ford Louisville; Truck Engine Make: 534 Gas; Tools/Options: 7-1/2" Non-retractable table. 2 cyl. Myers water injection pump, 32-1/2' X 4-1/2" Kelly. Set up for water wells or test holes.

Rotary D - SRS #1978

DESCRIPTION: 1976, Davey; Model: M8; Compressor: 500/125 2-stage; Engine: 671 Detroit; Mounted On: 1976 Ford Louisville; Truck Engine Make: 534 Gas; Tires: Good; Tools/Options: 32-1/2" Kelly Bar, 2 cyl. Myers injection pump. Includes 400' of 5" steel, subs, bit, slip, wrench. 44 Rears in truck. Working Daily

Rotary D - SRS #1977

DESCRIPTION: 1976, Davey; Model: M8W; Compressor: 500/125 Davey; Engine: 671 Detroit; Mounted On: Ford; Truck Engine Make: 534 Gas; Tools/Options: 7-1/2" Retractable table, 26-1/2' X 4" Kelly Bar, < 500 hours on compressor, hydraulically driven water injection system. 44 Rears on Ford. Includes 100' of steel, sub, slips, wrench. Working daily

Southern Office:
1485 DeSoto Blvd N
Naples FL 34120
Phone: 239.774.1939
FAX: 239.774.6666

Northern Office:
Oil City PA 16301
Phone Toll FREE: 1.888.204.3907
Fax: 814.676.0378