Bucket Rig


Bucket Rig - SRS #3693

DESCRIPTION: 1979, Gus Pech; Model: SG48; Engine: CAT 3126 260 HP Rebuilt in 2006; Mounted On: 2005 Mack Granite CV713; Truck Engine Make: Mack AMI-370 370 HP; Tires: 80%; Condition: Good, Ready to Work; Tools/Options: Gus Pech SG48 Year: 1979: Deck Engine Rebuilt by CAT in 2006. 6,084 Hours, 4-Scope Square Bars Approximate Depth 96' with Crowd. (1) Drilling Bucket (several sizes available from 24" - 36"), 18,000# Capacity Braden Main Winch (new), 14,000# Capacity Vickers Auxiliary Winch. Updated Hydraulic controls pilot operated), Updated Hydraulic Pump (rugged gear pump), DowMax Turntable Motor (what Gus Pech uses today). Truck has approx. 78,000 Miles on it, 370 HP Engine, A/C, Air Ride Seat & Cab, Cruise Control, Non-Emissions Dependable Truck. Truck Runs, Drives and Stops Great with Lots of Power for the Weight it's Hauling. Truck & Rig both Start Well in the Winter. Rig Operates Well and is Quiet with the Turbo Charged Cat Engine. There are Ladders & Handrails on the Rig to Make Access Better. There is an Added Cylinder in the Tower to put the Pullout Arm in the Drilling Position. The Rig is in Good Condition and Ready to Work.

Bucket Rig - SRS #3600

DESCRIPTION: Calweld; Model: 175B; Engine: Chrysler 32 Industrial Gas; Mounted On: 1985 AFE 1/2 Cab Truck; Truck Engine Make: CAT 3208 with 3,000 Miles; Tools/Options: Calweld 175B: 42" Ring Gear, 75' Kelly Bar, 3 Hydraulic Outriggers. Truck Engine Only has 3,000 Miles on it. Includes (1) 28" Drilling Bucket, (1) 24" Cleanout Bucket, (1) Gad to Break Rock, (1) Boot to Drive Casing. Truck has been parked but was in working order when it was parked.

Bucket Rig - SRS #3520

DESCRIPTION: Calweld; Model: 250C; Engine: 6-Cylinder with 4-Speed Transmission; Mounted On: 1998 Freightliner FLD 120; Truck Engine Make: Cummins N14 425 HP Diesel; Tires: New; Tools/Options: Calweld 250C: 100' Kelly with 4" Stub, 300 Gallon Reserve Water Tank, 52" Ring Gear (drive gear in very good condition), 40" Heavy Duty Bucket with Reamer, (4) Hydraulic Outriggers, Hydraulic Side Boom and Lift, Hydraulic Crowd on Kelly. Truck has approx. 133,595 Miles on it.

Bucket Rig - SRS #3170

DESCRIPTION: 1978, Gus Pech; Model: Super George 48; Compressor: N/A; Mud Pump: N/A; Engine: Ford Industrial; Mounted On: 1995 IHC 4900; Truck Engine Make: DT 466; Condition: Working Order; Tools/Options: Gus Pech Super George 48: Hydraulic Table & Hydraulic Main Line. 48" Through Table, Deck Engine has a New Carburetor, Starter and Water Pump. Regular Maintenance Performed, 20' Telescoping Kelly with a depth of 100', (3) Hydraulic Jacks, Hydraulic Derrick Raising System, (2) Winches. (1) Used 30" Bucket Included. Rig does not have the Straight Back Push Assembly. Rig Runs & Works Well. Engine Hours Unknown. Odometer Reads 175,000 Miles.

Bucket Rig - SRS #3034

DESCRIPTION: Hughes; Model: CEZ 450; Engine: 471 Detroit; Mounted On: Unmounted; Tools/Options: Hughes CEZ 450: N65 Injectors in Detroit, Allison Transmission, 130' Digger, 7" Inner Kelly with 10" Outer & a 5" Tool Adapter. Rig has been sitting a while but ran well when it was used last. Rig was hooked to a 5299 American Crawler Crane using a 12' max. digging it.

Bucket Rig - SRS #2066

DESCRIPTION: 1975, Gus Pech; Engine: 300 Ford 6 Cyl; Mounted On: 1972 Dodge; Truck Engine Make: V-8 Gas 361; Tools/Options: Gus Pech : Rig has not worked in years but the 38" Ring Gear and Table are in Good Condition Manually Operated Main Line, Table is not Hydraulic. Truck motor was a good runner, didn't smoke or use oil. Compressor has a leak. Gears & clutch were good at that time also. Deck engine is an in-line. Bucket cable, 44,000 TS, jack shaft. 38" ring gear. Includes a 30" Bucket & 18" clean-out bucket. Truck has Newer Brakes.

Southern Office:
1485 DeSoto Blvd N
Naples FL 34120
Phone: 239.774.1939
FAX: 239.774.6666

Northern Office:
Oil City PA 16301
Phone Toll FREE: 1.888.204.3907
Fax: 814.676.0378