Auger

Search:
SRS#:
Category:
Keyword:

Auger - SRS #3775

DESCRIPTION: Electric; Mounted On: Skids; Condition: Runs Well; Tools/Options: Small and Compact Enough to Fit Through Doorways Inside of Buildings. Adjustable Mast, has a Cathead, Can Drive Samples, 4-Speed Transmission, Capable of Coring. Owner had it down 50' but probably no problem going deeper. Never ran augers with it, just casing but rig is capable of it. Never had any problem with the power unit, unit runs well.

Auger - SRS #3774

DESCRIPTION: Sprague Henwood; Engine: PTO; Mounted On: 1991 Tracks; Truck Engine Year: 3-Cylinder Deutz; Condition: Fair - Runs Well; Tools/Options: Sprague Henwood: Rig can Auger and Drill Core Rock. Has a 5' Stroke, Hydraulic Water Pump and Includes some Equipment and Trailer.. Condition: Fair - Runs Well. Currently runs 3-1/2" Casing down 100', Has Cored down to 365' and could have gone deeper. It will turn 4" Augers. Also has Two 3-Cylinder Bean Pumps available for Sale.

Auger - SRS #3701

DESCRIPTION: 1992 Totally Refurbished in 2014, Mobile; Model: B59; Engine: Cummins 4BT; Mounted On: 2014 Peterbilt 4X2; Truck Engine Make: PACCAR PX 9 260 HP; Condition: Near New SOLD; Tools/Options: Mobile B59: Mud Rotary, Coring, HSA & SPT Capabilities, Totally Refurbished in 2014, 20 Hours since, used on one job. Turbo charged, 100 HP Diesel Deck Engine & 260 ft./lbs. torque. Fuel Line connected to the Truck Fuel Tanks & Lockable Battery Box. 8,500# Main Hoist, Aux. Hoist, Auto SPT Hammer , SAFE-T-DRIVER Hoist, Breakout Wrench, Moyno 3L6, Drill Platform, Water Swivel, Clark Power Shift Transmission with 3 Forward Speeds and Reverse. 2-Speed Right Angle Drive with High and Low Range, Load Sense Pump, Proportional Valves & Electric over Hydraulic Switches for Auxiliary Functions. Mobile LIFELINE Emergency Shutdown system with Manual Reset Positioned in the Control Panel, Mobile's Mast Raise/Lower Alarm. Box/Water Tank Combo, Underbody & above Deck Auger Racks, Truck has < 2,000 Miles on it, Fuller 6-Speed Transmission, 12,000# Front Axle, 21,000# Rear Axle, Chrome Trim. Includes Auger & Sampling Tooling. SOLD

Auger - SRS #3766

DESCRIPTION: 1991, Diedrich; Model: D-120; Engine: John Deere Inline 6; Mounted On: 1996 Freightliner FLD 120; Tools/Options: Diedrich D-120 Year: 1991: John Deere Inline 6 Diesel was Rebuilt less than 7 Years Ago, Approx. 1,235 Hours. Transmission Rebuilt in 2017. Has a Moyno 3L8, Cathead, Fluted Kelly, (2) Auger Racks, (Dual Mounted Swinging Auger Racks), Tool Boxes, (4) Outriggers. Has a 3,000#, 7,000# and a 10,000# Winch. Truck has a Rockwell 10-Speed Transmission, Odometer Reads 151,777 Miles.

Auger - SRS #3765

DESCRIPTION: 1991, Diedrich; Model: D-120; Engine: John Deere Inline 6 Diesel; Mounted On: 2001 Sterling; Tools/Options: Diedrich D-120 Year 1991: approx. 990.3 Hours. 3,000#, 7,000# and 10,000# Winches, 3L8 Moyno. Cathead, Fluted Kelly, (2) Auger Racks, Tool Boxes, (4) Outriggers and 500 Gallon Water Tank. Truck has a 10-Speed Transmission and Odometer Reads 578,364 Miles.

Auger - SRS #3764

DESCRIPTION: TOOLING; Condition: Garage Kept, Not Used Much; Tools/Options: (14) 6-5/8" X 3' Mobile Augers, Two Drive Helmets (2" & 1-5/8") and Two Bits, Auger Plate and Hoist. Garage Kept, not Used Much.

Auger - SRS #3757

DESCRIPTION: 2020, Acker; Model: Kodiak; Engine: 22 HP Honda 690; Mounted On: Axle -Rubber Tires; Condition: Near New; Tools/Options: Acker Kodiak Year: 2020: Used on One Job, < 12 Hrs. Has Auger Capabilities and a Core Head, 140# Hammer Assembly, 3-1/4" and 4-1/4" Auger Guides. Power Unit - 15 GPM, 2000 PSI, 22 HP, 5 Gallon Hydraulic Tank. Feed Mechanism Consists of a Hydraulic Motor Driving a Single Strand Roller Chain. 3,000# Pullback and 3,000# Pulldown. Feed Speeds are Variable between 0-120 FPM. Welded Steel Mast with Supports and Guides. Feed System can Break Down to Change OAL from 47" Stroke (7'6" OAL) or 77" Stroke (10' OAL). Has Extra Anchor Points in the Front and Rear of the Unit. Jib has Removable Crown Block Assembly with Sheaves. Auger Drill Head is Hydraulically Driven with Planetary Design. The Head is Completely Sealed. Speeds are 0-60 RPM @ 1014 Ft Lbs. Core Drill Head is Hydraulically Driven and Includes an Integrated Water Swivel to an AWJ Drill Rod Connection. Speeds are 0-577 RPM @ 106 Ft. Lbs. Manual Rod Clamp to Handle Rod Size 1-3/4" - 3-1/2". Hydraulically Powered Breakout Wrench, Cathead, Auger Guide, Rod Bushing.

Auger - SRS #3749

DESCRIPTION: Shopbuilt; Model: Similar in Size to a Simco 2800; Engine: 4-Cylinder Deutz; Mounted On: 1989 Ford F-600; Truck Engine Make: Diesel; Tools/Options: Shopbuilt Similar to a Simco 2800: Cathead, Winch, Breakout Table, 10' Stroke, Mast Extension. 4-Speed Transmission in Truck. Also Includes an Older Simco 2400 on Skids Powered by a 2-Cylinder Wisconsin Gas Engine. Trailer that it was on is available. Multiple Heads are included along with Head Mounting Plates & Gear Boxes, Two Shop built Derrick Assemblies. Available for an Extra Cost IR 25 HP Motor that Turns a Moyno Pump and a Moyno 3L6 Pump with 4-Speed Tranny and a 15 HP Air Motor.

Auger - SRS #3748

DESCRIPTION: 1990, CME; Model: 55; Engine: PTO; Mounted On: IHI 50 Tracks; Truck Engine Make: Cummins Diesel; Condition: Ready to Drill; Tools/Options: CME 55 Year: 1990: Auto Hammer, 3L6 Moyno, 3 Winches, in/out Slide, Side to Side Slide Base, Rod Vice, Breakout Wrench. Carrier has Wide Rubber Tracks and approx. 2,658 Hours.

Auger - SRS #3742

DESCRIPTION: 2006, CME; Model: 45C; Engine: PTO; Mounted On: Yanamar C50R Tracks; Truck Engine Year: 2005; Truck Engine Make: 3-Cyl Deutz; Tools/Options: CME 45C Year: 2006: High Torque Double Chain Box, 3L6 Moyno Pump, 1,800# and 3,200# Hoists, 10" Drum Wireline, 140# Auto Hammer (calibrated), In-Out and Sideways Slide Base, Standard Mast. Deutz is a 2005, and has approx. 2247.5 hrs.

Auger - SRS #3720

DESCRIPTION: 1995, Mobile; Model: B 59; Mounted On: 1995 IHC 1900; Truck Engine Make: DT 466; Tools/Options: Mobile B59 Year: 1995: One owner drill, has been garage kept its whole life. Auto Hammer, 3L6 Water Pump, 3 Jacks, Steel Water Tank, (2) Auger Racks, Rod Storage. Approx. 4,264 Hours.

Auger - SRS #3712

DESCRIPTION: Mobile; Model: B54; Compressor: IR/Doosan 300/200; Engine: Diesel; Mounted On: 2010 IHC 7400; Truck Engine Make: CAT 430 HP Maxxforce; Tools/Options: Mobile B54: 24,000# Retract Force, 16,000# Ram Force, 13' Stroke. Mast is approx. 31' Mast from Ground to Top of the Crown. Single Rod Loader, 1,000# Jib Hoist & Winch, Hydraulic Break-Out Wrench, Hydraulic Rod Clamp, 8,500# Main Hoist, 4,500# Auxiliary Hoist, 1,200# Wireline Hoist. 2" Mast Standpipe, 2" Rotary Swivel, Splined Floating Spindle. Water/Foam Injection Pump, FMC 34 gpm Water Pump, Mission 3X2 Water Pump. Cotta Transfer Case, Linde Hydraulic Pump, FMC Bean Water Pump, Dennison Hydraulic Motor. Pullmaster Main Winch, Pullmaster PL6 Auxiliary Winch, Veljar Wireline Winch, Jib Hoist. Water Swivel, Lifeline, Mast Assembly has Rod Clamp, Breakout Wrench Assembly, Rod Loader Assembly, 10" Diameter Sheave, 3.5" Hydraulic Cylinder, Telescoping Table. 10-Speed Drill head Assembly Right Angle Drive Assembly. Floating Spindle, 36" Front Jack and a 36" Rear Jack, Auger/Rod Racks. Drill has approx. 7,124 Hours, 10,803 Engine Hours, Truck has approx. 785 Miles on it. Maintenance History Available.

Auger - SRS #3585

DESCRIPTION: 2000, CME; Model: 55; Engine: Cummins; Mounted On: 2015 IHI IC-50 Tracks; Truck Engine Make: Isuzu; Condition: Working Condition; Tools/Options: CME 55 Year: 2000: PRICE REDUCED !! 26' Mast, New Moyno 3L8, Three Winch Lines, Wireline, Rod Clamp, Line Extruder, Auto Hammer, Auger Rack, Slide Base/Wiggle Tail, 300 Gallon Water Tank. Carrier has < 500 Hrs. Good Tracks and all New Filters. Completely gone through. Repairs include a new hydraulic pump, water pump, winch repairs, paint, rod clamp, rotary box rebuild with new bearings and bushings and many more. Recently remounted on this carrier.

Auger - SRS #3665

DESCRIPTION: 1997, Soilmec R 312 HD; Mounted On: Tracks; Tools/Options: Soilmec R 312 HD Year: 1997: 12,952 Rig Hours.

Auger - SRS #3664

DESCRIPTION: 2009, Soilmec; Model: SR 30; Mounted On: Tracks; Tools/Options: Soilmec SR 30 Year: 2009: Engine has been Replaced, 678 Hours on New Engine.

Auger - SRS #3656

DESCRIPTION: Mounted On: Morooka MST-800 Carrier; Tools/Options: 1980's Morooka MST-800

Auger - SRS #3654

DESCRIPTION: Mobile; Model: B-53; Engine: 4-Cylinder Deutz Diesel; Mounted On: 2001 Ford F 650; Truck Engine Make: Cummins; Tools/Options: Mobile B-53 Year: 4-Cyl Deutz; Compressor: ; Mud Pump: ; Mounted On: 2001 Ford F 650; TrEngine: , ; Tools/Other Options: Two Winches, 435 Bean Pump, Three Jacks, Cathead, Slidramatic Head, 300 Gallon Water Tank. 60% New Hoses, Truck has approx. 47,000 Miles on it. . Rig is going to be painted.

Auger - SRS #3653

DESCRIPTION: Mobile; Model: B-53; Engine: Needs PTO; Mounted On: 2007 GMC 6500; Tools/Options: Mobile B-53: Rig Needs a PTO for the Drill Head, Valves need Resealed and whatever Geotech Options needed as this is just an Auger Drill. 10-Speed Rotary Drive System (needs PTO), Double Acting Hydraulic Cylinder Attached Directly to the Rotary Drive System, 14,140# Of Retract Force and 18,850# Of Ram Force. The Feed has a 6' (72") Stroke. 90° in the Transport Position. Angle Drilling Capabilities. All Electric Welded Tube Steel Channel Mast with Rigid Cross Bracing, 3-Sheave Crown Block Assembly. All Controls are Located in the Operator's Console Positioned at the Left Rear of the Body Fabrication, Easy access to Hoses and Fittings. Has Mobile's LIFELINE Emergency Shutdown System with Manual Reset Positioned in the Control Panel. Safety Alarm - Mobile's Mast Raise/Lower Alarm Warns the Operator and Others in the Proximity that the Mast is in Operation and to Watch for Overhead Obstructions such as Power Lines. Hydraulic Oil Cooler and Fan Assembly, 6,000# Main Hoist, 3,000# Auxiliary Hoist. Truck has approx. 186,000 Miles. Underbody Tool Boxes, Front and Rear Jacks..

Auger - SRS #3633

DESCRIPTION: Tooling; Condition: Slightly Used; Tools/Options: Various size 2-Key and 3-Key Used Augers, Jet Augers, Hex cor, Misc. Augers. Fishtail, Pointed Hammer, AWJ Pin X 1-5/8" Shank, AWJ Rod Ring, AWJ Rod, AWJ Hoist Plug, Auger Holders, AWJ Hammer Rod, 6-1/4" 2k HD Bullet, Cutterheads, DP 12", Drive Cap, Adjustable Auger Extension, Socket.

Auger - SRS #3551

DESCRIPTION: 2005, Diedrich; Model: D-120; Engine: 4-Cylinder Deutz; Mounted On: 2006 Freightliner; Truck Engine Make: Mercedes Diesel 330 HP 6-Cylinder; Condition: Ready to Drill - PRICE REDUCED !!; Tools/Options: Diedrich D-120 Year: 2005: PRICE REDUCED. Rig has a 4-Forward and 1-Reverse Transmission., 29' Mast, Auto Hammer, Hydraulic Rod Holder and Breakout Wrench, (2) Hydraulic Auger Racks, Auto-Chuck, FMC Bean Pump, with 40.6 GPM Capacity, Cathead, 3 Winches with a Wireline Winch. Rig has approx. 10,400 Hours, No Tooling Included. Dual Axle Truck with approx. 80,000 Miles on it, 52,000 GVW. Nice, Clean Rig.

Auger - SRS #3622

DESCRIPTION: 1976, CME; Model: 750; Engine: PTO; Mounted On: ATV; Truck Engine Make: 5-Cylinder Deutz with only 500 Hours; Tools/Options: CME 750 Year: 1976: Approx. 500 Hrs. on Engine. Auto Hammer, Rod Holder. This Rig has Extra Pullback as it has been Retrofitted with 2 Extra Ramps and Extra Leveling Jacks. Four Winches, 1,800#, 3,000# and a 10,000# Pull Master and a 8,000# Pull Master on the Front. Bean 435 Pump. Breakout Jaws and Wrench. No Hour Meter and Rig could use a Paint Job. Tool Boxes have some Rust on them.

Auger - SRS #3621

DESCRIPTION: Dando; Model: Twin Mast Terrier; Engine: PTO; Mounted On: Rubber Tracks (Small, Compact); Truck Engine Make: Kohler Diesel - EPA Compliant; Condition: Working Drill; Tools/Options: Dando Twin Mast Terrier: approx. 325 Engine Hours. Percussion Mast, Tophead Drive Rotary Head, Hydraulically Slides into Position. Can Sample and Perform SPT to a Depth of approx. 65' and Core to an approx. Depth of 164' plus Probing Capabilities. Single Line Pull Winch, Telescopic Mast. Swing-out control Panel with Illuminated Digital Blow Counter Mounted at the Front of the Rig. Sub-Frame, Auto Hammer: 140# and 30# additional Weight for TXDOT Drilling. Mast is Hinge/Pin Mounted to Main Structure, Hydraulically Raised & Lowered. Hydraulic Mast & Rotary Head, Rotational Speeds in Forward & Reverse, Side Inlet Water Swivel & BW Rod Connection. High - Max. Torque 155.6 ft.-lb. (Low Range: 1089 ft.-lb.) High Max. Spindle Speed 360 rpm (Low Range 70 rpm). Water Cooled Diesel Engine, Compact, Maneuverable Track Mounted Design Fitted with Tilt Mechanism Allowing Rig to Operate Vertically on Slopes Inclined up to 30°, Two Hydraulic Leveling Jacks, Includes 30' Solid Stem Augers, 4 Windowless Sampling Tubes, Associated Plastic Sampling Sleeves and Accessories, Spare Rubber Tracks, Indoor Exhaust Extraction Fans & Ducting, Small Trailer for Tooling and a Custom Enclosed Trailer. Unit Weighs approx. 3,220. Crawler Width is < 3' and approx. 3' with Control Box. Carriage Length 9', Height - 6.4', 5.25' Stroke, Runs 3.28' Rod. Approx. 15,000# Pullback and 2,200# Feed Force.

Auger - SRS #3614

DESCRIPTION: 1985, Mobile; Model: B-47; Engine: John Deere 4.5L; Mounted On: 2009 Ford F-450 4WD Super Duty; Truck Engine Make: 6.8L V10 Gas; Tires: Newer Drive Tires, Brand New Steer Tires; Condition: Ready to Drill; Tools/Options: Mobile B-47 Year: 1985: Hydraulic Actuated Mast, 2,000# Hydraulic Hoist, Koenig Wireline Winch, 3-Line Crown Block, Cathead, 3L6 Moyno, Slidramatic, 1-1/8" Hex Universal Auger Coupling, Safety Shut-off System, (2) Rear 24" Hydraulic Jacks, (1) Front Jack. Truck has approx. 175,239 Miles on it, Manual Transmission (rebuilt in 2018), New Clutch in 2018, New Drive Tires in 2017, Very Little Wear, New Steer Tires in 2019, Brand New. Drill had a new Alternator in 2019, Rig was Rewired in 2019, New Starter in 2019, New Hydraulic Pump and Motor in 2017, New Cathead Hydraulic Motor in 2017, Mast/Tower Reinforced/Rebuilt in 2018 (added 3rd Sheave for Second Winch, Not Installed), Slide/Feed Rollers Re-engineered and Rebuilt in 2019, Moyno Pump Rebuilt in 2019.

Auger - SRS #3608

DESCRIPTION: 1989, CME; Model: 750; Engine: PTO; Mounted On: Rubber Tire ATV; Truck Engine Make: 6-Cylinder Cummins Diesel; Tools/Options: CME 750 Year: 1989: One Owner Machine, Hydraulic rod Holder & Wrench (4.5"), 140# Automatic Hammer, 14" Jack Pads, Front PTO Mechanical Winch, 7,000# Hoist, 3,200# Hoist, 1,800# Hoist, Wireline Hoist for Bedrock Coring, Front Winch, Rollover Protection System (ROPS), Stop Disc on Hoist Cables, Moyno 3L8 Water Pump with Mechanical Transmission, 2" Water Pump Plumbing, Electric Engine Block Heater, Espar Engine Coolant Heater, 2J King Water Swivel, Custom Tool Tray on Front Bumper, Retrofit CME Double Clutch System, 2" Receiver Hitch on Rear, (3) 36" Leveling Jacks, Heated Tool Box at Helpers Station. Rig has approx. 19,000 Engine Hours (5,890 on Hour Meter, Meter was Replaced at approx. 4,000 Hours and Meter Rolled over at 10,000 Hours).

Auger - SRS #3305

DESCRIPTION: 1985 , CME; Model: 75; Compressor: None; Mud Pump: 3CL10 & Moyno 3L6; Engine: 6-Cylinder Air Cooled Deutz Diesel; Mounted On: 2006 Sterling Actera 6500 AWD; Truck Engine Make: Cummins; Condition: Excellent; Tools/Options: CME 75: Mud Rotary/Auger Drill. Cathead, Progressive Cavity Mud Pumps, (2) New Winches (installed Nov. 2017), Truck is 4WD and has 37,000 Miles on it. Ready to Drill. Capable of Small Water Wells, Large Diameter HSA, Monitor Wells, Drilled 150' - 385' Wells via Mud Rotary & Augers, Rock Cores, HSA, SPT Soil Sampling. 3CL10 Mud Pump Capable of Higher Downhole Pressure Requirements. Will Spin 75' of 8.25" HSA at Idle. Drills a Great 5' Core with the Adjustable Feed Detent in Hard or Soft Formations. Owner also used it as a Pump Service Hoist since the Mast is Tall Enough to Pull 20' Sections of Drill Rod and there are Two Winches.

Auger - SRS #3597

DESCRIPTION: 2012, Acker; Model: Soil-XLS; Engine: Deutz Diesel 97 HP 5-Cylinder; Mounted On: CAT Rubber Tracks; Tools/Options: Acker Soil-XLS Year: 2012: Deck Engine is a 5-Cylinder 97 HP @2,000 RPM with 12 Volt. Electric Start & Hydrostatically Operated Engine Leveler, Feed Mechanism Consists of Double Acting Chain Drive Mechanism Connected to a Hydraulic Cylinder with a 72" Stroke & Capable of 11,000# Upward Thrust, 11,000# of Pulldown. Feed Speeds are 0-72 FPM Up and Down. Drill Drive Taken from Prime Mover Through a Variable Volume Over Center Piston. Pump and Tandem Fixed Volume Pump. 8-Speed Hydraulic Drill Head with 3-5/8" Open Spindle, RPM is Infinitely Controlled in each Gear Range. The Transmission is a 4-Speed with a 2-Speed Hydraulic Motor Making (8) Speeds, The working Torque is 5,000ft.-lbs. with a maximum Speed of 1,000 PM, also Includes Drill Head Gear Oil Recirculation System with a Screw on Filter. Mast is of Welded Structural Steel Construction & Supports and Guides the Rotation & Feed Components, Positioned with Two Hydraulic Cylinders and Rigidly Held in the Vertical Position for Drilling and is Lowered to the Travel Position for Moving from Hole to Hole and Includes Mast Extension to allow for 10' Rod Pulls. Mast Mounting allows for Angle Drilling up to 45 ° as well as 90° Vertical, also Includes Mast Dump to 60" and Crown Block with Sheaves. Slide Head Movement is 12", Auger Guide, Hydraulic Leveling Jacks, Two Front and Two Rear with 36" Stroke and Lock check Valves. The Entire Drill is Mounted on a Structural Steel Frame and is Self Propelled, 18" Tracks, Independent and Reversible. Hydraulic Motor Drive as well as Full Function Remote Radio Control Operations with an Emergency Shutdown. 4.17 Ground Bearing Pressure. Carrier Speed is 3.27 MPH, 13" Clearance. Includes Fold up Operators Step, Low Clearance with Mast Extension for 15' Pipe. Hydraulic Powered Cargo Type Hoist, 8,500# Planetary Main Drum Hoist, with 75' of 5/16" Cable. Hydraulically Powered Wireline Hoist for Core Drilling, 1,000' of 1/4" Non-Rotation Cable with a Lifting Capacity of 800# with Brake. Hydraulically Powered Front Mounted Winch with 20,000# Capacity Capable of Operating in Conjunction with Tracks. 4" Ackermatic Hydraulic Chuck Assembly, Handles HW Rods. Designed for High Production Wireline Rock Coring. Moyno 3L6. 160 Gallon Steel Water Tank and Rod Rack.

Auger - SRS #3596

DESCRIPTION: 1987 , CME; Model: 45B; Engine: Hercules Gas - New Rebuilt; Mounted On: 2003 Chevy C4300; Truck Engine Make: Gas; Tools/Options: CME 45B: Refurbished in 2017. Auto Hammer (calibrated in 2017/18), Calibration Available. Main Winch and tool Winch, Cathead, Rebuilt Transmission, Clutch, Jacks, Right Angle & Rotary Box, New 3L6 Moyno Pump, New Rebuilt Deck Engine. Truck has AC, Automatic Transmission and approx. 135,000 Miles on it.

Auger - SRS #3579

DESCRIPTION: 1991, Mobile; Model: B80; Mud Pump: 3X4; Engine: PTO; Mounted On: 1992 IHC 4900 4X4; Truck Engine Make: DT 466; Condition: Working Drill; Tools/Options: Mobile B80 Year: 1991: Mud Rotary Capabilities, Good Geothermal Drill. 3 line Machine (main line, sand line and auxiliary line), Bean Injection Pump, Side to Side Tophead, 22' Stroke, Breakout Wrench, Homemade Rotary Table, (3) Leveling Jacks. Rig is set up to run either 3.5" or 4.5" Drill Rod. Includes 250 Gallon Mud Slayer, Welder with Torch Bottles and 100' of 4.5" X 20' Drill Rod. Single Axle Truck, has a 6-speed Transmission and approx. 165,000 Miles on it. 33,000# GVWR (12,000# Front and 21,000# Rear).

Auger - SRS #3575

DESCRIPTION: Tools/Options: Mobile Omnex Radio T 300 Series.

Auger - SRS #3574

DESCRIPTION: Mobile; Tools/Options: Mobile Auto Chuck.

Auger - SRS #3573

DESCRIPTION: Mobile; Model: B57 - B59 RAD;

Auger - SRS #3565

DESCRIPTION: 1989, Mobile; Model: B61; Engine: Ford 300 Gas; Mounted On: 1989 Ford F-800 4X4; Truck Engine Make: 429 Gas; Tires: Good; Tools/Options: Mobile B61 Year: 1989: Deck Engine Runs good. Rod Chuck, Wiggle Tail, 200 Gallon Stainless Water Tank, Moyno 3L6. Truck has a Rebuilt Transmission on Deck and Cab, New Carb. Needs Work on Boxes, Water Pump Runs. Truck has approx. 37,000 Miles on it.

Auger - SRS #2893

DESCRIPTION: 1978, CME; Model: 55; Compressor: N/A; Mud Pump: N/A; Engine: Borg-Warner Gas; Mounted On: 1995 Ford F-800; Truck Engine Make: Cummins 6BT; Tires: 6 New Michelin's; Condition: Good; Tools/Options: CME 55 Year: 24' Mast, 3L6 Moyno Pump, 200 Gallon Water Tank, 3,000# Winch, Cathead Winch, (3) 36" Jacks, In-Out Slide Base, Auger Rack, Tool Boxes, Drillers Platform. Rear Wheel Drive Truck, T-18 Transmission, Air Brakes. No Pintle Hitch. Hour Meter Reads 657. Recently Totally Gone Through.

Auger - SRS #3557

DESCRIPTION: Mobile; Model: B80; Engine: 4-Cylinder Deutz; Mounted On: Chevy Kodiak; Truck Engine Make: 3208 CAT; Condition: PRICE REDUCED; Tools/Options: Mobile B80: Four Leveling Jacks, 3-Cylinder Bean Pump, Winch Line, Wire Line, Sliding Tophead, 8-Speed Transmission. Truck has a 10-Speed Transmission. Includes 100' plus of 4" Augers, 500' BX Wireline, NQ Barrel, 130' of N Rods. Last time it was on a job was approx. late 2018.

Auger - SRS #3528

DESCRIPTION: 2011, Mobile; Model: B-37 RAD; Engine: PTO; Mounted On: MT 20 Rubber Tracks; Truck Engine Make: Deutz 230 Diesel Tier 3; Condition: Good; Tools/Options: Mobile B-37 RAD Year: 2011: Rig, Track Carrier and Engine was Recently Refurbished and is Ready to Drill. Hour Meter Reads 1,904. Hydraulic Components Powered by Dual Piston Hydraulic Pumps, both Pumps @ 3,600 PSI. One Pump is used for the Rotation, the Second is used for Feed, Auxiliary Functions and the Water Pump. 60 Gallon Capacity Hydraulic Oil Tank. Two Speed Hydraulic Motor through a Planetary Drive. Two-speed Head has 3600 lb.-ft of Torque @ 75 RPM in Low Speed and 1800 lb.-ft @ 150 RPM in High Speed. High Speed Coring Head with 390 lb.-ft Torque @ 772 RPM. Both Tophead Drives are Mounted on the EZ-SELECT which allows for one touch control to change from standard rotation to high speed coring. Two Hydraulic Mast Raising Cylinders. Mast and Feed Frame Fold to 90° for Transport and is Angle Drilling Capable. SLIDRAMATIC Rotary Drive System. 15,7003 Pullback @ 0-80 fpm and the Maximum Pulldown is 11,700# @0-106 fpm. 6' Feed Stroke, approx. 15' from the Ground to the Top of the Crown. 4,500# Auxiliary Hoist, SAFE-T-DRIVER Hoist with 900# Capacity, Bi-directional Hydraulic Planetary Hoist with Hydraulic Brake, Hydraulic Break-Out Wrench, Hydraulic Rod Clamp, 140# Auto SPT Hammer, 2,500# Cathead, Side Port 1-1/2" NPT Rotary Swivel, 2" Mast Standpipe, 1-5/8" Hex Safety Drive Coupling. 3L6 44 GPM Water Pump, 2" Suction Port and 1-1/4" Discharge Port. Tracks are 99" Long, 20,000# GVWR, 2-Speed Hydraulic Planetary Drive. Narrow Access Carrier has Extendable Tracks that allow for a Total of 12" of Track Adjustment, Minimum Width of 35". 13,000# Expandable Track Carrier Expandable from 35-3/8" to 47-3/8", 74 HP Air Cooled Engine, 12 Volt Starting Circuit, 37 Gallon Fuel Tank, Two Front and Two Rear Leveling Jacks.

Auger - SRS #3519

DESCRIPTION: Spiradrill; Mud Pump: 4" Mission Hydraulic Centrifugal; Engine: 6-Cyl Deutz Diesel; Mounted On: 1998 Mack; Truck Engine Make: E7-400; Tires: New; Condition: Excellent; Tools/Options: Spiradrill: Entire Deck Retracts/Slides about Two Feet. 4" Mission Hydraulic Pump, 2" High Pressure Swivel, (3) Hydraulic Winches with 3 Lines, Hydraulic Rope Cathead, 22' Stroke, 12,000 Ft Lbs of Variable Drilling Speed Torque. Includes 15 Joints of 5' X 5" X 1-5/8" Solid Stem Auger. 80' of 6" HAS, 50' of 4" HAS Available. All Tooling Complete for Geotech Work, Arod, 5" 6' collar. Arod for Truck has an 8-Speed Transmission and approx. 225,558 Miles on it, New Rubber, Wide Tires on Front. Rig and Truck in Excellent Condition.

Auger - SRS #3492

DESCRIPTION: Simco; Model: 3000; Engine: PTO; Mounted On: Tracks; Truck Engine Make: Perkinis Diesel; Tools/Options: Simco 3000: TEMPORARILY OFF MARKET Early Version of a Simco 2800, Same Drive and Hydraulics. Has the Rotary Head. TEMPORARILY OFF MARKET

Auger - SRS #3474

DESCRIPTION: 2018, Mobile; Model: Voyager V2200; Engine: Kohler CH25; Mounted On: Frame; Tools/Options: Mobile Voyager V2200 (2018): Hydraulically Powered Drill, Two Mast Stabilizers, Maximum Rotary Speed of 150 RPM, Maximum Torque of 950 ft-lbs, 6' Stroke, 5,000# Pullback, 5,000# Retract, Feed Speed Down & Retract 90 ft/Min., Variable Speed. Air Cooled 25 BHP Gasoline Engine, Electric Start. Onan or Deutz Engines are Optional. Variable Displacement Hydraulic Pump. Estimated Operating Capabilities: Rotary & DTH Drilling, 3.5" OD: 125', Capabilities Vary According to Subsurface Conditions.

Auger - SRS #2946

DESCRIPTION: 1988, Mobile; Model: B24; Engine: Diesel; Mounted On: Trailer; Condition: Operational Working Drill; Tools/Options: Mobile B24 1988: Cathead, 15' Mast, Vickers Pump, Swing-out Head (no slide). No Water Pump. Brand New Tires and New Rope.

Auger - SRS #3177

DESCRIPTION: 1990, Mobile; Model: B57; Compressor: None; Mud Pump: None; Engine: Cummins 4BT-3.9; Mounted On: 1990 Ford F-800; Truck Engine Make: Diesel; Condition: Operational; Tools/Options: Mobile B57: Approx. 6,358 Rig Hours and approx. 158,126 Miles on Truck. Moyno 3L6 Pump, (3) Hydraulic Leveling Jacks, Auger Racks on both Sides, Cathead, Wiggle Tail, Slide Base (2) Winches - 8,500# & 3,200#. One of the Hydraulic Lines needs Replaced, Owner will either Replace it or Compensate for it. No Tooling Included. Ready to Work. Gearboxes have been Rebuilt. PRICE REDUCED, GREAT BUY. Will remove from the truck and sell just the rig.

Auger - SRS #3448

DESCRIPTION: CME; Model: 55; Mud Pump: Moyno; Engine: Deutz; Mounted On: Trailer; Tires: All New 14 Ply; Condition: Good; Tools/Options: CME 55: Rig is Hydraulically Driven, Recently Rebuilt, 3 Hydraulic Jacks, All New 14 Ply Tires, No Auto Hammer.

Auger - SRS #3447

DESCRIPTION: Mobile; Model: B53; Engine: PTO; Mounted On: 1989 Ford 700 2WD; Truck Engine Make: CAT; Condition: Working Condition; Tools/Options: Mobile B53: Transmission on the Drill was Rebuilt approx. 2013 and Never Used Since. 140" Safety Hammer (high speed drop hammer/winch), (3) Hydraulic Jacks, 2 Winches. Mast Measures 19.75' from the deck to the winch. The mast has a telescopic auger guide at the base which can be extended below the deck manually. Fair Condition due to it needing some general TLC, but rig is in working order. Truck has approx. 60,000 Miles on it, 5-Speed Transmission, Electric over Hydraulic Braking System.

Auger - SRS #3446

DESCRIPTION: Early 1990's, Mobile; Model: B24; Engine: Deutz Diesel; Mounted On: Box Frame (similar to a truck camper, can back a pickup under it); Condition: Like New; Tools/Options: Mobile B24 (Early 90's) Like New Condition. Box Frame it is Mounted on is Similar to a Truck Camper, Can back a Truck Under it to Load onto a Pickup Truck. Owner has a Trailer Available for an Extra Cost, Rig Could bolt to a the Deck of a Trailer. Engine has Low Hours (approx. 200 Hrs), Cathead, Runs 5' Augers, Swing-Out Head, Step Type Mast that is Removable. Also has some Small 2.25" Diameter Augers Available.

Auger - SRS #3437

DESCRIPTION: 1968 - Totally Rebuilt in 1987, CME; Model: 55; Mud Pump: Moyno 3L8; Engine: Ford 4-Cylinder 300 Cubic Inch Gasoline Industrial; Mounted On: 1994 Chevrolet Kodiak; Truck Engine Make: CAT 3116 Diesel; Condition: Good; Tools/Options: CME 55 Year: 1968: One Owner, Well Maintained Unit. New in 1968 and Totally Rebuilt in 1987 (new drill deck, new water tank, new side rails, new Moyno 3L8, new CME safety hammer, new 7000# hydraulic hoist, new leveling jacks, new drillers step, new Ford 300 Cubic Inch Gasoline Industrial Deck Engine). In 1994 the Rig was Installed onto a then new 1994 Truck. At that time new auger racks, new tool boxes, and a new water tank was installed. 140# Auto Sampling Hammer, 27' Mast, Stainless Steel Water Tank, 1,800# Winch, 3,200# Winch, 7,000# Winch, Hydraulic Rod Holder, Three Hydraulic Leveling Jacks, Two Underbody Auger Racks, Side toolboxes on Drill Platform. Single Axle Truck, Custom Front Bumper with Pintle Receiver & Tow Hooks, Rear Pintle Receiver and Wiring for Towing a Trailer, Single Front and Dual Rear Tires. Truck has approx. 108,349 Miles on it. Deck Hour Meter Reads 8624.9. Combined Weight of Truck and Rig is 31,440# with Full Fuel Tanks, Tools and 120' of Drill Rod and 100' of 2-1/4" ID Augers.. Condition: Good

Auger - SRS #3409

DESCRIPTION: Mobile; Model: B-53; Compressor: None; Mud Pump: Yes; Engine: PTO; Mounted On: 1995 Ford F-800 4X4; Truck Engine Make: Diesel; Tools/Options: Mobile B-53: Auto Hammer.

Auger - SRS #3405

DESCRIPTION: 1996, Mobile; Model: B 59; Mud Pump: Moyno 3L8; Engine: Cummins Diesel; Mounted On: 1996 Ford F-900; Truck Engine Make: Diesel; Tools/Options: Mobile B-59 (1996): Automatic Transmission, Main Winch, Auxiliary Winch, Safety Driver Winch Plus Wireline, rod Clamp, Breakout Wrench, Cathead, Slide Base, Front & Rear Hydraulic Jacks, Two Under Bed Auger Racks, 500 Gallon Water Tank. Truck is equipped with Air Brakes, 10-Speed Transmission and has approx. 117,000 Miles on it..

Auger - SRS #3403

DESCRIPTION: Mobile; Model: B-56; Compressor: N/A; Mud Pump: 3L6 Moyno; Engine: 240 Ford Gas; Mounted On: 1994 IHC 4900; Truck Engine Make: Diesel; Tools/Options: Mobile B-56: Under CDL, Two Swing Out Auger Racks, Cathead, 400 Gallon Water Tank, Two Leveling Jacks,.

Auger - SRS #3402

DESCRIPTION: Mobile; Model: B57; Compressor: None; Mud Pump: Moyno 3L6; Engine: Ford 300; Mounted On: Gemco Articulating Buggy; Truck Engine Make: Detroit Diesel; Condition: Runs Good; Tools/Options: Mobile B57: Auto Hammer, (2) Leveling Jacks.

Auger - SRS #3364

DESCRIPTION: Mobile; Model: B-53; Compressor: N/A; Mud Pump: N/A; Engine: Detroit Diesel; Mounted On: 1979 Ford F600; Truck Engine Make: Diesel; Condition: Needs Work; Tools/Options: Mobile B-53: Truck Runs but not Licensed for the Road. Rig Runs, was being used for Coring Work. No Slide base, Rotary Slides on a Piston to the Driller's Right, Cathead, Tag Line Hoist. Water Pump is a Little Weak and there are a few Leaks. No Tooling Included. With a pump and a little work could get it running right or could be purchased for a parts rig.

Auger - SRS #3280

DESCRIPTION: 1988, Deeprock; Model: Ram 10 XL; Compressor: None; Mud Pump: None; Engine: Deutz Diesel; Mounted On: 1970 Ford F600; Truck Engine Make: 361 Ford V8; Tools/Options: Deeprock Ram 10 XL: Rig has been Sitting Indoors for a While. Engine in Truck was Rebuilt Prior to being Parked (very low mileage). Deutz Engine Powers Hydraulics. 806 Hours on Rig, 140# Hammer, Three Hydraulic Stabilizers. Includes 30' of 6-1/4" ID Hollow Stem Augers, 35' of 4-1/4" ID Hollow Stem Augers, 45' of AW Rod with Pin-to-Pin Couplings, 50' of 4-1/2" Solid Stem Augers, 30' of 5-1/2" Solid Stem Augers, One Fishtail Bit, Auger Hoisting Assembly, Two 24" Split Spoons, Two 18" Split Spoons, Mounted Steam Cleaner with 1400 psi, 209 Degree Water, Adjustable Nozzle.

Southern Office:
1485 DeSoto Blvd N
Naples FL 34120
Phone: 239.774.1939
FAX: 239.774.6666

Northern Office:
Oil City PA 16301
Phone Toll FREE: 1.888.204.3907
Fax: 814.676.0378